Hey, I just received my Rhino and it feels great to fly in Apache, but I noticed that it slides a bi

Hey, I just received my Rhino and it feels great to fly in Apache, but I noticed that it slides a bit forward (and stops) when I trim in negative Y position.
How can I fix it? I'm using TM Warthog stick without extensions.

TTimmy Hey, I just received my Rhino and it feels great to fly in Apache, but I noticed...

walmis•10/25/23, 5:56 PM

Hey, you mean it sags a bit forward?

walmis•10/25/23, 5:58 PM

TM grip is quite heavy and you can balance it using the "Balance spring" feature, you can find a discussion here recently: 🧰support

walmis•10/25/23, 5:59 PM

Also "adaptive recentering" helps to keep the stick in the trimmed position

TimmyOP•10/25/23, 5:59 PM

I'll try, thank you

blave549•10/25/23, 9:47 PM

Is there a variable in TelemFFB to reduce engine rumble in fixed wing aircraft? I only see a switch to turn it on and off in the stock config file.

Bblave549 Is there a variable in TelemFFB to reduce engine rumble in fixed wing aircraft? ...

Number481•10/25/23, 10:09 PM

 engine_rumble_lowrpm = 650            
 engine_rumble_lowrpm_intensity = %8     
 engine_rumble_highrpm = 2800        
 engine_rumble_highrpm_intensity = %4

 engine_rumble_lowrpm = 650            
 engine_rumble_lowrpm_intensity = %8     
 engine_rumble_highrpm = 2800        
 engine_rumble_highrpm_intensity = %4

Should work for DCS or MSFS (or IL2).. even if its maybe not in the default sim section

Subsonic•10/26/23, 12:14 AM

So....crazy thing I have seen sine the last DCS update....
Tomcat on deck before launch, wipe out the controls
Pull back on stick at a moderate to high rate....boom!....pitch motor takes a nap and base needs a power cycle to wake up
Odd since the only ffb forces are the basic spring and damper rates.

In flight, a rapid split S, not really slamming the stick aft...smae effect...nap time for pitch. Never an issue in roll.

Outside of DCS...I can whip the stick around and never an issue.

Subsonic•10/26/23, 12:14 AM

Subsonic•10/26/23, 12:15 AM

Does not seem like a current spike.....but maybe it is happening too fast to see in the software?
Thanks for consideration in advance...

A. Palmetto•10/26/23, 3:13 AM

Just sent in an order for the 2x motor kits+usb for a diy setup - are their any other electronics I will need to get that are not included?

Subsonic•10/26/23, 4:18 AM

PSU, 5pin DIN connector for grip, fan, jst connectors...
https://github.com/protomaker964/Rhino-FFB-Clone-3D_Printed/tree/main

GitHub

GitHub - protomaker964/Rhino-FFB-Clone-3D_Printed: 3D print files, ...

3D print files, parts list and instructions to build a DIY version of the Rhino FFB Stick base using the VPForce motor kit - GitHub - protomaker964/Rhino-FFB-Clone-3D_Printed: 3D print files, parts...

Subsonic•10/26/23, 4:18 AM

parts list in the build pdf

SSubsonic So....crazy thing I have seen sine the last DCS update.... Tomcat on deck before...

walmis•10/26/23, 4:46 AM

Do you have telem running? Can you check the fault code once it enters the failed state?

SSubsonic PSU, 5pin DIN connector for grip, fan, jst connectors... https://github.com/prot...

A. Palmetto•10/26/23, 5:16 AM

Thank you! I’m actually looking to use this print! I posted a question about the pullys in the DIY channel I figure it would be a better channel than a support channel for the actual rhino

Wwalmis Do you have telem running? Can you check the fault code once it enters the faile...

Subsonic•10/26/23, 12:28 PM

Dang, forgot about telem, I will give that a look today. Thanks!

blave549•10/26/23, 5:27 PM

Just a note that I ran into something that I'd never seen before in DCS Open Beta (that is almost certainly unrelated to anything Rhino). In the A-10C II, my stick would not work, even though the x/y axes showed up as working in the Control Options dialog. At one point it started working, but then stopped again. I think, but am not sure, that it's specific to the Hawg. I tried a couple other aircraft and they were fine.

Wwalmis Do you have telem running? Can you check the fault code once it enters the faile...

Subsonic•10/27/23, 1:39 PM

Good morning (afternoon for you I think),
SO I ran Telem and did some testing.
When I can induce the shutdown, nothing shows in telemetry.
So I messed around with the max gain pot and lowered it some and no pitch shutdown on faster pulls.
Certainly seems related to effect intensity and just the pitch motor shutting down.
Do you think this is maybe power supply related? I was thinking not since the roll motor stays active.
Could this be a motor current issue and will the max current setting in the software help? Though it is set to 25A and the PSU is not gonna push that much.
Keeping max gain turn down a bit seems to keep it all in check, but I would love to get back to the strength settings I had if possible.
Thanks!

SSubsonic Good morning (afternoon for you I think), SO I ran Telem and did some testing. W...

walmis•10/27/23, 1:44 PM

A motor fault code would be useful here, it's displayed in the status bar (OK when operational)

Subsonic•10/27/23, 1:50 PM

ahh in the status bar ok...since in the main telem screen I saw nothing but the normal connections ok, effects on, and the power reset.
In this status bar?

Subsonic•10/27/23, 1:50 PM

walmis•10/27/23, 2:04 PM

No, at the bottom:

walmis•10/27/23, 2:04 PM

It will show a fault code if the motor shuts down with a long beep

Subsonic•10/27/23, 2:06 PM

Got it thanks

TimmyOP•10/27/23, 2:18 PM

If I set the pot function as Spring Gain, does it mean that at 100% pot value the spring effect would be at 30% according to the settings below?

smitty•10/27/23, 2:26 PM

yep the knob goes to that max setting

Snooper•10/27/23, 3:38 PM

hello, why in msfs flying th a2a comanche, I'm seeing the yoke moving but that is not reproduced in the rhino?

smitty•10/27/23, 3:47 PM

what kind of movement are you seeing? is this with or without autopilot

SSnooper hello, why in msfs flying th a2a comanche, I'm seeing the yoke moving but that ...

Number481•10/27/23, 4:09 PM

You gotta give us more info.. Are you using TelemFFB? Are you using the latest version which adds trim/AP following support? Have you set up the trim/ap following per the TelemFFB section in the VPforce manual?

Snooper•10/27/23, 5:03 PM

yes yes and yes

Snooper•10/27/23, 5:04 PM

I have it this way:

Snooper•10/27/23, 5:04 PM

#############################
##### MSFS Specific Defaults
#############################
telemffb_controls_axes = True
trim_following = True
ap_following = True

Snooper•10/27/23, 5:04 PM

in the config.ini

SSnooper yes yes and yes

Number481•10/27/23, 5:11 PM

Another quite important question... Do you have 'sticky spring' enabled in VPf Configurator?

Snooper•10/27/23, 5:19 PM

let me check

Snooper•10/27/23, 5:19 PM

Snooper•10/27/23, 5:20 PM

SSnooper no

Number481•10/27/23, 5:25 PM

Did you unbind your axes in MSFS? Sorry.. just going through the common issue causes

Snooper•10/27/23, 5:26 PM

yes I did

Snooper•10/27/23, 5:27 PM

I felt like it was for nothing, but I did. or felt like I did it someway wrong

Snooper•10/27/23, 5:27 PM

just cleared the bind and assign it back again as it was..

Number481•10/27/23, 5:29 PM

what does your comanche settings look like in your telemffb config?

Number481•10/27/23, 5:30 PM

last thing would be to drop a copy of your TelemFFB log file in here for me to look at.

Snooper•10/27/23, 5:30 PM

I think I have nothing specific for it

Snooper•10/27/23, 5:31 PM

config.ini24.32KB

Snooper•10/27/23, 5:33 PM

if you have some specific for the comanche that would be awesome

Snooper•10/27/23, 5:33 PM

and thanks!!

SSnooper Click to see attachment

Number481•10/27/23, 5:35 PM

This looks like maybe an old copy of the default config.ini? The default for the latest TelemFFB has the a2a pa-24 (comanche) in it already

Number481•10/27/23, 5:36 PM

Without a specific aircraft section telling TelemFFB that the aircraft is a "PropellerAircraft".. things won't work right.

Snooper•10/27/23, 5:36 PM

ok.. all update and check if it has the comanche config part

Hey, I just received my Rhino and it feels great to fly in Apache, but I noticed that it slides a bi

Similar Threads

Similar Threads

Similar Threads