Hi, Help needed. My Rhino is not connecting with my MSFS. See image.

BB9 Hi, Help needed. My Rhino is not connecting with my MSFS. See image.

Number481•1/24/24, 7:09 PM

your rhino is connected fine (as indicated by the firmware version in the lower right). MSFS is connected fine (as indicated by the telemetry).. there is an error condition (red x).. suggest you look at the log per the hover-over tooltip and the documentation

But... the reason it's not working is %99.999 because you are in the H160 and have not configured your force trim button in settings

Number481•1/24/24, 7:11 PM

your log will most likely be spamming:

Force trim enabled but buttons not configured

Force trim enabled but buttons not configured

B9OP•1/24/24, 7:17 PM

Please bare with me as I am not very good setting up & configuring software. See Settings image

B9OP•1/24/24, 7:19 PM

My Rhino is not respoding inside the H160 Cockpit

Number481•1/24/24, 7:25 PM

B9OP•1/24/24, 7:30 PM

See image of my VPforce FFB Configurator

BB9 See image of my VPforce FFB Configurator

Number481•1/24/24, 7:33 PM

follow the green boxes in the screenshot I just posted above in your TelemFFB settings. Configure the button you want to use for force trim and it will start working. The entirety of the ACFS autopilot implementation in TelemFFB for the HPG helicopters is dependant on force trim and axis sending being enabled in TelemFFB.

Since it sounds like this is new to you, also be aware that you will need to unbind your joystick axes in MSFS, otherwise it will fight with the axis information being sent by TelemFFB.

B9OP•1/24/24, 7:40 PM

Rhino is not Bound in MSFS Controls. My Rhino Joystick does not respond while in the H160 Cockpit. While in the H160 Cockpit there is no movement of the Joystick. This means H160 cannot fly.

B9OP•1/24/24, 7:43 PM

My Rhino Joystick does move while using the VPforce FFB Configurator Tool

BB9 Rhino is not Bound in MSFS Controls. My Rhino Joystick does not respond while in...

Number481•1/24/24, 7:44 PM

I dont understand. Did you configure a button to use as force trim in TelemFFB as I said ?

B9OP•1/24/24, 7:45 PM

Yes I did do as you decribed

Number481•1/24/24, 7:46 PM

do you still see the red x in TelemFFB for MSFS?

BB9 See image of my VPforce FFB Configurator

Number481•1/24/24, 7:48 PM

your adjustment knob is connected to spring force and is turned to 0.... TelemFFB needs spring force enabled to be able to center the controls

Number481•1/24/24, 7:48 PM

and simulate force trim

Number481•1/24/24, 7:49 PM

it won't start sending axis data to MSFS until the controls are centered so it knows where they are

B9OP•1/24/24, 7:49 PM

The Red x has cleared and it is blue, see image

B9OP•1/24/24, 7:49 PM

Maybe I have to restart my PC?

Number481•1/24/24, 7:50 PM

B9OP•1/24/24, 7:53 PM

It is Obvious I have no idea how to setup the Rhino Software. Has any one made a video showing and describing how to setup the Rhino Software?

BB9 It is Obvious I have no idea how to setup the Rhino Software. Has any one made a...

Number481•1/24/24, 7:55 PM

Its not hard once you understand what a few basic things do and how they work together... Without TelemFFB running, is there any spring force on your Rhino or is the stick limp?

I have to step away for work stuff for a while but will be back later

B9OP•1/24/24, 7:56 PM

ok. The stick is limp and the black dial is a Zero

Sunshine•1/24/24, 8:00 PM

So my DIY kit came, these servos are HUGE!

Sunshine•1/24/24, 8:00 PM

B9OP•1/24/24, 8:01 PM

When I restarted my MSFS simulator the red x came back

BB9 When I restarted my MSFS simulator the red x came back

TrigaNZ•1/24/24, 8:16 PM

Set your POT1 to Master Gain and turn it up. Do a calibration. Apply and Store. Close configurator. Open FFB. Open MSFS.

B9OP•1/25/24, 2:44 AM

Thank you very much for your incredibly amazing support with my Rhino Software Setup. My Rhino is working Perfectly. Thank you.

Caprice•1/26/24, 10:07 AM

Hello, absolutely loving the Rhino, its a true gamechanger for me. I was noticing a problem with my endstops, when i put even a little force on them, they "break" and the stick goes past the point, and the axis goes limp.

Caprice•1/26/24, 10:07 AM

This is not very much force at all.

CCaprice Hello, absolutely loving the Rhino, its a true gamechanger for me. I was noticin...

walmis•1/26/24, 10:13 AM

That could be the motor stability safety protection, try reducing Spring and Damper LPF values in Expert settings

walmis•1/26/24, 10:13 AM

Try something like

Wwalmis That could be the motor stability safety protection, try reducing Spring and Dam...

Caprice•1/26/24, 10:35 AM

Thank you will try. Amazing work on this!

Gadroc•1/26/24, 7:05 PM

Has anyone got the VKB adapter to work? The screw used as the anti-rotation post is larger than the holes on the VKB grips (3mm instead of 2.5mm of the post on the real base.)

GGadroc Has anyone got the VKB adapter to work? The screw used as the anti-rotation pos...

Fierce_Fire•1/26/24, 7:14 PM

What part do you mean? I just used whatever came with the grip and it mounted in one go

Gadroc•1/26/24, 7:16 PM

The little silver nub… it slips into one of two holes on the grip for either straight or 15angle. That pin is 2.5mm round. The vkb adapter has an m3 screw in the same location that does not fit into the grip. Prevents the grip from seating all the way.