Rat Rig Community [Unofficial]•2mo ago

Trouble installing RatOS, configured Octopus v1.1 board but consistent error message

Hello, just installed RatOS and want to finish configuring the main board but keep encountering this error with Klipper. Tried reflashing the board and updating anything I can but still no luck, would appreciate any input!

22 Replies

strexcorpOP•2mo ago

update: ratos command isnt working on the pi so there's some form of packet that's not there

TheTik•2mo ago

Did you try copying over an old printer.cfg or anything? Missing files suggests the install didn't complete or something

strexcorpOP•2mo ago

no, is there a specific version I should copy over?

TheTik•2mo ago

no, just trying to think of how the include could fail I'd reinstall ratos again, something went terribly wrong. Did you use something other than the default username/password?

strexcorpOP•2mo ago

nope, just used the generic user/pw I'll try reinstalling though when i tried installing 2 different older versions, i either got an error reading unable to connect to moonraker or the system fully being unable to find firmware 64 bit version was unable to find firmware, 32 bit was unable to connect to moonraker

TheTik•2mo ago

Older version of what?

strexcorpOP•2mo ago

ratos, i tried installing the rc1 version got the same moonraker disconnect error regardless of which version of 32bit rat os i installed

strexcorpOP•2mo ago

TheTik•2mo ago

Have you tried connecting via the web interface? And id only install the latest

strexcorpOP•2mo ago

how can i do that? the ratos hotspot does not show up?

TheTik•2mo ago

That's another serious issue then. Something is fucky

strexcorpOP•2mo ago

yeah i figured think it might be a problem with the sd card? so im reinstalling the current version of ratos

strexcorpOP•2mo ago

the hotspot is showing up so i can at least open mainsail web but i still get this error

strexcorpOP•2mo ago

running the most recent ratos 32bit

TheTik•2mo ago

link your printer.cfg? Actually, scratch that. Do this:

1. Flash image
2. Connect to hotspot
3. Setup wifi through configurator (and let it reboot)
4. Go to /config
5. Refresh update manager
6. at this point nothing should be invalid, all green. IF THAT'S NOT THE CASE stop here and post your moonraker.log
7. Update only the RatOS package(NOT configurator).
8. Update RatOS configurator (this takes awhile, if the mainsail output of the update process hangs, let it sit for 10 minutes and then refresh the page, Ctrl+Shift+R)
9. Restart moonraker service (click power icon in the top right of mainsail, click the refresh button next to moonraker under "service controls")
10. Reload mainsail (Ctrol+Shift+R)
11. Refresh update manager
12. "RatOS" should be gone from the list. Everything should be green and have several updates except RatOS configurator (ignore the klipper errors). If it's not, stop here and post your moonraker.log.
13. Click update all.
14. Done.

1. Flash image
2. Connect to hotspot
3. Setup wifi through configurator (and let it reboot)
4. Go to /config
5. Refresh update manager
6. at this point nothing should be invalid, all green. IF THAT'S NOT THE CASE stop here and post your moonraker.log
7. Update only the RatOS package(NOT configurator).
8. Update RatOS configurator (this takes awhile, if the mainsail output of the update process hangs, let it sit for 10 minutes and then refresh the page, Ctrl+Shift+R)
9. Restart moonraker service (click power icon in the top right of mainsail, click the refresh button next to moonraker under "service controls")
10. Reload mainsail (Ctrol+Shift+R)
11. Refresh update manager
12. "RatOS" should be gone from the list. Everything should be green and have several updates except RatOS configurator (ignore the klipper errors). If it's not, stop here and post your moonraker.log.
13. Click update all.
14. Done.

strexcorpOP•2mo ago

did all of that and ended up with this error

TheTik•2mo ago

bizarre. Try a different SD card?

strexcorpOP•2mo ago

install ratos to a different sd card? okay tried a different sd, got the same bed mesh error, and tried following these steps but got invalid updates

strexcorpOP•2mo ago

moonraker.log

TheTik•2mo ago

thats wild. This isn't a part of the process that gives people issues. Maybe try a different internet connection?

strexcorpOP•2mo ago

tried hooking up via ethernet and it seems to be sorted out now thanks !

TheTik•2mo ago

oh thank goodness. That was getting too weird XD

Gaming

Programming

Trouble installing RatOS, configured Octopus v1.1 board but consistent error message

Did you find this page helpful?