Rhino is not Bound in MSFS Controls. My Rhino Joystick does not respond while in the H160 Cockpit. W

Rhino is not Bound in MSFS Controls. My Rhino Joystick does not respond while in the H160 Cockpit. While in the H160 Cockpit there is no movement of the Joystick. This means H160 cannot fly.

B9OP•1/24/24, 7:43 PM

My Rhino Joystick does move while using the VPforce FFB Configurator Tool

BB9 Rhino is not Bound in MSFS Controls. My Rhino Joystick does not respond while in...

Number481•1/24/24, 7:44 PM

I dont understand. Did you configure a button to use as force trim in TelemFFB as I said ?

B9OP•1/24/24, 7:45 PM

Yes I did do as you decribed

Number481•1/24/24, 7:46 PM

do you still see the red x in TelemFFB for MSFS?

BB9 See image of my VPforce FFB Configurator

Number481•1/24/24, 7:48 PM

your adjustment knob is connected to spring force and is turned to 0.... TelemFFB needs spring force enabled to be able to center the controls

Number481•1/24/24, 7:48 PM

and simulate force trim

Number481•1/24/24, 7:49 PM

it won't start sending axis data to MSFS until the controls are centered so it knows where they are

B9OP•1/24/24, 7:49 PM

The Red x has cleared and it is blue, see image

B9OP•1/24/24, 7:49 PM

Maybe I have to restart my PC?

Number481•1/24/24, 7:50 PM

B9OP•1/24/24, 7:53 PM

It is Obvious I have no idea how to setup the Rhino Software. Has any one made a video showing and describing how to setup the Rhino Software?

BB9 It is Obvious I have no idea how to setup the Rhino Software. Has any one made a...

Number481•1/24/24, 7:55 PM

Its not hard once you understand what a few basic things do and how they work together... Without TelemFFB running, is there any spring force on your Rhino or is the stick limp?

I have to step away for work stuff for a while but will be back later

B9OP•1/24/24, 7:56 PM

ok. The stick is limp and the black dial is a Zero

Sunshine•1/24/24, 8:00 PM

So my DIY kit came, these servos are HUGE!

Sunshine•1/24/24, 8:00 PM

B9OP•1/24/24, 8:01 PM

When I restarted my MSFS simulator the red x came back

BB9 When I restarted my MSFS simulator the red x came back

TrigaNZ•1/24/24, 8:16 PM

Set your POT1 to Master Gain and turn it up. Do a calibration. Apply and Store. Close configurator. Open FFB. Open MSFS.

B9OP•1/25/24, 2:44 AM

Thank you very much for your incredibly amazing support with my Rhino Software Setup. My Rhino is working Perfectly. Thank you.

Caprice•1/26/24, 10:07 AM

Hello, absolutely loving the Rhino, its a true gamechanger for me. I was noticing a problem with my endstops, when i put even a little force on them, they "break" and the stick goes past the point, and the axis goes limp.

Caprice•1/26/24, 10:07 AM

This is not very much force at all.

CCaprice Hello, absolutely loving the Rhino, its a true gamechanger for me. I was noticin...

walmis•1/26/24, 10:13 AM

That could be the motor stability safety protection, try reducing Spring and Damper LPF values in Expert settings

walmis•1/26/24, 10:13 AM

Try something like

Wwalmis That could be the motor stability safety protection, try reducing Spring and Dam...

Caprice•1/26/24, 10:35 AM

Thank you will try. Amazing work on this!

Gadroc•1/26/24, 7:05 PM

Has anyone got the VKB adapter to work? The screw used as the anti-rotation post is larger than the holes on the VKB grips (3mm instead of 2.5mm of the post on the real base.)

GGadroc Has anyone got the VKB adapter to work? The screw used as the anti-rotation pos...

Fierce_Fire•1/26/24, 7:14 PM

What part do you mean? I just used whatever came with the grip and it mounted in one go

Gadroc•1/26/24, 7:16 PM

The little silver nub… it slips into one of two holes on the grip for either straight or 15angle. That pin is 2.5mm round. The vkb adapter has an m3 screw in the same location that does not fit into the grip. Prevents the grip from seating all the way.

Fierce_Fire•1/26/24, 7:18 PM

Wierd, I dont remember how mine looked there but I believe it fit into a slot

Fierce_Fire•1/26/24, 7:18 PM

Wait, what rev adapter is this?

Fierce_Fire•1/26/24, 7:19 PM

Iirc the newest type doesn't fit and needs a seperate adapter

Gadroc•1/26/24, 7:24 PM

My equipment is mark 3

Gadroc•1/26/24, 7:25 PM

New mark IV is different connector all together

Gadroc•1/26/24, 9:08 PM

I replaced the M3 screw with a M2.5 screw and while it's a little loose should prevent the grip from twisting and shorting out the contacts.

Fer•1/27/24, 4:02 AM

Hello, I have a problem with my winwing adapter I can’t secure the adapter in position it stays loose and can’t hold the stick in place, any ideas ?

ddrake1984•1/27/24, 5:04 AM

maybe a rubber washer

Fer•1/27/24, 5:23 AM

Fer•1/27/24, 5:23 AM

I don’t know if this is normal

Fer•1/27/24, 5:33 AM

I have to adapters and both do the same.

TrigaNZ•1/27/24, 5:33 AM

Not normal. Start from scratch and make sure you have threaded correctly. mine is tight as with the F-16 grip.

Fer•1/27/24, 5:34 AM

Yes both are threaders correctly

Fer•1/27/24, 5:34 AM

To the top

FFer Click to see attachment

ddrake1984•1/27/24, 5:44 AM

yeah, rubber washer should fix that

Fer•1/27/24, 6:16 AM

thanks

Fer•1/27/24, 6:16 AM

ill try thatbut where should i put it__

ddrake1984•1/27/24, 6:20 AM

between the grip (metal bit) and the top plastic (where you plug it in)

Fer•1/27/24, 6:41 AM

Fer•1/27/24, 6:42 AM

in both sides??

ddrake1984•1/27/24, 6:48 AM

just 1 should do it

ddrake1984•1/27/24, 6:48 AM

it creates something to compress against

Fer•1/27/24, 7:38 AM

ok hope that helps

R7-Cedar•1/27/24, 11:39 AM

Hello, while all aircraft I have are working well on the Rhino, only Ka-50(And Ka-50III) are not being able to work with TelemFFB. I found following entry in log, __ Exception in thread Thread-2:
Traceback (most recent call last):
File "main.py", line 746, in process_data
File "aircrafts_dcs.py", line 592, in on_telemetry
File "aircraft_base.py", line 863, in _update_heli_engine_rumble
TypeError: float() argument must be a string or a real number, not 'NoneType'

During handling of the above exception, another exception occurred:

Traceback (most recent call last):
File "traceback_with_variables\print.py", line 67, in printing_exc
File "traceback_with_variables\print.py", line 98, in wrapper
File "main.py", line 794, in run
File "main.py", line 750, in process_data
File "traceback_with_variables\print.py", line 39, in print_exc
AttributeError: 'NoneType' object has no attribute 'write'

During handling of the above exception, another exception occurred:

Traceback (most recent call last):
File "threading.py", line 1009, in _bootstrap_inner
File "traceback_with_variables\print.py", line 92, in wrapper
File "contextlib.py", line 153, in exit
File "traceback_with_variables\print.py", line 70, in printing_exc
File "traceback_with_variables\print.py", line 39, in print_exc
AttributeError: 'NoneType' object has no attribute 'write'
any help will be appreciated,

Rhino is not Bound in MSFS Controls. My Rhino Joystick does not respond while in the H160 Cockpit. W

Similar Threads

Similar Threads

Similar Threads