Try unpowering it, and check with the diode test mode with reverse polarity applied (red on GND)
Try unpowering it, and check with the diode test mode with reverse polarity applied (red on GND)
WI get ~570mV on all three data pins
Athen I don't get any continuity
WYou should def get a reading. Try black on VCC and red on GND
AI get 2.7 on CK, 2,3 on CS, 0.01 on DI
A(V)
Ayes this has continuity
WYeah, not sure if the pin is fried or there's a short on the board somewhere
Aany idea how I could test and/or resolve this? 
WCan you grab a good hi-res picture of the board?
WIf nothing obvious probably good idea to exchange the board for a new one
ASure:
WCan you also grab the bottom side?
A
Woh there we go
W
Wthat should fix it
Aoeh good catch, lemme clean that out
Aladies and gentlemen, we got it!
Ayou're a legend @walmis thanks for the help
SHey all, just want to get a rough ETA on when to expect the unit to ship after payment. Hope everyone is having a great holiday.
WIt usually ships within 3-5 days
RHowday! Was messing around with Rhino while I wait on replacement winwing adapter and the two times I had a chance to try it after about 10 minutes of playing DCS the Rhino disconnects then reconnects again (reported by windows usb device pop up). It stops responding to DCS ffb until I restart the game.
I’m running rhino through a usb hub, and I’m flying the f14 with telemFFB as well… any ideas for me to fix this tomorrow?
I’m running rhino through a usb hub, and I’m flying the f14 with telemFFB as well… any ideas for me to fix this tomorrow?
ADo you have a log? It would help if it’s getting to hot, motor current, magnetic encoder faults ect.
PIf I understood correctly, you are a developer of TelemFFB. Is it possible to implement a force trim function for FFB pedals via TelemFFB, since DCS only controls one FFB device? Similar to MSFS, where you can also activate the Force Trim function externally via TelemFFB.
RCheers. Will have a look see and post what I can find
WFirst thing I'd try is a direct connection to the PC without the hub
AThe dynamic spring function for MSFS, does not seem to work for Rudder pedals. Flying from stall speed to Vne, i get the same spring tension. Spring gain is set to 100% in the configurator and the potmeters are disabled.
RIf I want to log while I'm testing this, do I just do "log data" from the debug tab?
Rdo I need to leave it enabled or can I export after the fact?
LSo, I’m having a similar issue: turn everything on, go into DCS, joystick centers. If I alt tab and somehow open the teleffb windows, the stick goes limp. There’s still effects going on (like when rolling on tarmac), but no more centering. And I haven’t been able to get it going in game when it happens, like a reset. Rather, a full pc restart is required :/
AEither or should work
ABut definitely try a direct connection first to the pc usb as walmis said
NYou sure its DCS your talking about? 
The behavior you describe sounds a lot like the way IL2 can behave sometimes... I've never had DCS reset its FFB state when the window focus changes.
Does the same behavior occur whether or not you have TelemFFB running?
The behavior you describe sounds a lot like the way IL2 can behave sometimes... I've never had DCS reset its FFB state when the window focus changes.Does the same behavior occur whether or not you have TelemFFB running?
LI'll now try without Telem running and see what happens
JThis also happens to me, occasionally. I can’t seem to reliably replicate it. Rather random.
LI tried it without Telem, switched windows and the same thing happened. Only way I could make it work is by having everything set up such that I didn’t have to switch windows anymore.
AI’ve also had that happen maybe 1x or 2x but it was under heavy motor effect and I got an encoder error. Realized the telemffb settings are based of 50% periodic gain adjusted and hasn’t happened since
ANever tabbing windows tho
DOops, I accidentally cracked the joystick thread connection. when MSFS 2020 starts the rhino in game, The stick immediately dives the y axis into the end stop and with the 10 cm extension (aluminum) attached to a virpil warbird. Wow, the rhino is powerful! How do I order a replacement part and when is the proper time to turn the power on the rhino? I just super glued it back on, gonna wait until tomorrow to rethread the stick.
SIn DCS I feel like the force is to weak around the center when flying the AH-64. I.e. when I force trim the stick there is basically no force on the stick around the first few degrees of movement. Is there some way to add a “baseline” friction so that there will be more force around the center of movement? Using telemFFB. From what I understood there is now way of changing the FFB of DCS itself as it’s run by the DCS module, but maybe there is a way to ad an effect “on top” of the DCS FFB?
OI've had my Rhino for a few weeks now and really enjoying it in DCS but I'm a little concerned about the fan noise when it kicks in. I've made a video - is this the normal amount of fan noise or is there a problem with mine?
ASounds like a fan blade is hitting something. The grille perhaps?
WYeah, sounds like it's touching the grill a bit. Grab a + screwdriver and try to tweak the tension on those fan/grill screws
HHi, which side is front and back? The red knob should it be near us? Or the opposite? Thanks.
TThe red knob should be near. Though you can change it in software if it makes mounting easier
DEither way, you can invert
HDoes not change anything for me. Just that I mounted that in my cockpit the wrong way so had to mount it the other way. 
HThe configurator is just that, a configurator? The device does not need any driver?
Is the 1.0.16 firmware the latest available? As the "update" is not active.
Also, I have a virpil grip, the constellation delta prime. I should use the virpil T50CM2 profile? Thanks
Is the 1.0.16 firmware the latest available? As the "update" is not active.
Also, I have a virpil grip, the constellation delta prime. I should use the virpil T50CM2 profile? Thanks
OThanks. Loosening the screws a little seems to have fixed it. The fan grill does shift ever so slightly now - do I need to concerned about dust ingress? If so I could put a little tape around the edges.
3To get the red button to face away from you,
do you just click on both the Xand Y axis invert in the configurator?
do you just click on both the Xand Y axis invert in the configurator?