Any tips for my question for ac adapter disconnecting easily. Am I the only one with this issue as t

Any tips for my question for ac adapter disconnecting easily. Am I the only one with this issue as there is no one saying anything. Usb adapter is not loose but ac adapter is kinda loose I tied wire down below around my mount so usually it is nit dissconnected but it happened now in last few weeks 2-3 times that during usage wire dissconnects from vibrations I guess. Very frustrating spec when I was playing in VR and just all of a sudden stick goes limp.

DDuraCell Any tips for my question for ac adapter disconnecting easily. Am I the only one ...

walmis•4/2/24, 2:50 PM

Can you make a short vid demonstrating how loose it is?

mark turner•4/2/24, 3:59 PM

Is there a way to offset the grip slightly ( twist it slightly to the left to allow for me mounting it centrally and using my right hand ) In my other simpit, I was using an extension and could turn it using that. In this pit, I am not using an extension. I cant angle the base either due to using the mounting plate which sits at a right angle on a cross member.

Fr4Ged•4/2/24, 4:42 PM

depends on the grip I guess.
you can fasten the Virpil Constellation Alpha however you want to

DuraCellOP•4/2/24, 6:16 PM

Wwalmis Can you make a short vid demonstrating how loose it is?

DuraCellOP•4/2/24, 6:16 PM

Here is is

Fierce_Fire•4/2/24, 6:33 PM

isnt that not in all the way?

Fr4Ged•4/2/24, 6:34 PM

my cable isn't that much different. my plug goes in 3/4 of they way but it does not wiggle that much.
I did not force wiggle it like you did though.

DuraCellOP•4/2/24, 6:37 PM

it is all the way in

Fr4Ged•4/2/24, 6:38 PM

exactly

Fr4Ged•4/2/24, 6:39 PM

your connector looks to be worn out a bit though.
did you pull the cord or something?

DuraCellOP•4/2/24, 6:40 PM

there is around 3 mm more but I cant put it in more and it just slides out easily and wiggles like that from day 1, thought that is weird from the start but started bothering me now once it dissconect during play even tough I secured the wire so it dosen't get pulled

DuraCellOP•4/2/24, 6:41 PM

if it looks worn its only looks like that in vid it is pristine

FFr4Ged your connector looks to be worn out a bit though. did you pull the cord or somet...

DuraCellOP•4/2/24, 6:42 PM

where does connector looks worn?

DuraCellOP•4/2/24, 6:43 PM

As I said it is same feeling of connection from day 1

DuraCellOP•4/2/24, 6:43 PM

it is not all the way in, wiggles and slides out easily

Fr4Ged•4/2/24, 6:44 PM

the socket has some metal springs keeping the plug tight. mine does not wiggle that much.
but you are as deep in as possible.
the plug is just longer than the socket is.

Number481•4/2/24, 6:48 PM

looks like these little spring tabs need to be bent back out a little to create some tension on the outer plug barrel

DuraCellOP•4/2/24, 6:53 PM

So Should I try and bend them a bit?

Number481•4/2/24, 6:56 PM

its what I would try... but I've also never been a very good role model so....

DuraCellOP•4/2/24, 7:00 PM

Ok helped a bit I think still loose but less slidy feel I think It will be fine will see after some testing.

Vitalii Muravytskyi•4/2/24, 7:56 PM

Hi @walmis , I have received a DIY kit and trying to connect everything together. WebUSB connects well and I can move a point (one axis is reversed) but Configurator app says USB: Disconnected and both motors offline. Tried a different cable - no luck. Joystick is detected by Windows once I plug the USB in.

smitty•4/2/24, 8:10 PM

did you hook up 20V power?

VVitalii Muravytskyi Hi @walmis , I have received a DIY kit and trying to connect everything together...

walmis•4/2/24, 8:11 PM

Sounds like windows serial driver is not functioning. Which Windows version are you using?

Wwalmis Sounds like windows serial driver is not functioning. Which Windows version are ...

Vitalii Muravytskyi•4/2/24, 8:23 PM

I use Win10, 20V Power is connected
Weird, but I can even bind controls in Condor2 sim to Rhino

Vitalii Muravytskyi•4/2/24, 9:15 PM

After creating and executing .bat file for launching with

-serial

-serial

option everything seems fine now.

Mmark turner I had to unclip the connector to lift the plate out enough to rotate it.....

OZ67•4/3/24, 9:18 AM

I just turned the plug around on the stick not the Rhino base , but that was with thrustmaster, yours maybe different situation.

NNumber481 Were you able to get the new version started with only the pedals selected in th...

yzhanping•4/3/24, 12:04 PM

This method is really good and solved my problem. Now the software is working fine

BigBANGtheory•4/3/24, 4:56 PM

hey everyone I came across an issue today in DCS Apache (could relate to other modules) with the force trim... what I noticed is if I set an axis tune S curve on the cyclic it messes with the FFB effects when you trim release (set a new trim position). The joystick and ffb want to return your stick to the centre by a small amount, the physical centre not the trimmed position. When I remove the curves within DCS to linear the Rhino and ffb behaves as I would expect with the spring accepting the new centre.... Is this normal or am I doing something wrong?

BBigBANGtheory hey everyone I came across an issue today in DCS Apache (could relate to other m...

Number481•4/3/24, 5:23 PM

it is normal. Axis curves are not compatible with FFB

BigBANGtheory•4/3/24, 8:26 PM

ty @Number481 that is very useful information

plehmann•4/4/24, 1:14 AM

not too sure if this is the correct channel ...but...

plehmann•4/4/24, 1:14 AM

DEfender just spazzed out and nuked telemffb

plehmann•4/4/24, 1:15 AM

plehmann•4/4/24, 1:17 AM

another in a long line of defender sapazzes I guess from praydog UEVR and github trojans its all been a bit of a mess recently ( praydog takes pancake games to VR in openXR) really cool...but I digress... anyone else have this happen ? I've put and exclusion now into defender for the telem location.

Pplehmann DEfender just spazzed out and nuked telemffb

Number481•4/4/24, 1:24 AM

Looks like a windows secure update today is now flagging the latest build. Was fine this morning.

Adding an exception for your TelemFFB folder as you did, while less than ideal, is the only real solution….

plehmann•4/4/24, 1:24 AM

cue the influx of why is telem not loading anymore !!

plehmann•4/4/24, 2:54 AM

aaan just saw the same post in general before me

plehmann•4/4/24, 3:07 AM

ok so received my second ffb kit the other day and plugged the ol girl in... for a connectivity test.

plehmann•4/4/24, 3:09 AM

so some ignoirant q's inbound that I've not been able to find in the manual or online... I get that there is a different id to ...well id the controller but no idea how to set this up either from telemffb or onmfigurator

plehmann•4/4/24, 3:09 AM

I've got the tlemeffb to spawn another isntance of the ffb app

plehmann•4/4/24, 3:10 AM

plehmann•4/4/24, 3:10 AM

but note the error bottom right

plehmann•4/4/24, 3:10 AM

second controller is seen on com4

plehmann•4/4/24, 3:10 AM

plehmann•4/4/24, 3:11 AM

aand motor goes smooth from notchy so motor and board seem to be ok

plehmann•4/4/24, 3:12 AM

though its only connected via the pwr cables so far - shoul there be other connections too between the board and motor.. there was also a 2 pin 'jst' connector for a 485 connection ? arduino?

Number481•4/4/24, 3:14 AM

You need to set it up in configurator with a different usb PID. It will probably be 2055 by default )same as rhino)

plehmann•4/4/24, 3:14 AM

so I'll need to unplug current rhino??

Number481•4/4/24, 3:17 AM

You should see two options when you start configurator, but if they are both 2055, you will only be able to tell them apart by the s/n. Simpler to unplug the rhino probably

Any tips for my question for ac adapter disconnecting easily. Am I the only one with this issue as t

Similar Threads