RAT OS 2.1 RC1 Homing Issue

Fresh Install of Rat Os 2.0 , verify motor directions and endstops. Home X and Y and the printer PUSHES the Z up into the nozzle when homing Y and X (Which is the opposite function of RATOS2.0 to reduce hitting extruder before homing Z) . Then it says 'no beacon model found' when trying to home Z. So to use the Z i need to calibrate_beacon, but when I calibrate Z it says out of range when trying to save the beacon profile.

What I did , fresh install 2.0 , verify everything motion, then i updated using the update manager, then tried to home. So maybe the update broke something. Picture for the LOL.

blacksmithforlife•5/31/24, 11:15 PM

The bed shouldn't go up when homing so it sounds like the Z needs to be reversed.

Bblacksmithforlife The bed shouldn't go up when homing so it sounds like the Z needs to be reversed...

dropsOP•5/31/24, 11:38 PM

I thought so too! However if i set it to kinematic, and go Z down , it goes down!

dropsOP•5/31/24, 11:38 PM

Also goes up if it goes up

Ddrops I thought so too! However if i set it to kinematic, and go Z down , it goes down...

miklschmidt•5/31/24, 11:38 PM

"Z down" is very ambiguous. If you click the "z down" it will decrease Z which means bring the bed closer to the nozzle. That default mainsail behavior. Remember you're in upside down land compared to something like a bed slinger.

Mmiklschmidt "Z down" is very ambiguous. If you click the "z down" it will **decrease Z** wh...

dropsOP•5/31/24, 11:39 PM

DAMMIT, USER ERRROR!

dropsOP•5/31/24, 11:40 PM

Im so emberassed

Ddrops Im so emberassed

blacksmithforlife•5/31/24, 11:40 PM

It happens, I've done it myself

Ddrops Im so emberassed

miklschmidt•5/31/24, 11:41 PM

Don't be, unfortunately it happens.. The mental overhead of the toolhead command panel is heavy.

dropsOP•5/31/24, 11:41 PM

Its been so long since ive had to configure from scratch

miklschmidt•5/31/24, 11:42 PM

The only real way to avoid accidents is to make sure things can't fail before you've had a chance to hit the emergency stop. It's one of the reasons the SET_CENTER_KINEMATIC_POSITION is used by centering all axes.

Mmiklschmidt The only real way to avoid accidents is to make sure things can't fail before yo...

dropsOP•5/31/24, 11:45 PM

Im so emberassed I just sent a one time sponsor...

Ddrops Im so emberassed I just sent a one time sponsor...

miklschmidt•5/31/24, 11:46 PM

Hahaha i appreciate it, but be safe now!

Mmiklschmidt Hahaha i appreciate it, but be safe now! 😅

dropsOP•6/1/24, 12:09 AM

@miklschmidt funny you should say that...literally happened like 5 minutes before you said that.

dropsOP•6/1/24, 12:09 AM

Forgot to set the endstop so rushed to turn the printer off so it wouldnt crash

dropsOP•6/1/24, 12:10 AM

Ddrops @miklschmidt funny you should say that...literally happened like 5 minutes befor...

miklschmidt•6/1/24, 12:12 AM

Ouch

Ddrops Forgot to set the endstop so rushed to turn the printer off so it wouldnt crash

miklschmidt•6/1/24, 12:13 AM

I've done this more times than i'd like to admit. Stupid slippery floors.

Ddrops Forgot to set the endstop so rushed to turn the printer off so it wouldnt crash

miklschmidt•6/1/24, 12:14 AM

there's an emergency button in mainsail, just hit that instead then you don't have to run

Mmiklschmidt there's an emergency button in mainsail, just hit that instead then you don't ha...

dropsOP•6/1/24, 12:14 AM

Will do next time, totally forgot about that!

Mmiklschmidt there's an emergency button in mainsail, just hit that instead then you don't ha...

YouvBeenThumped•6/1/24, 12:17 AM

Until you hit it.... And the printer keeps going cause it hasn't registered the command :FLASHBANG:

YouvBeenThumped•6/1/24, 12:18 AM

Now has fancy cat outline on wham bam sheet

dropsOP•6/1/24, 12:42 AM

Lol

dropsOP•6/1/24, 12:42 AM

Well im leaving the emberassing scratch and video up , and having an update. IT WORKS!

dropsOP•6/1/24, 12:42 AM

Just completed my first full auto_beacon_calibration

YouvBeenThumped•6/1/24, 12:43 AM

Im working up the courage to attempt it currently

YYouvBeenThumped Im working up the courage to attempt it currently

dropsOP•6/1/24, 12:51 AM

My advice, have two SD cards, saved your printer config, remember motor directions, and prepare to troubleshoot the becaon

dropsOP•6/1/24, 12:52 AM

had to do two clean OS installs for it to work

Ddrops My advice, have two SD cards, saved your printer config, remember motor directio...

YouvBeenThumped•6/1/24, 1:20 AM

I don't use SD cards. NVME drive

YYouvBeenThumped I don't use SD cards. NVME drive

dropsOP•6/1/24, 1:22 AM

https://tenor.com/view/bad-ass-uh-oh-ndt-neil-neil-degrass-tyson-gif-14802463180959376587

Tenor

YouvBeenThumped•6/1/24, 1:25 AM

I just hate when sd cards cease to be sd cards

Ddrops Fresh Install of Rat Os 2.0 , verify motor directions and endstops. Home X and Y...

jhorn68 (V-Core 4 400)•6/4/24, 4:00 AM

Don't feel bad, I did it too...

Jjhorn68 (V-Core 4 400)Don't feel bad, I did it too...

dropsOP•6/4/24, 4:22 AM

dropsOP•6/4/24, 4:22 AM

If only they would rotate the damn Z arrows for non bed slingers in mainsail we wouldn't have this issue

dropsOP•6/4/24, 4:23 AM

They don't even have to change any code , just rotate the icons 180°

Ddrops They don't even have to change any code , just rotate the icons 180°

jhorn68 (V-Core 4 400)•6/4/24, 4:39 AM

You can set it in the settings, I had done that and forgot about it. I also had a backup of my printer.cfg and didn't think to look until it was too late.

RAT OS 2.1 RC1 Homing Issue

Similar Threads

Similar Threads

Similar Threads