you can read more about it here
you can read more about it here
Pwill someone be able to help me out soon to run through the initial set up of my Rhino?
HWow, I had no idea!
I've tried my USB hub to no avail. Maybe I can go get a PCIe USB card next... Thanks again for the enlightenment!
I've tried my USB hub to no avail. Maybe I can go get a PCIe USB card next... Thanks again for the enlightenment!
Sis the latest Ryzen chipset driver from AMD installed?
Sis Disable Global C-State in the BIOS enabled? if it is then disable it
Scan you run prime95 on you computer for a while?
Sor convert a video in handbrake
Sand see if your computer crashes
Stry out all the ports on the back of the motherboard, there are cpu ports and chipset ports. the faster ones like usb3.0 and usb c are generally the cpu ports, also the newer the port like if ts usb 3 gen 2 or somethingits more likelyto have better signal integrity then just a usb 3 or a usb 2. for some people this happens only cpu ports or mother board ports only and for others it happens on both
Snext step would be to buy a powered usb hub or powered pcie card
SInateck PCI-e to USB 3.0 (4 Ports) PCI Express Card and 15-Pin Power Connector, Red (KT4001)
Slots of people say this one worked
Sbut if you find another cheaper where you live with sata power like this one then give it a try
Salso try plug in all other usbs in the usb hub and plug in the rhino one alone in the best usb port on the back of your motherboard like usb c or the turquoise ports, those should be the best
Sthis might decrease the noise from the other usbs just enough for it to work
Stry multiple different usb hubs, 3.0, powered , non powered, pcie, etc to try and get the cleanest signal possible
Soh one more is to try out pcie 3 in bios
Shere is another idea
Suse a really short usb cable from the rhino and plug it straight into a powered usb 3.0 hub with good quality thick shielded wire
Sthen the usb hub into the computer
Stry adding a faraday cage or some kind shielding around the rhino logic board so it doesnt get affected by the magnetic currents from all the other components
HWow, that's a lot to digest. I did update AMD's chipset driver to the latest and saw no improvement. I'll try one thing at a time as you suggested. I think it's pretty clear now that it has something to do with signal integrity.
SYeah I think so too. Basically try to get the best signal possible and do the settings changes.
SSUse this website for anything you get
SIf the product your looking at is on here then its guaranteed to meet usb specifications
HRoger, thanks!
PHey sorry if I'm missing something obvious, but is there any documentation/tutorials of any kind to show me how to go about initial set up of the Rhino base?
WHey, there's the in-depth technical guide about the system: https://www.youtube.com/watch?v=iNhRD2Bsb8o
This one was made for the kits, but applies to the Rhino too.
Grab the software here: https://vpforcecontrols.com/usb/rhino/
This one was made for the kits, but applies to the Rhino too.
Grab the software here: https://vpforcecontrols.com/usb/rhino/
YouTubeValmantas Palikša
This is a first introduction of the Rhino FFB system that will be available soon for purchase as a DYI kit. This system will enable enthusiasts to build a plug-an-play FFB joysticks with custom mechanics. Contact me for details if interested.
Contacts:
VPforce Discord Channel: https://discord.gg/Y7YmFGHbee
DCS Forums: https://forum.dcs.world/p...
Contacts:
VPforce Discord Channel: https://discord.gg/Y7YmFGHbee
DCS Forums: https://forum.dcs.world/p...
MHaha I'm going through the same thing right now
MIs crazy
MF14 omg
PHa ha, like I said, sorry about missing the obvious!
MI'm just restarting dcs all the time when I make changes
Pright, well I need to do the firmware possibly & just install the software etc. really just want to get the Ka50 set up & go test this thing out!
MFinally just figured out I had the wrong ffb axis inverted
MF5 trim was driving me insane
MHey if the stick is waaaay more further forward than I think it should be for the f5
MDo I change a setting?
WI think that's the way it is in DCS
Wthe F-5 has short FWD travel, and much more AFT travel ?
WCan't rememeber exactly
MYeah
MMaybe I have to change the endstop
MIt's there a way to make changes in the app on the fly without having to restart dcs?
WOh it messes up DCS if you change settings in the app ?
WGenerally it should work without restarting DCS
MNah the stick just goes dead sometimes
WAh, I'll need to have a look
MAhhhh gimme a day to trial and error it
MAmazing dude tho thanks so much