WYou need to get back and update the firmware now, see if the Web page now allows to update after the powershell fix
IIt does not allow the update
WDid you replug USB and/or reboot ?
IYes
Ieven rebooted
IDid it again now works
IUpdated to latest firmware and software, so in fan control you recommend I setup the fans to start earlier at lower temps?
I
Iwhat settings would you recommend here?
IAre there instructions on how this works? I assume its about controls getting stiffer at higher speeds?
I
WIf you raise the upper end, you'll get twice the stiffness. The purple columns show the current state of spring gain/stiffness.
IGot it, thanks
I
II use this brake lever or the Spitfire and Mosquito, in DCS the hand brake is super sensitive, is there a recommended setting that will make this lever operated brake less sensitive?
IReduce max value reduces travel or brake strenght?
T@I/JG7_Moto may need to set a curve in dcs control in game
Tfor brake lever
IBrake lever is not recognized as an Axis in DCS, which is the problem, its like an ON OFF button, no option to tune it as far as I know
Nsure about that? It's RZ on my Alpha...
IWill try to manually select Rz , good idea, thanks
RThis is a cool new option. I was wondering, is there enough room currently in the Rhino design to install a better fan that might improve cooling even more?
HThere are ways to design your own panels for 3D printing. I actually installed a Phanteks T30. But don’t expect to much. The Motor-Housing is a good heatsink due to its thermal mass - until it is saturated, then it gets difficult to cool, because it has very little surface area compared to its thermal mass. More airflow is always better, but not by much when the heat transfer is poor.
I‘m actually thinking about adding some of those to the motors:
I‘m actually thinking about adding some of those to the motors:
HIf cooling becomes a factor though strongly depends on your kind of flying. Mainly an issue in dogfighting with aircraft that can hold a lot of G for a prolonged time…. No factor in basic flying, Air to ground or helicopters.
Si found the M.2 heatsinks fit very well
RTHe F-14 in dogfights heats the motors up very quickly I found. I I'll have to see if I can find heatsinks that are the right size for the motors. I have one that I thermal taped to the back of a GPU backplate a few years ago that might be too big.
IWhere do you think of attaching the M.2 heatsinks, outside on the case? or internally?
IIf we put one of these outside, pushing air or extracting air from the case ,will it help?
I120mm 5V USB Powered PC Router Fan with Speed Controller High Airflow Cooling Fan for Router Modem Receiver DVR Playstation TV Box and Other Electronics
I
HDirectly on the motors. Otherwise they would have no effect. You need five heatsinks per Motor 4 on the sides and one on the bottom. (Well, you don’t NEED, but that would have the greatest effect)
HNot much.
IGood idea
HMind you, that I have no idea, how much of an effect that would have. I haven’t done that so far.
BAnd then you should submerge it all in a tank of mineral oil that is cooled to sub ambient through a radiator you stick in a freezer.
RThis one is probably too big
BThat honestly looks as if its meant to be cut to fit whatever you need.
DHello everyone!
I've been experiencing a problem for 1 week and everything leads me to believe that there is a bug between the Hype-H145 liveries and TelemFFB.
Let me explain my problem:
15 days ago, no (0) problems with my H145 liveries. Everything worked perfectly with TelemFFB. All settings were done and no problems. Pure joy.
BUT since updating the VPForce software (config + telemFFB), I've had 1 very strange problem.
My livery n°1 works perfectly (MSFS settings, H145 tablet, telemFFB, etc...).
I go back to the MSFS main menu, change the livery (livery n°2) and launch the game.
Now I've got a problem that's been bugging me ever since... I keep getting “Hands ON” on the H145 (whether with the AP or just by moving the collective). What's worse is that the VMS/CTRL doesn't show any (0) game (sim input) or joystick movement (user input)... The only way to cancel it is to do a trim release and after 5-10 sec, the HANDS ON reappears even though I'm doing nothing!
I just don't get it!
I restart the game with my livery n°1 and 0 problems.
I'm familiar with the whole process with the H145 (TR, AP, MSFS keyboard bindings, H145 tablet,...) but I can't see where it's bugging! All my bindings are OK, the H145 tablet is OK, TelemFFB seems OK (I don't see any difference between my 2 deliveries...except the profile name => same settings).
I've recalibrated everything in VPForce config, saved my settings, checked the links everywhere... I just don't get it.
HELP
I've been experiencing a problem for 1 week and everything leads me to believe that there is a bug between the Hype-H145 liveries and TelemFFB.
Let me explain my problem:
15 days ago, no (0) problems with my H145 liveries. Everything worked perfectly with TelemFFB. All settings were done and no problems. Pure joy.
BUT since updating the VPForce software (config + telemFFB), I've had 1 very strange problem.
My livery n°1 works perfectly (MSFS settings, H145 tablet, telemFFB, etc...).
I go back to the MSFS main menu, change the livery (livery n°2) and launch the game.
Now I've got a problem that's been bugging me ever since... I keep getting “Hands ON” on the H145 (whether with the AP or just by moving the collective). What's worse is that the VMS/CTRL doesn't show any (0) game (sim input) or joystick movement (user input)... The only way to cancel it is to do a trim release and after 5-10 sec, the HANDS ON reappears even though I'm doing nothing!
I just don't get it!
I restart the game with my livery n°1 and 0 problems.
I'm familiar with the whole process with the H145 (TR, AP, MSFS keyboard bindings, H145 tablet,...) but I can't see where it's bugging! All my bindings are OK, the H145 tablet is OK, TelemFFB seems OK (I don't see any difference between my 2 deliveries...except the profile name => same settings).
I've recalibrated everything in VPForce config, saved my settings, checked the links everywhere... I just don't get it.
HELP
D(same message in H145 discord/submenu)
NIs TelemFFB loading a different profile for the 2nd livery or is it using the same default one that matches the
Airbus H145.* string?DIt loads a 2nd profile.
Livery 1 = profile 1 (full name of the livery)
Livery 2 = profile 2 (H145.*).
However, I have the impression that I've set them up the same way.
Livery 1 = profile 1 (full name of the livery)
Livery 2 = profile 2 (H145.*).
However, I have the impression that I've set them up the same way.
NIt’s super important that you clone the profile for the 2nd livery from the built-in default as opposed to just creating a new profile and assigning the “HPG” type to it.
It’s one of the limitation how we’re doing dynamic simvar subscriptions for special cases like the Hype helis that I haven’t gotten around to addressing yet.
Alternatively, if you change the “name” in your 2nd livery aircraft.cfg file to start with “Airbus H145”, it should pick up and use the built in profile.
It’s one of the limitation how we’re doing dynamic simvar subscriptions for special cases like the Hype helis that I haven’t gotten around to addressing yet.
Alternatively, if you change the “name” in your 2nd livery aircraft.cfg file to start with “Airbus H145”, it should pick up and use the built in profile.
DOk i try that !
Tis it possible to make throw limiter X Axis -13 deg but +19 deg and Y axis 16 deg? I would like less pull and more push and my stick.
IUpdated firmware and latest Telem,, all good but now my spring settings are controlled by application (DCS) and again in the WWII warbirds the aileron forces are a lot stronger than elevator forces, I modified spring to make it equal, but now its being overridden by DCS, is there a way to make the elevator pitch forces stronger
I
IThe way it is with stiff ailerons and soft elevator is pretty unrealistic.
IUsed to work great before
Tcheck the sticky option?
ASpring forces were always controlled by the game unless you have sticky checked, but doing so would also end up disabling things like trim following. Perhaps some telemffb settings changed in the update you did?