seems to work fine for me.. best advice I can give s to startup without your userconfig (aircraft w

seems to work fine for me.. best advice I can give s to startup without your userconfig (aircraft will just be detected as "generic aircraft)... if that works, look at your userconfig for syntax errors ( duplicate

[setion names]

[setion names]

[setion names]

[setion names] or missing

[ ]

[ ]

[ ]

[ ] or duplicate line items in a given section.

Number481OP•11/3/23, 7:31 PM

What conditions did the error occur under? Starup of TelemFFB? Loading the Aircraft with TelemFFB already running? Mid-flight?

Reign•11/3/23, 9:34 PM

Hello, has anyone had an issue with a "clicky" sound when passing through the X axis?

Reign•11/3/23, 9:51 PM

It occurs when unpowered, powered, and also occurs if I hold the stick back and to the right when under load:

Reign•11/3/23, 9:52 PM

NNumber481 seems to work fine for me.. best advice I can give s to startup without your us...

Snooper•11/3/23, 11:40 PM

I never "tampered" with the userconfig, just use the maste, but with the new update tje only change I made was making msfs active and activating the axis in TelemFFB. prehaps some setting in my vpforce config? Number481, could you share you VPForce settings to check if fix it?

NNumber481 What conditions did the error occur under? Starup of TelemFFB? Loading the Air...

Snooper•11/3/23, 11:42 PM

its kinda random, but happened on the ground. I took off and noticed I had no controls....

SSnooper its kinda random, but happened on the ground. I took off and noticed I had no c...

Number481OP•11/3/23, 11:43 PM

are you running ec8185c5 or dd8b0022 ?

Snooper•11/3/23, 11:44 PM

Snooper•11/3/23, 11:48 PM

and I left off the trim follows and recent implementation to make sure.

Snooper•11/3/23, 11:48 PM

I think its something from VPForce config

Number481OP•11/3/23, 11:50 PM

unless the motors are going into fault state, I doubt its in vpconf. If its happening mid-flight and things are working fine up until then, it's not your config either.

Next time it happens. Grab the entire log from TelemFFB (log folder) and post it here or DM it to me

Snooper•11/3/23, 11:50 PM

ill do

Snooper•11/3/23, 11:52 PM

but if thats the case, after TelemFFB "crashes" I still have all axis so proprably as you say not VPForce Conf fault(or mine, messing with it), but i'll do, thanks for your time wih it!

Snooper•11/3/23, 11:52 PM

and patience

A. Palmetto•11/6/23, 6:53 AM

Do the wires that come in the motor kits come with connectors on them already? Decent amount of slack?

AA. Palmetto Do the wires that come in the motor kits come with connectors on them already? D...

walmis•11/6/23, 8:55 AM

You might need to splice and extend the wires as needed, so have a soldering iron and some heatshrink ready

A. Palmetto•11/7/23, 12:34 AM

Is motor 1 and 2 specific or roll? and pitch?

A. Palmetto•11/7/23, 6:10 AM

Okay kinda confused, I had buttons working before I wrote the settings to the card. Now none of the buttons work from the joystick…double checked the wiring it’s all okay..not sure if the winwing adapter is good?

A. Palmetto•11/7/23, 7:20 AM

So I’ve tried re-wiring the pigtail for the sick just to make sure no breaks in solder. Changed the extension cord for the 5pin. Ran straight adapter to the base 5pin din. Swapped to my other winwing grip. Nada. No buttons register

AA. Palmetto So I’ve tried re-wiring the pigtail for the sick just to make sure no breaks in ...

walmis•11/7/23, 7:23 AM

Can you check the debug output when generic grip (debug) is selected

Wwalmis Can you check the debug output when generic grip (debug) is selected

A. Palmetto•11/7/23, 7:29 AM

A. Palmetto•11/7/23, 7:29 AM

Lots of FFs

A. Palmetto•11/7/23, 7:44 AM

For S&G I also pinned up a spare connector for 5pin and still nada. All FFs @walmis

walmis•11/7/23, 7:56 AM

The problem is on the 5 pin side

walmis•11/7/23, 7:57 AM

A. Palmetto•11/7/23, 7:57 AM

But does the problem lie in the adapter? The board?

A. Palmetto•11/7/23, 7:57 AM

Plugging this in gives me nothing

A. Palmetto•11/7/23, 7:57 AM

A. Palmetto•11/7/23, 7:58 AM

Pinned off this

A. Palmetto•11/7/23, 8:01 AM

One sec let me repin this off your diagram and see what happens

walmis•11/7/23, 8:04 AM

I doubt it's the adapter, unless it was badly pinned and damaged during powerup

A. Palmetto•11/7/23, 8:07 AM

1st or 2nd

walmis•11/7/23, 8:08 AM

2nd

A. Palmetto•11/7/23, 8:08 AM

I’ll report back

walmis•11/7/23, 8:09 AM

oh wait

A. Palmetto•11/7/23, 8:09 AM

Waiting lol

walmis•11/7/23, 8:10 AM

yep 2nd

A. Palmetto•11/7/23, 8:12 AM

That’s how I already had it wired.

walmis•11/7/23, 8:16 AM

try probing the adapter pins, disconnect the adapter cable - put a multimeter in diode test mode, put red probe on GND, and check all other pins with the black probe, it should read a diode (~0.6V) on all the pins

A. Palmetto•11/7/23, 8:18 AM

I’ll have to do that at work tomorrow. I don’t have a meter at home.

A. Palmetto•11/7/23, 8:18 AM

But the freshly pinned one again going off the confirmed pin. Doesn’t work.

walmis•11/7/23, 8:18 AM

That's strange

A. Palmetto•11/7/23, 8:19 AM

Yep still all FF in debug mode

walmis•11/7/23, 8:19 AM

You don't have a TM/Virpil grip to try?

A. Palmetto•11/7/23, 8:19 AM

Negative

A. Palmetto•11/7/23, 8:21 AM

Just two winwing ones. One was brand new that I was using for this. It worked in the initial config thru chrome then when I loaded the VP software they were registering. I did the auto config ran the axis x and y. Saved and stored. And then nothing worked button wise

A. Palmetto•11/7/23, 8:21 AM

Doesn’t matter what mode I put the software in for the button either. Nada

walmis•11/7/23, 8:22 AM

Yeah, would be best to probe the adapter for opens/shorts

A. Palmetto•11/7/23, 8:29 AM

Okay I’ll do that in about 7 hours if you’re still around not entirely sure of the time difference

seems to work fine for me.. best advice I can give s to startup without your userconfig (aircraft w

Similar Threads