Check Export.lua and disable other tools in there to check if there are incompatibilities.
Check Export.lua and disable other tools in there to check if there are incompatibilities.
TI'll check. Not sure if it matters but if I start TelemFFB after I'm already in the plane it works great. My DCS is a clean load too, just reloaded my computer yesterday.
TOnly thing I'm seeing in my scripts folder is SimHaptic and TelemFFB
MWill do thanks - thought I followed the steps, but perhaps left out the apply after calibration and unlink....
VIm having some trouble with the vpforce winwing adapter. The vpforce app detects the adapter when I select it, but all buttons on the winwing grip are constantly pressed and dont work. Suggestions?
MHi, OK, tried this again, and having similar issues I use a virpil Z extension on both my Rhinos, and when I have the stick at centre or forward of centre, I can adjust the negative balance spring value (approx 11%) to make it stay in a placed position. But if go backwards past the centre, then the stick wont stay where you put it - even at 100% negative..of course at this setting, once I place the stick anywhere past centre in the forwards direction, it snaps fully forwards.
MAnother thing I notcied on calibration ( but not in normal use) is that when you rotate the stick around the circle at full deflection, there are places where I am feeling a cogging ( forwards) and other places ( around 4 oclock and 8 oclock) where I can feel a notching....any ideas whats going on there?
M
MA video may a little large to post
Mand with my normal effects applied
HThe first screen shot you show the balance spring at -94% in the forward postion 6% in the positive but your 2nd screen shot your balance spring shows -11.1% and 0%..Your left and right is also changed. On my forward position I'm using 18% (positive number) and rear 5%, 12% on my left and 10% on my right. As for cogging this usually means the calibration ones done properly to full deflection or there is a mechanical issue.
CHey,
Outside dimensions are perfect but the inside hole for the din is way too big. Would you still have the CAD for this?
Outside dimensions are perfect but the inside hole for the din is way too big. Would you still have the CAD for this?
MSadly, I could not find my original openscad project, but I re-measured the original adapeter plate, and the inside diameter was 10mm, so I used 3D builder to fill the oversized hole, then put a 10mm hole with a slight chamfer as per the original plate. this should be much closer.
WWAdapterConnector-matev2.stl923.23KB
TSome of my planes in IL2 Great Battles the center is forward or the trim is acting very weird if I trim nose down the stick moves forward alot in order to keep plane level. I need to apply constant force down when doing so. But some of my planes do not act like this I'm using the same config profile for all right now. any thoughts? I notice this on the duck the spit and the p39 so far I know it happens on other but those are the ones I've flown recently.
Tit like trim is working but why is it having the opposite effect on the direction of my stick like this?
KDo you have configured curves in IL-2? This lead to the problem on my side.
Tno curves in IL2 at all
Nnot sure I fully understand your problem description, but if the trim movement seems to be backwards, in general I would recommend to make sure the dot in the axis view in the configurator app moves in sync with your joystick. If one or both axes are backwards, use the invert setting for that axis in configurator.
If your axis is backwards and you invert it in the game, this will usually lead to inverted forces since there is typically no sync between "ffb direction" and "axis direction".
If your axis is backwards and you invert it in the game, this will usually lead to inverted forces since there is typically no sync between "ffb direction" and "axis direction".
TI have turned my stick base around but I checked the invert on my pitch axis when I turned my base around. Is there another area I need to invert for trim to work correctly.
T
Twhat you are saying makes sense my stick works good for everything but when trimming plane out the stick moves the wrong direction
TI just don't know how to fix it.
Ndoes the purple dot follow the stick correctly and in the right direction?
Tyes the purple follows
Tits kinda weird when i trim out plane stick needs to be forward to stay level?
Tonly in a few planes
NI guess I misunderstood then? Thats how the trim effect works. If you trim down, the stick will move forward, same for other directions.. the center point of the spring effect will move in the direction you are trimming.
If nose down trim is required to maintain level flight, the stick will be forward of center.
If nose down trim is required to maintain level flight, the stick will be forward of center.
Tyes maybe these planes are just weird to me and the FFB is weird to me as well never used it before but some planes act different most planes i can trim out and stick stays in middle level flight few planes stick must be well forward in level flight while trim is 100
NI can't really help with what to expect from various aircraft in IL2, but that is how FFB trimming works in general. Various aircraft my implement it differently or not at all.
Tyeah I think some of these planes are just really nose light and flying at high speed even with full trim nose down the nose wants to raise
VSome planes simply dont have a pitch trim, like the IL2 itself and i-16 (presumably they didnt have one IRL). If you want, you can "cheat" and use vpforce configurator to implement hardware force trim (using trim controls defined there). Some planes in Il2 require excessive nose down trimming with flaps down.
MHi, the last screenshot with the other effects checked is what I have now, the first shot was when I was trying extremes of the slider to see what happens.
HI wish I could help further. I tried multiple tests and grip lengths and didn't have an issue setting up based on my own video and what F14 Billy recommended as in the process. Maybe you have an issue with your unit. How did you build your unit, is it pre-built etc? May have to reach out to the devs and tag them
MHi, thanks, it was pre built and seems to work fine apart from not behaving as you describe in the video!
HIf you have a pre built rhino by walmis then definitely reach out to him
WYou have a decently steep spring gain map applied. I've loaded your config and tuned the filters a bit, works reasonably well at high pot gain (the attached .vpconf file will only patch the filter values so you can apply it on top of your current profiles)
R@mark turner what is the reason you have such a steep spring gain? I’ve tried steep spring gains to make the centering stronger for holding the long extension but I get reverberations still.
1It appears my ingame Trim control for dcs is no longer working. Not sure when it happened as I’ve been using hardware trim for helicopters and haven’t been in a fixed wing for a while so I haven’t noticed the issue until now. Has anyone ran into this or have any ideas as to what the issue could be?
Nmake sure you uncheck both "sticky" spring and "override trim" in configurator. Beyond that, its just simply binding the trim controls in DCS (and the normal stuff like making sure FFB is enabled globally)
WAlso check dcs.log, if it lists vJoy input device it could cause problems with trim
1Nothing is checked and also turned off telemffb to be double sure…. Thank you for the answer!
1I will check that, thanks!
1i did find this in the logs
02 19:21:39.194 INFO INPUT (Main): created [vJoy Device] with full id [vJoy Device {6BE6F3E0-7745-11ed-8002-444553540000}], ForceFeedBack: yes, guidFFDriver: {EEC6993A-B3FD-11d2-A916-00C04FB98638}
02 19:21:39.194 INFO INPUT (Main): created [vJoy Device] with full id [vJoy Device {6BE6F3E0-7745-11ed-8002-444553540000}], ForceFeedBack: yes, guidFFDriver: {EEC6993A-B3FD-11d2-A916-00C04FB98638}
1Still having the issue...
i removed the vjoy device, no longer appears in logs,.
no effects are sticky in vpconfig
there are no curves or saturation in the axis within dcs
nothing that i can see in telemffb whould be causing it but i closed it just in case and it still will not trim.
when i hold the trimmer button the spring force is removed but it will not hold the new trimmer position
the trimmer mode is in either default or instant if "ffb friendly" is present
global ffb is checked in dcs
this is challenging my patience!
i removed the vjoy device, no longer appears in logs,.
no effects are sticky in vpconfig
there are no curves or saturation in the axis within dcs
nothing that i can see in telemffb whould be causing it but i closed it just in case and it still will not trim.
when i hold the trimmer button the spring force is removed but it will not hold the new trimmer position
the trimmer mode is in either default or instant if "ffb friendly" is present
global ffb is checked in dcs
this is challenging my patience!
WSee the thread here: https://discord.com/channels/965234441511383080/1230852705593851964/1324122150206050344
someone had the same issue, check the points outlined in the thread
someone had the same issue, check the points outlined in the thread
WThe trim (blue circle) indicator should jump to the trimmed position:
1i updated/reupdated everything to do with vpforce and the problem seems to have fixed itself!!
MThis is to make the stick feel harder to pull the more I pull it….I wanted some appreciable resistance at around 3 or 4 G which is commonly used for most tactical turns.
MBy the way, I am also suffering with oscillations around the centre and despite some hours of tinkering, not managed to isolate any settings which help.
MGoing to try Walmis settings above
MIt would be good to know exactly what causes it….Last year when I had the issue again, Walmis advised reducing damping voltage - but this time adjusting those settings seemed to make no difference. I will check now with the supplied .conf file