if i open in other software programs to display the joystick output the same things are happening
if i open in other software programs to display the joystick output the same things are happening
P
Pthis guy uses vfx also and worked fine 7 months ago
Ptry older configurator
Pthat can be also because of the configurator. I meant we are not sure that it is because of grip itself
Mi am installing 1.0.6
Pgood
M
Mwelp that's not gonna happen, ill need a newer version
Pomg
Pdo you have other pc?
Malright i tried th older one
Mno, i don't
Phow is it with older one
Msame
Pso it is possible that grip itself has problem
Myes or something is odd in the software
Plastly change usb cable
Pif it is same, nothing we can do for now
Pbetter to wait for wall miss
Pchange usb port too
Mi already swapped usb cables and usb ports. no change
Mdid that about 20 minutes ago
Pso letβs wait for wall miss and be ready to contact virpil
FHow's buttons on grip? Are they works well?
Mi wonder if there is an issue where, i need to have a virpil base to configure this joystick axis or program it or something, and without the virpil base, i can't go any further with the virpil grip
Msince the virpil software doesn't recognize the rhino base
Mevery other button and every other axis seems to work fine
Mdoes anyone else's rhino have the X axis inverted, even though the e-stop is facing them ?
οΏ½I have the same problem and have been told that we have to wait for a new version of the firmware. The current 64 button grip setting does not work.
RAh ok. So I'm not doing anything wrong, and it's not something we can program ourselves?
Mwell the good news is that once i get rudder pedals, i don't have to worry about the stupid twist axis
Mwhat is this i'm reading about force feedback rudder pedals?
Mok so here's another question. i am flying the f-14. when i first start the mission / hit pause / break to start, the stick shoots way forward, and i have to trim like crazy to get it to feel sort of neutral, but it is almost impossible to start a mission flying level. what am i doing wrong?
on the good side of things, i successfully took 2000lbs of fuel from the kc135, which is the first time i have ever successfully taken fuel. so the feel this stick provides is incredible
on the good side of things, i successfully took 2000lbs of fuel from the kc135, which is the first time i have ever successfully taken fuel. so the feel this stick provides is incredible
οΏ½I don't believe there is... @walmis any eta on new firmware that will support all the buttons on RealSimulator grips?
Athe F14 naturally pushes the stick forward, that's the way the jet works, probably a big reason the aircraft pitches forward is that you probably need a bit of trim and some throttle to stabilize things
A(in fact -- a big part of the F14 is that it'll move the center around quite a bit based on trim), but neutral trim does start with the stick pitched forward a good amount
Awhich mostly matches what the stick is doing visually in game too
WLooks like the VFX grip (maybe new grip revision?) has indeed larger register than 16bits for twist axis. Could you enable the 
Generic grip (debug) and record the debug tab activity like you did with the raw value, I'll implement this 
Nseems to, but there's also no way I can possibly turn it the full amount by hand, when it's at normal spring force
Nand the grindiness mostly happens at the extremes
NI did have a mini aha moment, in that I realized that sometimes I am recalibrating incorrectly (and treating the throw limiter range as full range), so maybe increased force over a smaller area exacerbates it
Nbut proper calibration doesn't make the issue ever go away, so I'm afraid I haven't really gone anywhere on this issue despite giving it the parts cannon treatment
HCogging torque of electrical motors is the torque due to the interaction between the permanent magnets of the rotor and the stator slots of a permanent magnet machine. It is also known as detent or no-current torque. This torque is position dependent and its periodicity per revolution depends on the number of magnetic poles and the number of tee...
TYou can also DIY rudder pedals
TThis is the F16 set based on the crosswinds 
No you canβt add FFB to 3d printed pedals.
No you canβt add FFB to 3d printed pedals.
FAfter 2 months with the Rhino, I am still confused about many settings. I am using MSFS, X-Plane and DCS with helis and planes. I am looking for configuration files for certain aircraft, which proved to be "realistic". I saw them somewhere, but cannot find them anymore. Where can I find them?
TThere is a section for sharing profiles on the discord
TItβs under βknowledge baseβ
FI found it. Thank you!
FOne other thing I noted when flying: The periodic effects seem to change every 10 seconds. The heli goes brrrrrmmmmmmm... (feels good!) and after 10 seconds drrtdrrtdrrtdrrt (feels strange!) for 10 seconds and then back to brrrrrrmmmmmmmm... and so on. This also happens to other aircraft. Can I change this somewhere?