im running a CM3 base with no springs and clutch, works well but Im sure the Rhino will be better
im running a CM3 base with no springs and clutch, works well but Im sure the Rhino will be better
SYeah hehe
SAre you running the cm3 with extension
SAnd is the stick positioned just above your legs
SFFB helps but having good ergonomics helps way more
Fdont worry, it is. Havent used the cm3 so cant comment on the feel personally but heard the rhino is better, and actual ffb trim is amazing
Trunning the 20cm extension with the T50, it sits a little bit too high
SWhere does it sit
Tbetween my legs, but my arm doesnt rest on my leg, so I think its a bit too high. its perfectly comfortable, but I'd prefer it a little lower
SYou should be able to rest your wrist on your legs while flyng and just control the stick with finger tips
SIts really important. Not only stopping your hand from tiring and leaning on the stick but to give it a reference point. Its a lot harder to control your whole arm precisely in air then it is a small portion of your hand
TAye, Im sure it'll make things a lot more precise
TI've held off fixing it til now. Next up is a DOF reality H3 !
SJeez
Tmight need to wait tho
SIsnt it more simple to configure the stick properly
TI'm sure it is 
DQuick question can I mount the directly to my simrig floor?, I got a Simlab GT1 EVO with optional metal floor.
Fits has a few mounting holes on the bottom
Fso if you have a drill, probably
Fif not youll have to use the #
faq to see if the holes line up
faq to see if the holes line up
Mthanks - note your comments so with something like the spitfire or the p51 I should see some noticeable centre position drift - note I had seen this but assumed flying the ah64 just before (with the force trim) may have somehow reset or messed up the centre - so I am guessing after reading reply as I load a new aircraft the centre (initially) should go back to the old calibrated centre (from the VPforce software but may drift as you fly? - also noticed on the p51 and spitfire the ffb didnt feel right (like when the apache had the curves applied even though I had reset all the curves!) - to correct this guessing the best way is just to tweak the VPforce configurator software settings? - if yes are they any particular settings I might need for helicopters (apache now feels good!) but that might not be required for fixed wing?
Malso unrelated question - currently using a virpil z with the mongoose grip but tempted to try the thrustmaster f18 grip instead - has anyone tried this and is it a worthwhile change?( just concerned it might not work as well as the mongoose - while the f18 is a better grip (all metal) its also much heavier so unsure how it might effect the performance of the rhino)
II went up 40 places in 1 day. 46 more to go boys! Almost there!
IMy name will be red very soon haha
Bdont base your expectation of quality purely on it beeing metal, considering they dont say which one it is on their website its likely cheap zink alloy.
deciding factor should be the layout and amount of inputs combined with what you like to fly
deciding factor should be the layout and amount of inputs combined with what you like to fly
Mactually have used one before - and while the mongoose has more buttons and is excellent want to give the f18 one a try - question was more how well it works with the rhino (as its heavier than the mongoose) and other grips which may be an issue as using the z extension with it....
WIt works fine (I use the heavy TM F-16), though some more balancing adjustments will be needed using the software features.
SBloody hell yes, I've just gone to 25 to go. Nice.
CLets go! down below 700 now, 670 to go.
S47 lets goooooooooo
SOh your the one b4 me 
ISerial 506?
II'm 505
IMy brother has 503 left. I told him to reserve when I did but he forgot until January 
SYes
Mjust over 150 left for me - I was thinking that would be several months but at the rate things are going....
V:package: 
RHINO #0460 Has Shipped!
RHINO #0460 Has Shipped!
CWow! made a jump forward since yesterday. Last I had 108 Rhinos before me. Now it‘s 69!
Snice
V:package: 
RHINO #0461 Has Shipped!
RHINO #0461 Has Shipped!
HMine just shipped, #0461! I thought it would be another few weeks. Just be sure when you get the order form request as your number nears to fill it out quickly, because my position changed twice right before and after I submitted it.
VYa i have even longer. Only been pre-ordered for over a week now.
VWhen I first put my pre-ordered in a week ago it said 798 to go and now it's 746. Going to be awhile
P2025 will be a great year for you
VThanks for pissing on my parade
IDid you get an alert when your order was ready to be paid for?
SI’m down to 23 to go and just got the email today asking me to complete the order form with any required accessories. I guess I’ll get an invoice to pay fairly soon.
ICould anyone share some pictures of how they have their Rhino mounted?
ITrying to get ideas of how I'll mount mine.
IIdeally looking for a low cost DIY modifcation of like a cheap/standard chair.