Unable to Parse Option 'pid_Kd' in section 'heater_bed'

Really sorry I've had to post so many of these. Hoping this and one other are the last of it.

I went into the config file, uncommented all the ones pertaining to my printer being a 500, and after restarting got this error. I didn't touch this part.

I looked up the specific error and others had the question but no answer.

VauschOP•12/9/22, 5:21 AM

the heater bed section and pid_Kd

sacred-rose•12/9/22, 6:15 AM

The problem is in the next lines, there comes the ADXL section. You probably have one or two lines there still commented

VauschOP•12/9/22, 6:20 AM

VauschOP•12/9/22, 6:21 AM

guessing I gotta uncomment "resonance tester" and probe points?

VauschOP•12/9/22, 6:21 AM

sorry this is my first time using klipper. Y'all are the most helpful community

HHeisenberg@Krähendruck The problem is in the next lines, there comes the ADXL section. You probably hav...

VauschOP•12/9/22, 6:25 AM

Okay uncommented [resonance tester] and got this

sacred-rose•12/9/22, 6:25 AM

Probe points have to be also uncommented

VauschOP•12/9/22, 6:26 AM

and back to the initial error

sacred-rose•12/9/22, 6:26 AM

And the line with adxl has to be commented

VauschOP•12/9/22, 6:26 AM

VauschOP•12/9/22, 6:27 AM

ah!

VauschOP•12/9/22, 6:27 AM

dah, new error

VauschOP•12/9/22, 6:28 AM

Oordinary-sapphire Click to see attachment

sacred-rose•12/9/22, 6:29 AM

That's defined above, you probably still have the corresponding lines commented, I am just on mobile right now so cannot look into the exact line. Best practice would be that you upload your printer.cfg here

VauschOP•12/9/22, 6:30 AM

alright

VauschOP•12/9/22, 6:30 AM

printer.cfg10.87KB

VauschOP•12/9/22, 6:33 AM

ah, found the line

VauschOP•12/9/22, 6:36 AM

And MCU is not able to connect

VVausch Click to see attachment

blacksmithforlife•12/9/22, 1:05 PM

you didn't uncomment line 91

VauschOP•12/9/22, 1:07 PM

I did

VauschOP•12/9/22, 1:07 PM

not in that file but I did find it

blacksmithforlife•12/9/22, 1:08 PM

ok, so what error are you getting now (screenshot) and upload your current printer.cfg

VauschOP•12/9/22, 1:08 PM

VauschOP•12/9/22, 1:08 PM

printer2.cfg10.87KB

VauschOP•12/9/22, 1:09 PM

I do sincerely appreciate the help from y'all and I am sorry I'm not so versed in this. Hardware, I got. Firmware, well there's a reason I didn't continue with computer science in college.

blacksmithforlife•12/9/22, 1:11 PM

and you have a regular octopus board? not octopus pro

VauschOP•12/9/22, 1:11 PM

regular, yes.

blacksmithforlife•12/9/22, 1:12 PM

the printer.cfg looks good to me. I would power it down and unplug everything in case something is shorting the board (triple check your endstop wiring as that is common)

blacksmithforlife•12/9/22, 1:13 PM

then power it back up. It should complain about the ADL temp being out of spec which is normal because your thermistor isn't attached

blacksmithforlife•12/9/22, 1:13 PM

then slowly start plugging stuff back in until you find what is causing the issue

VauschOP•12/9/22, 1:13 PM

yeah definitely had that issue earlier with the endstop. Those wires got quite hot.

I'll start on the wiring.

VVausch yeah definitely had that issue earlier with the endstop. Those wires got quite h...

blacksmithforlife•12/9/22, 1:14 PM

oof, hopefully you didn't fry your board then

VauschOP•12/9/22, 1:14 PM

sure hope not. the lights are all on still

VauschOP•12/9/22, 1:14 PM

and the bltouch gives a click

VVausch sure hope not. the lights are all on still

blacksmithforlife•12/9/22, 1:15 PM

but your endstop ports might be dead

blacksmithforlife•12/9/22, 1:15 PM

that's why there are a bunch of warnings about making sure the endstop wiring is correct

VauschOP•12/9/22, 1:15 PM

yeah, totally see that.

VauschOP•12/9/22, 1:16 PM

one was definitely correct cuz I used an extension wire and had to use a dupont connector.

blacksmithforlife•12/9/22, 1:18 PM

complete tangent - but I will only use an extension on a static wire (i.e. the wire isn't moving around on the toolhead). Most of the wiring that comes with stuff isn't meant to be moved around on a toolhead - so I specifically bought wiring for that

VauschOP•12/9/22, 1:19 PM

I would, but the wire is too short to reach across the full range of the 500.

VauschOP•12/9/22, 1:20 PM

same with the extruder motor.

blacksmithforlife•12/9/22, 1:21 PM

get longer wire then

blacksmithforlife•12/9/22, 1:21 PM

i recommend https://www.igus.com/product/1013?artNr=CF9-03-16-07-03-INI

blacksmithforlife•12/9/22, 1:22 PM

it is made for industrial machines, is self supporting, and has all the various wires you need for your hotend

VauschOP•12/9/22, 1:28 PM

I mean fair. Can't replace the motor but I'll look at it.

blacksmithforlife•12/9/22, 1:51 PM

Why would you need to replace the extruder motor?

VauschOP•12/9/22, 1:53 PM

the wire i mean

blacksmithforlife•12/9/22, 1:54 PM

I just cut my extruder wiring short and added jst-sm connectors

VauschOP•12/9/22, 2:33 PM

okay, took out all the wires save for power and still got the mcu error.

sacred-rose•12/9/22, 2:38 PM

Did you flash the Board with RatOS Firmware?

Unable to Parse Option 'pid_Kd' in section 'heater_bed'

Similar Threads

Similar Threads

Similar Threads