Interesting. Can you give some examples which modules do this? (the cases in which it’s better to us
Interesting. Can you give some examples which modules do this? (the cases in which it’s better to use “HW trim + override”
Pi fly ww2, so try p47 and mosquito
MHi Walmis, a couple of weeks back (13th Oct) , you kindly gave me some settings to try to offset the weight of the TM metal grip I was using and to stop the oscillations. They worked great, BUT.......I have decided not to use the grip after a week or so, as I basically need one with more buttons, so swapped in a Virpil Alpha I have. Now, I need to un do those or adjust them to suit the lighter grip. I am going to save a profile for future possible use etc of your settings for the heavy grip. What would you adjust on your advised settings & by how much ( and why if you can explain, as its good to understand what I am doing rather than just blindly do it) to suit the lighter grip? Many thanks for your continued amazing support and customer service.......
PYeah I have a lighter grip also & had some instability that got the x axis motor to self protect, so I'd be kneen to know what to change & why.
HDoes anyone have an idea of what approximate settings need to be used for the 'balance spring' force to balance out a given grip weight on a given extension length?
HOr is it just the 'TFAR' method?
N'try it and find out' is probably a good approach... but I'll just say that the "adaptive recentering" does a fine job by itself with my Alpha Prime grip sitting on a virpil z extension.
HIt did alright with a 100mm extension, now that I'm running a 32cm extension at anything beyond about ~50% of the axis in any direction it's drooping enough that it's screwing up autopilot in multiple aircraft
HSo some extra centering force is going to be needed
HIt also tends to oscillate sometimes, so some tweaks to friction are needed
WMy approach to find the values to balance spring is to disable the regular spring, so the stick is limp. Then increase the balance spring values in each direction and check if stick wants to fall when released at an angle. Once it roughly stays in place where you put it, then you're good to go.
HUsing that method, looks like I need about ~25% for balance spring to counteract most of the droop, which might explain why adaptive recenter wasn't quite cutting it
WYeah, once you apply some balance spring, the adaptive recentering will have more authority and will not saturate as before.
HI'm still running into an issue with oscillation in the X axis that tweaking the damper/friction forces isn't making a dent in
HReducing the spring gain map for the X axis can fix it, but I'm worried that will affect the droop issue in that axis
WCan you show your settings?
HI will when I get some time back at my computer. I'm going to test the settings I have right now and see how it performs, since I reduced the max gain in the X to eliminate the oscillation
Aso i've noticed kind of an interesting issue, that i think my be a software thing, where the spring forces can seem to apply inconsistent force as you move towards the extremities of the movement. it's a bit subtle, but it does show up in my virpl graphs:
Abasically it kinda feel like i hit a small amount of resistance bump before breaking through to the edge, this is close to the outer edge of the movement (this is with 100% spring strength, default gain map
Athe other settings are pretty minimal, although even with them all disabled, it still was an issue (minus spring of course)
Aalso gain map in case you want to see that
Ahere's another example to show that clear change in resistance towards the edge
WHmm, it could be this is because of PSU power limiting - try increasing PSU current limit or reducing max motor current to 25A and see if this goes away
Aincreasing PSU current to 14 does seem to fix it, although i don't know if that is safe?
A(or at least -- vastly reduces it, it might still be there a little bit
WI recommend not exceeding max current of the PSU, otherwise PSU over current shutdowns are to be expected
Awhat's max current of the psu?
W9.5A iirc
Awhat's strange is that it only happens in the X axis, not the Y axis :/
WOr you can reduce max motor amps to 28.
Aso what exactly is happening? out of curiosity?
Wsaturation
A28 motor max and 9.5 psu current do definitely get rid of most of it for sure
Athere's still a bit, but it's much further towards the extremities, which makes it less likely to hit
Ait is weird that the Y axis seems to have not of this prob though
WAlso force compensation could play a role here
Ai definitely have much higher force compensation on the X axis
A150 on X vs 80 on Y
Abut does make me wonder if there's some software level stuff that still could account for this and make it feel better?
Ai definitely need 150 on the X axis, Y axis doesn't need it, not sure why
Aif i drop force compensation down to 80 for the X axis, the problem does go away, but of course, i don't hit the max X value under 100% spring force)
WI did some work on power limiting and force comp for the next firmware, so hopefully it will improve on this
Asick, i look forward to the next christmas drop (and by that i mean, anytime you release a firmware update it's christmas lol)
RNice
RWhen we update the firm are all of the defaults also updated to the current standard?
THey, I just received my Rhino and it feels great to fly in Apache, but I noticed that it slides a bit forward (and stops) when I trim in negative Y position.
How can I fix it? I'm using TM Warthog stick without extensions.
How can I fix it? I'm using TM Warthog stick without extensions.
WHey, you mean it sags a bit forward?
WAlso "adaptive recentering" helps to keep the stick in the trimmed position
TI'll try, thank you
BIs there a variable in TelemFFB to reduce engine rumble in fixed wing aircraft? I only see a switch to turn it on and off in the stock config file.