Helge Keck•348d ago
wie gesagt mal ohne filament versuchen und mit offener lasche
erst mal testen ob es mechanik oder electronic ist
Rigattoni•348d ago
@Helge Keck Motor ist in Ordnung, der rennt leise. Das ist mechanisch, die Nylon-Rädchen springen wohl über die Antriebswelle.
Der Motor wird nur knalleheiß
Helge Keck•348d ago
das ist normal
Rigattoni•348d ago
Sieht aus, als wäre der Extruder nach gut 1,5 Jahren in den Fritten.
Direkt nen Neuen bestellt. Diesmal bei Amazon für 68 Euro
Helge Keck•348d ago
hättest dir auch einfach das zahnrad set kaufen können
Rigattoni•348d ago
Das kaufe ich mir dann zusätzlich Ersatz ist immer gut.... Finde ich beim Ali aber gerade nicht. Hasst du ne Quelle?
Da gibt es nur eins für den 1.5
Helge Keck•348d ago
irgendwo hab ich das mal gesehen
Rigattoni•348d ago
https://de.aliexpress.com/item/1005003902054224.html
Der Kram vom 1.5er passt auf den 2.0
Helge Keck•348d ago
das überrascht mich etwas
dachte immer das 2.0er set ist anders weil der extruder an sich ja kürzer geworden ist
Rigattoni•348d ago
ich habe die beiden gerade zerlegt. Das Einzige was nicht passt, das ist die Extruderwelle.
Da ist die Aufnahme der 3 Zahnräder dünner
Helge Keck•348d ago
gut zu wissen
Rigattoni•348d ago
Selbst die Lager der 3 Zahnräder sind identisch. Bis auf die Transport-Welle ist der Kram gleich.
Rigattoni•348d ago
Nur diese Aufnahme der 3 Planetenräder ist 1mm dicker. Alle Lager und Planetenräder passen vom Orbiter 1.5
Rigattoni•348d ago
Extruder rennt wieder wie gehabt.
Helge Keck•348d ago
repariert?
Rigattoni•348d ago
Jep, drückt auch 25mm mit 25mm³/s problemlos.
Helge Keck•348d ago
nice
Rigattoni•348d ago
Hab ja einen neu bestellt, der kommt dann rein und der reparierte in die Ersatzteil-Kiste.
Fehler ist auch gefunden: Das Zahnrad des Motors dreht ja die Planetenräder und die greifen in die Verzahnung in dem festen Teil des Extruders. Dadurch wird die Welle des Extruders gedreht. Nun greifen die Planetenräder nicht mehr in den umlaufenden Zahnkranz. Dadurch wurde die Extruderwelle nicht mehr richtig angetrieben, wenn Druck benötigt wurde.
Wenn das "normaler Verschleiß" ist...
Want results from more Discord servers?
More PostsStop services automaticallyHi guys,
after updating to RatOS 2.0 my memory/CPU load (unfortunately only using a RPI Zero 2 W) haIs my rail eating itself?Just got around to lubricating my rails, left hand rail for the front and back axis (can't remember Belt grabber/adjuster broke. Replaced the adjuster but I have a new noise now.So while printing, I noticed a layer shift so I stopped printing and inspected. It turns out the bel4028 Lüfter an SKR2ich habe einen Artic Lüfter den Übergangsweise am Octopus betrieben habe übrig. Diesen wollte ich jUnregelmässige erste SchichtGuten morgen. Im internationalen Bereich hat mir niemand geantwortet, darum probiere ich es hier aucUnable to update RatOs repo after branch changeHello guys, I've tried upgrading my probe to unklicky and followed a blogpost which said to switch tOdd resonance shape on VC300What to do here? There's resonating sound from EVA, I've checked every screw and part, but nothing. Inconsistent first layerI have very weird behaviour on my first layer, which I can't seem to get right.
What I have tried: Probleme bei der zweiten Schicht!Hallo habe einen Orbiter 2.0 verbaut und alles gemacht ESteps , PID Tuning usw und dann Probedrucke Clogged Nozzel?My print failed overnight and it looks like my mosquito hotend is trashed. I'm not sure what happeneratos vanishedafter much complication i finaly got my set up to work and then i could not connect or find ratos.loWhat to improve?Hi, i don't know how to interpret input shaper graphs. Is it ok or not, and if it's not good what toY-Rails not tightening.400 with enclosure.
I am trying to attach my Y rails using the included M3x12 and 3030 Drop-in T-NuExtruderwerte richtig einstellenHallo habe Mal ne Frage zum Orbiter 2.0 habe den in der cfg einkommentiert der untere der Beiden wPossible to Not Home between prints (multicolor)?Hello,
I am trying to test some multicolor prints on my Vcore.
I've tried a few settings without anBoard detected but unresponsiveI have an Octopus 1.1 and I tried reflashing multiple times. I tried doing it remotely, over sd cardZ Offset not savingNot quite sure why, but the past couple prints my z offset resets itself and i have to manualy adjusratos + octoprintI want to use ratos but i also want to use octoprint. I know i can set up klipper with octoprint butfirst layer issues - too high & too low issue over print areaI got issues with the first layer being too high & too low in different areas of the bed. Mesh seemsFR: Ability to connect to "mixed WPA2-PSK/WPA3-SAE access points"Hi,
at this moment currently generated `wpa_supplicant.conf` by `RatOS Configurator` allows to conne