general-discussion
help
nibble
bit-c
tidbit
accessories
build-chat
hacks-n-mods
firmware
show-and-tell
scramble
diagrams-etc
snap
Luke? - hi, i just finished today my nibble key...
hi, i just finished today my nibble keyboard and now im trying to change the keymap from us to germany. ive changed the keymap already in via and loaded the updated layout on to my keyboard but the keymap seems to be still the old one :/
some - Is the rotary encoder supposed to interf...
Is the rotary encoder supposed to interfere with the plate going on? I can't get the plate on without an amount of force that I suspect would break the plate. The encoder is in the top right position. I checked and the encoder works fine so I don't think I've installed it wrong. Would anything bad happen if I just filed the plate down? I need maybe half an mm more of clearance
Luke? - hi guys, is it possible to rotate the b...
hi guys, is it possible to rotate the bongo cat animation by 180 degrees?
Sebastian Perez - @jay | nullbits I have been h...
@jay | nullbits I have been having trouble entering into bootloader mode on my Nibble and was hoping you could help. Whenever I hit the physical reset button while I have the QMK toolbox open I hear the keyboard disconnecting and connecting on windows, I see it too on the console. But it does not go into flashing mode. I have tried shorting it on the back of the pcb, I have tried every combination of keypresses I could find online, but no luck as of yet. I am starting to read online that it coul...
Auci - does anyone know how to programm the sce...
does anyone know how to programm the sceens on the snap?
Auci - im testing my keyboard and when I press ...
im testing my keyboard and when I press the N key, the spacebar is also pressed
eldermonster - # Hot Teen & Onlyfans Leaks :und...
Hot Teen & Onlyfans Leaks :underage: :peach: https://discord.gg/esexx @everyone
A wild hisoka Appears! - Having some trouble wi...
Having some trouble with the underglow leds, only some of them light up, but the keyboard is otherwise fully functional.
Solution:
wasn't a problem with the other leds, was a problem with the last working one up the chain. AFter digging around on the forum i found some info on how they communicate, and it wasn't a power issue, but the data bus
eldermonster - # Hot Teen & Onlyfans Leaks :und...
Hot Teen & Onlyfans Leaks :underage: :peach: https://discord.gg/esexx @everyone
Auci - I started soldering the mill max hot swa...
I started soldering the mill max hot swap sockets but I did a really bad job and a lot of them are kind of crooked, also because of the tape I used, some of them have tape inside them. Another issue is all the tape residue left on the board from said tape.
Is it safe to desolder them with wick and just use new sockets? And what can I use to clean the PCB board from the tape residue?...
Skoknor - hey folks, I'm in the middle of a nib...
hey folks, I'm in the middle of a nibble65 build and have soldered everything in, underglow LED's are all glowing red and the big LED is lit blue.
At current I have the oled_bongocat flashed and have rerouted the OLED with Kynar but can't get it to respond, have tried flashing and reflashing with different firm but nothing's changed, if I mess with the wiring on the OLED too much the whole board disconnects and LED's go out.
me lost help pls 😦...
Solution:
First, send pics. Second, what's Kynar? Third, if messing with things causes the LEDs to go out, it sounds like there's a short somewhere and the wiring to the OLED is bad.
Message Not Public
Sign In & Join Server To View
cold butter - also - should the long side of th...
also - should the long side of the pins be facing up?
cold butter - hi! i am building my tidbit and i...
hi! i am building my tidbit and i'm blanking on how to solder the microcontroller. am i supposed to solder both the tops and bottoms of the header pins? no part of the microontroller is soldered in this picture yet, wanted to ask first
gulpmonster - hey everyone. just completed the ...
hey everyone. just completed the snap75 build this weelend and i love the keyboard. I used the snap_via.hex file from github, but I am struggling with getting the oleds to work and the underglow leds to have any other color than red. The keyboard works otherwise (typing on it now). I have never used QMK before so this is kind of new territory for me. Any pointers? Thank you!
AJ - Anyone know what the rotary encoder pins a...
Anyone know what the rotary encoder pins are supposed to be set to in config.h for the Snap? The instructions say, "Check that the A and B pins are set in QMK config.h and that ENCODER_ENABLE = yes in QMK rules.mk." but it doesn't say what they're supposed to be set to. I have no idea which pins these hook up to...
Solution:
For what it's worth, I figured this out by looking at the old github repo: https://github.com/nullbitsco/snap/blob/main/config.h
Aezkme - Hello everybody. I soldered all the di...
Hello everybody. I soldered all the diodes etc. After testing I found 2 rows that don't work at all. Can anyone tell me which pin on ic2 I should check (I'm pretty sure about these pins)