Pytorch 2.1.1 is bad, use 2.1.0+cu118, as cu123 also bad
Pytorch 2.1.1 is bad, use 2.1.0+cu118, as cu123 also bad
TI think better off using Kandinsky @fusionbrain 
P
FI shared sdxl lora ones earlier, still testing all the possible settings, i got about 22 trainings left then will share my best one
Fi think depends on each project
Fbut on automatic1111 working so far
Fi replied you from patreon too
Fdon't forget to activate venv of Automatic1111 Web UI
pip uninstall torch torchvision torchaudio xformers --yes
pip3 install torch torchvision torchaudio --index-url https://download.pytorch.org/whl/cu121
pip install xformers==0.0.23
pip uninstall torch torchvision torchaudio xformers --yes
pip3 install torch torchvision torchaudio --index-url https://download.pytorch.org/whl/cu121
pip install xformers==0.0.23
Mthanks got it working with torch 2.1.1 and xformers 0.23
Fy4es you can
Fi should compare
Fgreat
Pwhen i started training
P
Pi received this warning
PtensorRT are used to train in kohya?
Phowever, he continued with the training and is ongoing.
Fnope
Fpip3 install torch torchvision torchaudio --index-url https://download.pytorch.org/whl/cu121
need to add the https
need to add the https
Fyou are right. while copy pasting it was gone
KHi I’m still getting the older version of torch and xformers when doing it
Pyou can try specify version like this pip install torch==2.1.0 torchvision==0.16.0 torchaudio==2.1.0 --extra-index-url https://download.pytorch.org/whl/cu118
PIf you have another version in the requirements it will replace the installed version.
Fyou need to activate venv
KI did still same issue
KTried this too still same
Pis on A1111 ?
KYep it shows it’s installing etc, but when I load a1111 still on old version
PAre you running on Windows or Linux?
KWindows
Pon webui-user.bat do you have this line TORCH_COMMAND="pip install torch==2.1.0 torchvision==0.16.0 torchaudio==2.1.0 --extra-index-url https://download.pytorch.org/whl/cu118" ?
Por like this
KYep tried and still the same
Pin modules folder
Pfile launch_utils.py
P
Pwhenever you run a1111 it will revert to this version. You can change it directly to the version you want, be careful, make a backup of the file first.
KEven with that still the same
KShit... I've started to get NaN's again 
Pif you type pip show torch which version do you get?
KHmm it shows the old version
Pyour requirements_versions.txt file is still the original, you didn't make any changes to it, right?
KI didn’t make any changes to that
SAnyone here that might be able to help me with a SD question ? im hitting a road block.
PWell, I would manually uninstall the current version, with pip uninstall, leaving the correct version you want in the launch_utils.py file. I would make sure that there is no SET TORCH_COMMAND line in web-user.bat and then run web-user.bat again and it will install the environment. But if you are booting from another bat than the original, it may be doing something earlier and causing the problem.
Fwhat it is it
Fif you use custom installers etc
Fthey could be overwriting
K@Dr. Furkan Gözükara You have any good tip regarding cropping and rescaling?
I have many images like this and I want to crop the car. Tha image is high resolution enough to get only the car in 1024x1024, but using BIRME for example it only crops the image and rescales it so i get a square image with alot of background still there...
I have many images like this and I want to crop the car. Tha image is high resolution enough to get only the car in 1024x1024, but using BIRME for example it only crops the image and rescales it so i get a square image with alot of background still there...
K
