KYes, rest is fine. I've played with grip selection settings but no joy.
WNo clue, sounds like it could be a wiring issue/fault in the grip itself for that particular input.
It should just work.
It should just work.
KI know this from TM manual but I'm not sure if it's the same case with Rhino
WAh
Wcould enable the "debug" grip and check if any data changes in the Debug tab window when you depress that button?
KWill do
KNothing
MOK, figured itt out....
MI had to unclip the connector to lift the plate out enough to rotate it.....
WYou need to push the cable into the tube
MJust worked that out, cheers walmis...
KCopy, thanks for help. I will try to replace it.
DAny tips for my question for ac adapter disconnecting easily. Am I the only one with this issue as there is no one saying anything. Usb adapter is not loose but ac adapter is kinda loose I tied wire down below around my mount so usually it is nit dissconnected but it happened now in last few weeks 2-3 times that during usage wire dissconnects from vibrations I guess. Very frustrating spec when I was playing in VR and just all of a sudden stick goes limp.
WCan you make a short vid demonstrating how loose it is?
MIs there a way to offset the grip slightly ( twist it slightly to the left to allow for me mounting it centrally and using my right hand ) In my other simpit, I was using an extension and could turn it using that. In this pit, I am not using an extension. I cant angle the base either due to using the mounting plate which sits at a right angle on a cross member.
Fdepends on the grip I guess.
you can fasten the Virpil Constellation Alpha however you want to
you can fasten the Virpil Constellation Alpha however you want to
DDHere is is
Fisnt that not in all the way?
Fmy cable isn't that much different. my plug goes in 3/4 of they way but it does not wiggle that much.
I did not force wiggle it like you did though.
I did not force wiggle it like you did though.
Dit is all the way in
Fexactly
Fyour connector looks to be worn out a bit though.
did you pull the cord or something?
did you pull the cord or something?
Dthere is around 3 mm more but I cant put it in more and it just slides out easily and wiggles like that from day 1, thought that is weird from the start but started bothering me now once it dissconect during play even tough I secured the wire so it dosen't get pulled
Dif it looks worn its only looks like that in vid it is pristine
Dwhere does connector looks worn?
DAs I said it is same feeling of connection from day 1
Dit is not all the way in, wiggles and slides out easily
Fthe socket has some metal springs keeping the plug tight. mine does not wiggle that much.
but you are as deep in as possible.
the plug is just longer than the socket is.
but you are as deep in as possible.
the plug is just longer than the socket is.
Nlooks like these little spring tabs need to be bent back out a little to create some tension on the outer plug barrel
DSo Should I try and bend them a bit?
Nits what I would try... but I've also never been a very good role model so....
DOk helped a bit I think still loose but less slidy feel I think It will be fine will see after some testing.
VHi @walmis , I have received a DIY kit and trying to connect everything together. WebUSB connects well and I can move a point (one axis is reversed) but Configurator app says USB: Disconnected and both motors offline. Tried a different cable - no luck. Joystick is detected by Windows once I plug the USB in.
Sdid you hook up 20V power?
WSounds like windows serial driver is not functioning. Which Windows version are you using?
VI use Win10, 20V Power is connected
Weird, but I can even bind controls in Condor2 sim to Rhino
Weird, but I can even bind controls in Condor2 sim to Rhino
VAfter creating and executing .bat file for launching with
-serial
OI just turned the plug around on the stick not the Rhino base , but that was with thrustmaster, yours maybe different situation.
YThis method is really good and solved my problem. Now the software is working fine
Bhey everyone I came across an issue today in DCS Apache (could relate to other modules) with the force trim... what I noticed is if I set an axis tune S curve on the cyclic it messes with the FFB effects when you trim release (set a new trim position). The joystick and ffb want to return your stick to the centre by a small amount, the physical centre not the trimmed position. When I remove the curves within DCS to linear the Rhino and ffb behaves as I would expect with the spring accepting the new centre.... Is this normal or am I doing something wrong?
Nit is normal. Axis curves are not compatible with FFB
Bty @Number481 that is very useful information
Pnot too sure if this is the correct channel ...but...
PDEfender just spazzed out and nuked telemffb
P
Panother in a long line of defender sapazzes I guess from praydog UEVR and github trojans its all been a bit of a mess recently ( praydog takes pancake games to VR in openXR) really cool...but I digress... anyone else have this happen ? I've put and exclusion now into defender for the telem location.
NLooks like a windows secure update today is now flagging the latest build. Was fine this morning. 
Adding an exception for your TelemFFB folder as you did, while less than ideal, is the only real solution….
Adding an exception for your TelemFFB folder as you did, while less than ideal, is the only real solution….
Pcue the influx of why is telem not loading anymore !!