Power plug has started to fall out when I have lots of feedback. And ideas how how to keep it in?
Power plug has started to fall out when I have lots of feedback. And ideas how how to keep it in?
NI'm using a workaroud by defining a deasspace in the Tune Axis section in DCS.
WIn your setup, encoder position wraps around, so it can be undefined at startup.
I suggest you follow the instruction about initial belt position/calibration:
I suggest you follow the instruction about initial belt position/calibration:
TDIY or production unit?
If DIY you can take it apart and add the “Twist lock” connector.
Here is the Male 5.5 x 2.1 (same size as the Rhino plug) with “Twist lock”. Get the female and swap them out.
IF you are using a production unit ask @walmis because opening or swapping parts probably void any warranty?
So the answer is: “It depends”
But yep that’s the part you need and that’s why they lock in place
Hope that helps
If DIY you can take it apart and add the “Twist lock” connector.
Here is the Male 5.5 x 2.1 (same size as the Rhino plug) with “Twist lock”. Get the female and swap them out.
IF you are using a production unit ask @walmis because opening or swapping parts probably void any warranty?
So the answer is: “It depends”
But yep that’s the part you need and that’s why they lock in place
Hope that helps
T(You need the Male and Female btw but I assume you know I just wanted to clarify)
CThank you for the feedback. It is a production unit, so definitely would not want to void any warranty.
BGaffer's tape over the plug? Might be easier if you got a 90° extension. https://www.amazon.com/dp/B09SZ8HV2P?psc=1&ref=ppx_yo2ov_dt_b_product_details
L-Shape 5.5mm x 2.5mm DC power supply extension cable, convert straight plug to 90 degree right angle plug, male to female plug jack connector extension cord. The 90 degree right angle plug jack cable can be easily go through the narrow gap, will never bend and damage the power supply cord. This ...
CI will see what I can do
BHello, how do I get force feedback to work in War Thunder. When I enable force feedback in game the stick goes limp as it should on ground but never stiffens up while flying. Any ideas?
NGreat! Thank you, will try this
Hinstalled the UH-6A and perhaps did something wrong in the clone dialog in Telem ffb. It seems that it doesnt recognize it, because curret aircraft is unknown.
Hjoystick log:
message.txt7.17KB
Hpedals log:
message.txt6.69KB
Hdoes someone no how to get to normal? If I restart dcs and load the p51 all is fine
Nuntil the next TelemFFB release, you'll need to replace the export script in the TelemFFB export folder with this one: https://discord.com/channels/965234441511383080/1230852705593851964/1235261252306206740
HThank you very much @Number481 i will try that. 
AAnyone have a winwing adapter fail on them? I checked the stick on the OG base and all the buttons work there. It used to work but I took the stick off and now I'm trying to put it back on and it won't pick up the stick. Wiggling the connection around I did see 2 buttons illuminate on the software for a moment but can't get it all now. I tried forcing the connection down pretty hard like another user did to get it working but it's not happening for me.
VIs there any way to make the hat switches work as hats on my VPC T-50CM (not CM2) ? If I select the CM2 grip almost everything works, but the hats are only recognized as buttons
KYes, mine died on me also. Search for my messages and contact Walmis for replacement
TThis question confuses me?
A 4 way hat switch is technically 4 buttons mapped Up, Left, Down, Right.
So far as I’m aware the original CM does not have push click hats (5 way).
So the hat switch should be picked up as 4 separate switch inputs.
Is it not working that way? Or what’s the behavior of the switches?
Sorry I can’t be more help but I’m setting up a T50CM next week so I’m watching to pick up tips and tricks along the way.
A 4 way hat switch is technically 4 buttons mapped Up, Left, Down, Right.
So far as I’m aware the original CM does not have push click hats (5 way).
So the hat switch should be picked up as 4 separate switch inputs.
Is it not working that way? Or what’s the behavior of the switches?
Sorry I can’t be more help but I’m setting up a T50CM next week so I’m watching to pick up tips and tricks along the way.
TThis is just a question for my own knowledge but why do they need to be hats? Why can’t you use them as buttons?
TBasically what touch of legend above me said lol
VYou are correct. Its a minor thing, but if windows recognizes as a hat and not 4 buttons, it makes live a little easier, for instance in jo2key I can see a hat switch and direction which is easier to remember than button 23, or condor asks for a POV hat switch and I supposedly dont have any. Not a big deal, I can map them as 4 separate controls, just wondered if I could tweak that somewhere
TAhh cool maybe it can be suggested for an update?
Speaking of Telem updates I think there was one today!
Speaking of Telem updates I think there was one today!
Ndid you try disabling these checkboxes?
Vyes
TDoes the winwing adapter have anything other than a 6pin to 5pin connector inside it?
TI have the same problem with my winging adapter. @walmis response was to press it in really hard, but its a problem with how the the connector he uses in the adapter and the connector on the stick connect. Not sure if it's a depth problem or what. I can wiggle the connection and see my stick connect/disconnect fine but as soon as you tighten it, it's kind of hit/miss. If you get lucky and it's all tight, it works great, if it happens to spin (since there's no way to lock the spinning on the stick) then you lose the connection. If I connect a separate wire between the WW grip and the adapter, it is just fine. Im currently working on how to hack/fix it but have not been successful yet.
A@Kowalsky I don't believe so. Appears to just be 5 to 6 pin. It did connect for a brief moment when I was wiggling it but I can't get it to happen again. I also think it's a depth issue. Almost wondering if I can put something conductive inside the female side to make the connection but I'm afraid I'll damage the mail end. I did speaking with Walmis this morning and it sounds like I'll be getting a replacement. Walmis is the freaking man!
TStill having the same problems. I've discovered that you if you wiggle the wire it connects/disconnects, it's not a solid connection, force doesnt fix it. It's hit or miss if I get it connected and tightened at the same time. As I fly, sometimes the stick rotates a bit (winwing problem) and that disturbs the wire enough to disconnect the stick. I have a 3ft PS/2 extention wire that I can plug from the stick directly to the base and no disconnect problem when wiggled.
MFrom what i remember the CM Grip is wired differently than cm2 so the hat is not where the software expects. It should work with Thrustmaster mapping, that's what the original cm grip is using.
TAwesome I’m also going to try this!
Thanks to the both of you for figuring out an issue before I even had it lol
Thanks to the both of you for figuring out an issue before I even had it lol
TBecause yeah the CM has a normal single button on the “thumb press” instead of the Slew/sensor Hat the CM2’s have.
HI did the update, and now it seems to work, I just wonder that my poti has no influence now. Before i just reduced spring by the poty and could fly heli. do i have to repeat some settings to get this working again. Please no rush with answering, enjoy your weekend and kind regards...
DSo I just fired up my PC and have an odd issue - my Rhino appears to work and is "seen" by TelemFFB and WebUSB tool, but not within VPForce Configurator. Thoughts?
D
DThat is all I get.
DStill works fine in game. I've moved it from different USB ports and get the same thing.
BJust a random thought.
Anything like HidHide running and you forgot the let the stick visible to the configurator ?
Anything like HidHide running and you forgot the let the stick visible to the configurator ?
DFalse alarm. I am running HidHide, but that wasn't it. On a hunch I powered down the PC completely and unplugged my USB cables and hubs and left them off for a minute, then powered it all back up. I noticed I was having odd issues with my HS70 wireless headset as well and figured that might be it....and it was.
DI need to engage brain before panic and asking questions. 
BHardly hurts, and sometimes not asking can be much more expensive
DTrue! 
Thanks for the suggestion!
Thanks for the suggestion!BJust only thing I could think of where it would work in some applications and not another, banged my head against that one myself once or twice
Band thats one more for the block list
Awow looks like a pretty sweet deal
NDoes it have FFB?
Nnew issue with any ammount of periodic effects my stick will be constantly wiggling even not in game
LHow to set up the Damper force in Heli trim mode? I wanted to have some strong damper force when holding the trim button in Apache. Now the problem is when holding the trim button, there is no force to hold the stick.