Unknown command MESH_CONFIG

I get this message when I start a print. (RatOS 2). Bed Mesh is done and named "ratrig", it's not applied.
For sure I have forgotten to set up something, but I don't find it.
Thanks for your help!

Helge Keck•12/7/22, 5:58 PM

thats a PAM command

Helge Keck•12/7/22, 5:58 PM

its still in your slicer configured but you havent installed it again on ratos 2.0

Helge Keck•12/7/22, 5:59 PM

https://github.com/HelgeKeck/pam

GitHub

GitHub - HelgeKeck/pam: PAM for RatOS

PAM for RatOS. Contribute to HelgeKeck/pam development by creating an account on GitHub.

uncertain-scarletOP•12/7/22, 6:01 PM

I double checked, haven't installed this yet (waiting for the final Pi to arrive). Searching through the config.txt for "pam" doesn't give any results.

uncertain-scarletOP•12/7/22, 6:01 PM

I'll take a few minutes to go through my printer.cfg line by line, but I am quite sure

Helge Keck•12/7/22, 6:02 PM

thats the issue, its still configured in the start_gcode in your slicer, but not available on your printer

Ccolossal-harlequin thats the issue, its still configured in the start_gcode in your slicer, but not...

uncertain-scarletOP•12/7/22, 6:04 PM

thanks. of course. for sure you just heard my hand facepalming hard.

Iicke thanks. of course. for sure you just heard my hand facepalming hard.

Helge Keck•12/7/22, 6:04 PM

i did

Helge Keck•12/7/22, 6:04 PM

Helge Keck•12/7/22, 6:04 PM

the windows almost broke

HHelge Keck https://github.com/HelgeKeck/pam

ptegler•12/12/22, 6:11 AM

ref post https://discordapp.com/channels/582187371529764864/1050109013175578696/1050109092754100254
HK...does this conflict with.... or co-exist (run in parallel ) with the Adaptive Purging ?
https://discordapp.com/channels/582187371529764864/1050109013175578696/1050109330873139280

Pptegler ref post https://discordapp.com/channels/582187371529764864/1050109013175578696/...

Helge Keck•12/12/22, 11:58 AM

adaptive purging?

ptegler•12/12/22, 5:24 PM

yes. I've noticed this purge works better when it's closer to the PAM'ed style mesh area (their version of localized meshing) The default purge line up the y-axis (at least on my bed) seems thinner than the brim printed around my item being printed. Plus the wipe always leaves a string when it zips over to the print area . This is kind of a blob and line and wipe all in one but right next to the item you are printing.

ptegler•12/14/22, 5:45 AM

no eval? oh well...guess I need to uninstall PAM and install that asset and compare. tnx

HHelge Keck adaptive purging?

ptegler•12/17/22, 4:06 PM

dooohl! thought the link was there https://github.com/kyleisah/Klipper-Adaptive-Meshing-Purging

GitHub

GitHub - kyleisah/Klipper-Adaptive-Meshing-Purging: A unique leveli...

A unique leveling solution for Klipper-enabled 3D printers! - GitHub - kyleisah/Klipper-Adaptive-Meshing-Purging: A unique leveling solution for Klipper-enabled 3D printers!

Unknown command MESH_CONFIG

Similar Threads

Similar Threads

Similar Threads