I think we should have a pot to contribute and when it reaches a specific amount, Walmis sends the d

I think we should have a pot to contribute and when it reaches a specific amount, Walmis sends the dev a Rhino so they can iron out their force feedback code

SskyPickle no forces are present on the stick. i have turned spring gain to zero to elimina...

Number481•6/28/23, 2:47 AM

Well, it was worth a shot..glad you figured it out!

Comrade_Weng•6/28/23, 4:24 AM

Using ffb in il2, everything appears to be working great apart from when I use elevator trim. The neutral position of the stick moves as I trim however I get a bit of a jump at some points. I can't quite work out why. Any suggestions please?

kingjamez•6/28/23, 5:10 AM

Check your grub screw on the motor shaft.

Comrade_Weng•6/28/23, 5:17 AM

I have already checked this and it's ok. The best I can describe it is if I wind in full up trim from full down trim. There is a jump, almost as if the stick is catching up to a bit of lag.

Jon (Bounty_V)•6/28/23, 5:39 AM

could it be power related?

Comrade_Weng•6/28/23, 5:43 AM

I doubt it. Am running at 24vdc with a 10amp supply. No issues pulling full continuous amperage during testing.

CComrade_Weng Using ffb in il2, everything appears to be working great apart from when I use e...

walmis•6/28/23, 6:35 AM

Any specific aircraft in IL2 causing this?

Comrade_Weng•6/28/23, 6:58 AM

Good question... I'll do some testing. So far only noticed in the P51.

Comrade_Weng•6/28/23, 10:25 AM

Can confirm that it's not all aircraft. I shall do some more testing to write up a bit more of a comprehensive list.

SskyPickle I think we should have a pot to contribute and when it reaches a specific amount...

PiNKSH!T•6/28/23, 12:51 PM

It's been discussed having a unit made for being sent out to devs for them to use to make their ffb work right.

Anthony•6/28/23, 12:55 PM

Yeah, don’t think it’s beyond the financial means of any reliable dev to cough up that kind of money themselves

NNumber481 Well, it was worth a shot..glad you figured it out!

skyPickleOP•6/28/23, 1:49 PM

This was polychop's reply to my query about that checkbox:

skyPickleOP•6/28/23, 1:49 PM

This checkbox simply changes trim behaviour for FFB sticks, so that the trim position is not accounted for as it would be with a standard centering stick.

skyPickleOP•6/28/23, 1:50 PM

The do not use the DCS FFB checkbox in the general options.

Rob EB•6/28/23, 2:20 PM

@walmis Any more thoughts on the issue I have with reduced X-axis damping?

Not sure if it's related in any way but I adjusted the spring gain map to increase the force gradient closer to the center of the axis (to emulate the double gradient of the F15 stick), and it resulted in a low-ish frequency induced oscillation if the axis were released from deflection. The oscillation occurred on both axis.

Rob EB•6/28/23, 2:21 PM

Couldn't figure out a way to tune it out.

Subsonic•6/28/23, 2:28 PM

filter frequency?

RRob EB @walmis Any more thoughts on the issue I have with reduced X-axis damping? Not...

walmis•6/28/23, 2:31 PM

I've reproduced this, so yeah this is the nature/limitation of system dynamics. You would need to reduce the spring gain to stabilize it. Since reducing the throw range essentially increases the spring gain.
Increasing damper filter frequency would improve this, but this will eventually cause high frequency stability issues.

Rob EB•6/28/23, 2:47 PM

Is the relationship linear? IE, with my x-axis throw range reduced to 11 degrees (50%), would the spring gain need to be reduced to 50% also?

Reed•6/28/23, 3:22 PM

Interesting. Are you using endstops at 50% or throw limiter?

Rob EB•6/28/23, 3:43 PM

throw limiter

Reed•6/28/23, 3:50 PM

Pickles•6/28/23, 11:04 PM

Greetings all. First off I'd like to say this base has been amazing and has served me well over the last 1-2 years. I'm the proud owner of S/N 0001.
Well today after a few weeks of no use I noticed the x axis is sorta of sticking. It was very noticeable in the MI 24 in DCS, but also noticeable not in game. Has this been experienced to any degree? I'm happy to crack it open and perhaps lube/clean some bearings or something if that would help, but I figured it would be smarter to post here first.

PPickles Greetings all. First off I'd like to say this base has been amazing and has serv...

kingjamez•6/29/23, 8:51 AM

Walmis will know better, but i had something similar happen on my DIY kit. It ended up that my thrustmaster grip was not screwed all the way into the top threads and it was rocking back and forth as I moved it. It wasn't obvious because it was so slight.

Comrade_Weng•6/29/23, 12:43 PM

FWIW I am unable to replicate the trim issue I had in il2 with a range of aircraft, including the original P51. I shall keep an eye on it

Comrade_Weng•6/30/23, 6:40 AM

So... after testing various aircraft. I have accidentally reproduced the problem. So far I can reproduce it in the P51D, but only with flaps on a landing approach. Also in the C47 during normal flight. The issues is that I add elevator trim and nothing happens. The manual force to keep the aircraft trimmed increases without the stick centre moving. Then theres a sudden increase in stick centre point to the trimmed position. I suspect that this is an IL2 feature, i mean bug.