configuration

need help to set up configuration for ratrig v3 size 400 got lost to understand the guide i already installed klipper on board oct v1.1 already installed ratos on pi and installed vcore three config connected to my pc going to machine removeed # on printer.cfg to what i have and now got lost how to do the next step .. i got error ( control _pin in section bltouch must be specified !! . what the next steps notice my knowledge almost basic on klipper
No description
111 Replies
eastern-cyan
eastern-cyan3y ago
Please upload printer.cfg
future-harlequin
future-harlequinOP3y ago
ok downloading discord in the pc .. its really old pc hope it work
eastern-cyan
eastern-cyan3y ago
Take screenshots and upload if its easier
future-harlequin
future-harlequinOP3y ago
thats will take many .. give me sec and i will install discord
future-harlequin
future-harlequinOP3y ago
by the way its without (1) but upload it 2 times
eastern-cyan
eastern-cyan3y ago
You have not selected a probe?
future-harlequin
future-harlequinOP3y ago
how i can select it from config file ?
eastern-cyan
eastern-cyan3y ago
Remove the “#” In printer cfg is selecting that option
future-harlequin
future-harlequinOP3y ago
remove them all ?
future-harlequin
future-harlequinOP3y ago
there is 4 of them
No description
eastern-cyan
eastern-cyan3y ago
The ones that matches the printer you have
eastern-cyan
eastern-cyan3y ago
No description
future-harlequin
future-harlequinOP3y ago
thats getting hard to understand . but how i know which one will work with me .. what info you need to answer me
eastern-cyan
eastern-cyan3y ago
Im on phone doing nightshift with baby so cant go to PC. If you have a BL tell the firmware that by using the config
future-harlequin
future-harlequinOP3y ago
did it oh sorry .. appreciate ur help and time
eastern-cyan
eastern-cyan3y ago
Np,is it working now?
future-harlequin
future-harlequinOP3y ago
got anther msg
eastern-cyan
eastern-cyan3y ago
Shoot
future-harlequin
future-harlequinOP3y ago
No description
eastern-cyan
eastern-cyan3y ago
What probe you have? Need to tell printer how to address it by selecting pin option in the pic you sent (i think,not running BL myself)
future-harlequin
future-harlequinOP3y ago
i use bltouch and about probe u mean bltouch or super pinda like that ? or you mean endstop?
eastern-cyan
eastern-cyan3y ago
This is for a Inductive example
No description
eastern-cyan
eastern-cyan3y ago
I would think you use same pinoption
eastern-cyan
eastern-cyan3y ago
No description
future-harlequin
future-harlequinOP3y ago
ok you choose the first one because u use super pinda maybe .. but how i know which one i chose for bltouch ? ok same
eastern-cyan
eastern-cyan3y ago
Try the same
future-harlequin
future-harlequinOP3y ago
same not working
eastern-cyan
eastern-cyan3y ago
What does it say?
future-harlequin
future-harlequinOP3y ago
No description
future-harlequin
future-harlequinOP3y ago
same
eastern-cyan
eastern-cyan3y ago
Cant help you then 🤷‍♂️
future-harlequin
future-harlequinOP3y ago
np thanks for your time dude i appreciate it
future-harlequin
future-harlequinOP3y ago
i am looking for octubs diagram its said pin code pb6 and pb7
eastern-cyan
eastern-cyan3y ago
Do you have physical end stop?
eastern-cyan
eastern-cyan3y ago
No description
future-harlequin
future-harlequinOP3y ago
no
eastern-cyan
eastern-cyan3y ago
RatOS renames pins
future-harlequin
future-harlequinOP3y ago
aha thats so hard to understand how its work not like voron
eastern-cyan
eastern-cyan3y ago
Send the printer cfg you got now please
future-harlequin
future-harlequinOP3y ago
eastern-cyan
eastern-cyan3y ago
@miklschmidt you got a sec?
future-harlequin
future-harlequinOP3y ago
i can give u full acces to my pc if. u want
eastern-cyan
eastern-cyan3y ago
No ty.
eastern-cyan
eastern-cyan3y ago
before that one maybe
No description
miklschmidt
miklschmidt3y ago
sure what's up
eastern-cyan
eastern-cyan3y ago
Would you have a look at the cfg and see if anything is messed up,doing it from phone on the web is pita 🫣
miklschmidt
miklschmidt3y ago
sure @gskwt
#####################################################
# BL Touch
[include config/z-probe/bltouch.cfg]
# Inductive/Capacitive probe
[include config/z-probe/probe.cfg]
#####################################################
# BL Touch
[include config/z-probe/bltouch.cfg]
# Inductive/Capacitive probe
[include config/z-probe/probe.cfg]
You can't use both a bltouch and probe
future-harlequin
future-harlequinOP3y ago
i got ratrig v3 400 and i have zero experience how to set the congf 🙂
miklschmidt
miklschmidt3y ago
Same on line 194-201 rest looks fine You just need decide which you want to use. What is actually on your printer?
future-harlequin
future-harlequinOP3y ago
rat rig v3 400
miklschmidt
miklschmidt3y ago
What probe is on your printer? Is it a bltouch or an inductive probe?
future-harlequin
future-harlequinOP3y ago
bltouch
miklschmidt
miklschmidt3y ago
then comment out line 199 and 201 and 63 And you should be good to go You're having problems because you're configuring both a bltouch and an inductive probe at the same time. That's like wearing boots and slippers at the same time, it doesn't work very well.
future-harlequin
future-harlequinOP3y ago
aha ok i will try it now errors gone and waitting to connect
eastern-cyan
eastern-cyan3y ago
No error is a good start 🦖
future-harlequin
future-harlequinOP3y ago
yeah thanks alots but i think i missing something now yeah serial
miklschmidt
miklschmidt3y ago
Flash your board with RatOS firmware
future-harlequin
future-harlequinOP3y ago
where i put the serial id ? how to flash it ?
miklschmidt
miklschmidt3y ago
you don't This is not a voron All of this is automated.
future-harlequin
future-harlequinOP3y ago
yeah for that i am lost with it
miklschmidt
miklschmidt3y ago
Yeah you're thinking too much. Its easiest if you just follow the instructions. Anyway I'll send you the binary you went way past the compilation step
future-harlequin
future-harlequinOP3y ago
i did but lost with it
miklschmidt
miklschmidt3y ago
Where did you get lost?
future-harlequin
future-harlequinOP3y ago
with config
miklschmidt
miklschmidt3y ago
You barely have to do anything with the config You just pick what's on your printer Anyways
future-harlequin
future-harlequinOP3y ago
aha
miklschmidt
miklschmidt3y ago
What board are you using? Octopus v1.1
future-harlequin
future-harlequinOP3y ago
yeah
miklschmidt
miklschmidt3y ago
Aight gimme a sec
future-harlequin
future-harlequinOP3y ago
ok
miklschmidt
miklschmidt3y ago
Rename to firmware.bin and flash via sd card
future-harlequin
future-harlequinOP3y ago
ok
miklschmidt
miklschmidt3y ago
Steps are in the docs for formatting the card if you need them. Check that firmware.bin is renamed to firmware.cur on the sd card.
future-harlequin
future-harlequinOP3y ago
thanks alots it shown me FIRMWARE after flash in the sd card is that mean it flashed ?
eastern-cyan
eastern-cyan3y ago
No description
future-harlequin
future-harlequinOP3y ago
i think it flashed every thing work
eastern-cyan
eastern-cyan3y ago
Just follow the instructions and its easy,dont overthink it. Im off the bed wish you luck
future-harlequin
future-harlequinOP3y ago
heat up the nozzle work and moving the axis work thanks alots dude gn8 thanks dude
miklschmidt
miklschmidt3y ago
YW 🙂 have fun with your new printer!
future-harlequin
future-harlequinOP3y ago
its 1.3 years old but now got time to work on it 🙂 hope i can understand the next step like lvling bed etc ... thanks for ur help
miklschmidt
miklschmidt3y ago
New old printer then 😂 Everything is set up for you, all you need to do is use the start and endprint macros (check the docs, if you're not using one of the official presets for superslicer or prusaslicers). Set up your z_offset first of course, but that's all.
future-harlequin
future-harlequinOP3y ago
thanks checking it after i clean the real and grease them again is there bed mesh ? @miklschmidt got question about the fans .. i used 24V fans do i need remove the jumper from V5 slot to V24 ?
future-harlequin
future-harlequinOP3y ago
my jumper in grean side which it 5V do i need to remove it to blue side ?
No description
eastern-cyan
eastern-cyan3y ago
The jumpers for fan voltage is above that output pinout,3 jumper option on every fan header.
future-harlequin
future-harlequinOP3y ago
oh good morning dude then what is that what i mark ?
eastern-cyan
eastern-cyan3y ago
No
future-harlequin
future-harlequinOP3y ago
i read it is for the fans like 5/ 12 /24 voltage
eastern-cyan
eastern-cyan3y ago
No description
eastern-cyan
eastern-cyan3y ago
Headers and jumpers
future-harlequin
future-harlequinOP3y ago
yeah got it but do u see where i mark on right side there is jumper on the grean side do i leave it or remove it
eastern-cyan
eastern-cyan3y ago
Leave as documented
future-harlequin
future-harlequinOP3y ago
in document they said remove it and i forget to remove it . my bad
eastern-cyan
eastern-cyan3y ago
This assumes you use 24v fans move jumper according to the V you want
No description
eastern-cyan
eastern-cyan3y ago
For 4028 follow that documented guide
future-harlequin
future-harlequinOP3y ago
yeah i saw that parts but i thought they was talking about that suction which i marked coz in voron u need to move the jumper for which Voltage you use such V5 V12 V24
eastern-cyan
eastern-cyan3y ago
🤷‍♂️ i know nothing about vron
future-harlequin
future-harlequinOP3y ago
even me .. my knowledge not that much too .. but i got friend using voron he was try to help me yesterday then he got confused until you guys help me yesterday all work perfect i try fan was working heating too work moving work good but what i am missing now is how to use bed mesh and lvling but i saw on document it will do bed mesh before each print .. and the s offset i need to press home then in the ratos page there suction for set the Zoffset hope i am not wrong
miklschmidt
miklschmidt3y ago
yes
future-harlequin
future-harlequinOP3y ago
so i move it to blue right ?
miklschmidt
miklschmidt3y ago
The ones you've painted over on that image is for a probe port you're not even using, not the fans. As @squeegiee said, the voltage selectors for the fans are above the fan headers.
future-harlequin
future-harlequinOP3y ago
oh not the fan so i leave it or remove the jumper yeah got it then fans all good .. only that i send there is jumper do i need to remove it ? sorry guys for that tons of questions .. but i dont want to do something wrong that will burn my workshop 😦 horizontal_move_z can't be less than probe's z_offset extruder when i print it reverse
eastern-cyan
eastern-cyan3y ago
Add a ! In the config will change rotation Its all in the docs
future-harlequin
future-harlequinOP3y ago
done work very well not got anther problem the tension wheel on extruder not touching the filament 🙂
eastern-cyan
eastern-cyan3y ago
Cant help you with that one 😂
future-harlequin
future-harlequinOP3y ago
i know lol there is gap between the wheels
eastern-cyan
eastern-cyan3y ago
What extruder do you run? Is it for 1.75?
future-harlequin
future-harlequinOP3y ago
orbiter 1.5 yeah 1.75

Did you find this page helpful?