This sound is when motors are not receiving power
This sound is when motors are not receiving power
WTry opening the VP configurator app and see what's the status
PI double checked, but the ac adaptor is plugged in as well as I can make it. The application itself shows the USB to be disconnected, with both motors offline
PI was starting to get an issue yesterday where the stick was randomly connecting/disconnecting
P
WHmm, try maybe another cable
PI don't have another usb cable of this sort to my knowledge?
WYesterday was a similar issue, starting to wonder if there's a bad batch of USB cables
PWyeah, it's a common printer cable
WAlso some other things to try: reboot, plug into the back connector of the PC
POK I'll order a new one. Just a bit annoyed this occurred a week into getting the base. Yeah I've already tried that method I'm afraid
SAre there any plans to update the VKB adaptor for rev C grips. I’m not even sure you can buy grips with rev B connectors anymore.
Bil2
GJust want to verify: The VKB adaptor fits the MKIII grips and not the MKIV?
WYeah
GThanks!
Bi am really struggling to get the DIY build working, from a software standpoint , i posted about IL2 but disregard that as it may be an excess controller issue that i need to delve into further. I thought i would try DCS , so i v red then reread the manual , i m just looking for simple FFB and axis assigment to prove my stick works . Whree i ve got to
1 In VPC i ve set up a spring , tried end stops and damper, i m getting readouts on all parameters from the right hand side display, X through to Vbus all show dynaimc returns based on stick movement . Bottom right shows Motro X and Y and USB as OK asnd connected . Device Firmware reads 1.0.16 and debug shows i can save and write serttings to memory . The stick feels limp , no real force needed to move it , which is sort of confimed on the X and Y currents which as pulling <0.5 amp . I assume all this is normal
2 Telem FFB (now using latrest WIP version) , ive selected DCS in the Sim setting section , and i get a yellow pause "Sim enabled waiting for data , i launch DCS from Steam , selected multithread, go to settings FFB is enabled , but yellow box does not change
From log file
hid.HIDException:
ReadFile: (0x0000048F) The device is not connected.
2024-03-18 15:49:19.669 - ERROR - joystick - Exception
Traceback (most recent call last):
File "ffb_rhino.py", line 513, in timerEvent
File "ffb_rhino.py", line 582, in readReports
File "hid.py", line 163, in read
File "hid.py", line 148, in __hidcall
hid.HIDException: ReadFile: (0x0000048F) The device is not connected.
1 In VPC i ve set up a spring , tried end stops and damper, i m getting readouts on all parameters from the right hand side display, X through to Vbus all show dynaimc returns based on stick movement . Bottom right shows Motro X and Y and USB as OK asnd connected . Device Firmware reads 1.0.16 and debug shows i can save and write serttings to memory . The stick feels limp , no real force needed to move it , which is sort of confimed on the X and Y currents which as pulling <0.5 amp . I assume all this is normal
2 Telem FFB (now using latrest WIP version) , ive selected DCS in the Sim setting section , and i get a yellow pause "Sim enabled waiting for data , i launch DCS from Steam , selected multithread, go to settings FFB is enabled , but yellow box does not change
From log file
hid.HIDException:
ReadFile: (0x0000048F) The device is not connected.
2024-03-18 15:49:19.669 - ERROR - joystick - Exception
Traceback (most recent call last):
File "ffb_rhino.py", line 513, in timerEvent
File "ffb_rhino.py", line 582, in readReports
File "hid.py", line 163, in read
File "hid.py", line 148, in __hidcall
hid.HIDException: ReadFile: (0x0000048F) The device is not connected.
NWith no sim running, do you get the expected results from your joystick? Spring/damper/ whatever you have set up in configurator?
Bno i did breifly but in VPC i get "no feeling"
NWhat is your device PID set to in configurator ?
NPost screenshots of your configurator settings and effects pages.
BUSB PID = 2055
B
B
Nignoring the telemffb issue for the time being... You don't have a pot connected to port 1, so I would set the Port-1 seting to disabled. Your pot on port2 is turned down pretty far, and is connected to damper, so that will be extra weak.
Your periodic effects LPF is set to %0..., so once we do get TelemFFB working, none of the rumble effects will do anything. I suggest loading the Rino default profile thats in the configs directory of your configurator install, redo your calibration and start from there.
Your periodic effects LPF is set to %0..., so once we do get TelemFFB working, none of the rumble effects will do anything. I suggest loading the Rino default profile thats in the configs directory of your configurator install, redo your calibration and start from there.
Nalso be aware that when you launch DCS, it will send a reset to all FFB devices, so until you load into an aircraft, everything will go limp.
Bok , thanks will try that and repost , i ve disabled both Pots , interesting as soon as i touch pot 1 knob iit showed a return and scales perfectly to 100% whilst give an audible beep , anyway disabled both for now
Nonce you get it working as expected without any sims or telemffb running, we can look at the other issue
Bok so Default Config loaded , Effects tab not touched , just showing springs at 100%, and Calibration rerun
NDoes spring/damper work as expected? (make sure they are also enabled in the effects tab still)
Bno i get no feel on the stick , if i turn off via red stop it does not really make any difference to feel
Nhard to know how consistent the info is between the two screenshots you just posted.. but given the slider/effect settings you should, at the very least, have spring force. However, in the first screenshot, you still have pot 1 connected to spring gain... in the 2nd screenshot it shows pot 1 at 0%
Bi think i must have touched something let me recheck
Bok , so both POTS diaabled i do get a SPRING force , and can see it in the blue dot represntation with a force pulling back
Ngood... enable damper in the effects tab and you will get damper force too
Broger , that works as expected
Nok.. before you jump into a sim and try getting TelemFFB running... try this little test app I built. Hit the connect button, and enable the periodic or constant (or both) checkboxes and hit start.. you can change the direction/intensity, etc... and hit start again to add new effects on top of the running ones, or hit stop and then start new ones...
Rhino_Tester.exe24.9MB
Bit connects , when i select start i get no response on stick , then after about 3 seconds the command window flashes up breifly with info and then closes , tried 3x now , also with Avast closed for now
Nyou have to enable one or more of the effect checkboxes
Bit crashed a few times , but now i ve got a periodic shake , like a slow motion gunfire
Nthe app is half baked so crashing doesn't surprise me.. but it connects, which is what I really wanted to see (since that was the error you posted in the telemFFB log). It connects using the exact same code as this app.
Close the test app and launch TelemFFB (Still with no sims running).. make sure you see it connect in the log..
Close the test app and launch TelemFFB (Still with no sims running).. make sure you see it connect in the log..
Bto me this log looks better 2024-03-18 17:07:25.538 - INFO - joystick - Open Rhino HID FFFF:2055
2024-03-18 17:07:25.569 - INFO - joystick - Successfully opened HID '\?\HID#VID_FFFF&PID_2055&MI_00#c&34f068b0&0&0000#{4d1e55b2-f16f-11cf-88cb-001111000030}'
2024-03-18 17:07:25.624 - INFO - joystick - Rhino Firmware: v1.0.16
2024-03-18 17:07:25.625 - INFO - joystick - Logging level set to:INFO
2024-03-18 17:07:25.700 - INFO - joystick - Telemetry timeout: 0.2
2024-03-18 17:07:25.701 - INFO - joystick - Found Saved Games directory: C:\Users\jthic\Saved Games
2024-03-18 17:07:25.701 - INFO - joystick - Checking C:\Users\jthic\Saved Games\DCS\Scripts
2024-03-18 17:07:25.702 - INFO - joystick - Checking C:\Users\jthic\Saved Games\DCS.openbeta\Scripts
2024-03-18 17:07:25.702 - INFO - joystick - Starting DCS Telemetry Listener
2024-03-18 17:07:25.718 - INFO - joystick - Listening on UDP :34380
2024-03-18 17:07:25.718 - INFO - joystick - Starting IL2 Telemetry Listener
2024-03-18 17:07:25.718 - INFO - joystick - Listening on UDP :34385
2024-03-18 17:07:25.569 - INFO - joystick - Successfully opened HID '\?\HID#VID_FFFF&PID_2055&MI_00#c&34f068b0&0&0000#{4d1e55b2-f16f-11cf-88cb-001111000030}'
2024-03-18 17:07:25.624 - INFO - joystick - Rhino Firmware: v1.0.16
2024-03-18 17:07:25.625 - INFO - joystick - Logging level set to:INFO
2024-03-18 17:07:25.700 - INFO - joystick - Telemetry timeout: 0.2
2024-03-18 17:07:25.701 - INFO - joystick - Found Saved Games directory: C:\Users\jthic\Saved Games
2024-03-18 17:07:25.701 - INFO - joystick - Checking C:\Users\jthic\Saved Games\DCS\Scripts
2024-03-18 17:07:25.702 - INFO - joystick - Checking C:\Users\jthic\Saved Games\DCS.openbeta\Scripts
2024-03-18 17:07:25.702 - INFO - joystick - Starting DCS Telemetry Listener
2024-03-18 17:07:25.718 - INFO - joystick - Listening on UDP :34380
2024-03-18 17:07:25.718 - INFO - joystick - Starting IL2 Telemetry Listener
2024-03-18 17:07:25.718 - INFO - joystick - Listening on UDP :34385
Nyep.. now start DCS
B2024-03-18 17:12:08.947 - INFO - joystick - Device reset event: Invalidating all effects added as i launch DCS
BDCS running, FFB in MISC checked , yellow icon in Teleb FFB for DCS
SI see from a previous message that you were struggling to get your hands on a Rev.C extension in order to make an adapter for MkIV gunfighter grips. Any progress on this? I have 100mm and 200mm Rev C extensions that I’d be willing to provide for research as I’m getting close to the end of the queue and it would be something I’d like by the time I get there 
Nthis is normal.. thats DCS taking control of the ffb device. DCS doesn't send any telemetry until you load into a flight, so it will remain yellow until you do so.. after which it will appear paused when paused or not in an aircraft.
Bthanks , i launched an F86 , had a quick fly , did something that got a violent stick shake but other than that i felt gentle feed back , going to fix to mount and then try subtle changes , etc from then , just out of info , what was the main cause of issue at start , shall i just keep pots disabled , or possibly physically disconnected from board ?
NCouldn't say for sure why telemffb failed to connect before.. could be any number of things.... hung instance.. maybe you had 2 instances up and didn't realize it... maybe your e-stop switch was off, etc, etc.
The pots are fine to have connected, as long as you understand how they work and what they do and how far you want to turn them up... they really just offer a convenient quick way to adjust one setting or another.
The pots are fine to have connected, as long as you understand how they work and what they do and how far you want to turn them up... they really just offer a convenient quick way to adjust one setting or another.
BOk thanks a lot for the detailed support ,