Where does one get a 1 foot extention 5 pin cable male to female lol
Where does one get a 1 foot extention 5 pin cable male to female lol
WI have this fixed internally for the next version, will roll out with next update 
TNot gonna lie but most of them come with extension purchases.
I’d be interested to see a link as well as for different sizes since here a lot of folks 3d print stuff (including extensions).
So great question!
I’d be interested to see a link as well as for different sizes since here a lot of folks 3d print stuff (including extensions).
So great question!
PHey guys what grip should I select in vpforce config app when using the VKB adapter? is it disable?
Phmmm been haviong this issue more recently- noticed directly with phantom whereby the stick is offset centre forwards...
Pbut now - given that I've reset the config, the circle ( virtual centre is up at the top ????!?!?
Pif I click Sticky for spring then the circle moves back to the centre
Phaving said that either way- the joystick tends to 'vibrate/quiver'
Pany thoughts ?
PIf I run msfs or dcs thibngs seem to stabilise
Pand I'm now exited and closed down telem and joystick returns to normal centered circel
P
WCenter point is controlled by application, so it's best to look at telemFFB here. #
telemffb-user
telemffb-user
KYeah, thrustmaster being different then normal 5 or 6 din, on top of all the cords being 5 feet plus, means I need to learn to solder I guess lol.
AConfigurator update when™? 
DHi all
Seems I'm too stupid to set up my Rhino correct - I've followed the manual, connected the Rhino, did Auto Calibrate and use following settings but there is no FF at all - red knob is released not pressed. What am I doing wrong?
Seems I'm too stupid to set up my Rhino correct - I've followed the manual, connected the Rhino, did Auto Calibrate and use following settings but there is no FF at all - red knob is released not pressed. What am I doing wrong?
TAs a test of the device connection.
Turn/twist the potentiometer completely to the OFF.
With your settings (above) that says the Pot is set to Sping gain.
That should remove all spring tension from the Rhino.
Now move the stick side to side.
Does it stay?
Now turn the potentiometer to full and the Rhino should spring to center.
That shows the Rhino is connected and speaking to the software.
After that you need to start the telem app (update as needed) and start a game!
Turn/twist the potentiometer completely to the OFF.
With your settings (above) that says the Pot is set to Sping gain.
That should remove all spring tension from the Rhino.
Now move the stick side to side.
Does it stay?
Now turn the potentiometer to full and the Rhino should spring to center.
That shows the Rhino is connected and speaking to the software.
After that you need to start the telem app (update as needed) and start a game!
LDid you hear a beeping sound when you connected power and USB ? Is the stick not centering when you turn the knob? What simulator are you testing?
Lalso it may feel be a bit strange with 100% friction (check the slider)
DThank you both! Have to apologize, the issue was sitting right in friont of the display!! When I did the Auto calibration something went wrong, everything (forces, etc.) were set to 0 and all forces were gone. When I reaplied my settings I forgot to send it to the device! Shame on me!
DSo forces are back and I'll retry my config in DCS
WI suggest reducing max Damper and Friction sliders to 30-40% so It won't become unstable if some app tries to create a damper at 100%
PAre there instructions somewhere to swap out the standard grip mount for the aluminum grip mount?
OHi guys, just had my delivery of the rhino, it’s bloody beautiful.
I have absolutely no idea how to really use a pc, I’ve got the rhino plugged in and downloaded whatever it was, I have found the file vp force config, clicked on it.
I’ve got a big red cross plus Qt5Charts.d11 not found.
Wtf is that and how do I proceed?
Guys I’m willing to pay for the time you spend helping me out.
I did have one guy helping but he’s not around anymore.
Thanks for any help in advance.
I have absolutely no idea how to really use a pc, I’ve got the rhino plugged in and downloaded whatever it was, I have found the file vp force config, clicked on it.
I’ve got a big red cross plus Qt5Charts.d11 not found.
Wtf is that and how do I proceed?
Guys I’m willing to pay for the time you spend helping me out.
I did have one guy helping but he’s not around anymore.
Thanks for any help in advance.
Nif you are getting an error like that with the configurator software, you probably copied or moved the exe out if its folder or you are trying to run it from inside the zip file without extracting it first. You must unzip the whole package downloaded from https://vpforcecontrols.com/usb/rhino/ and unzip it to your PC (location is not important). Then run the VPforce_FFB_Configuratyor.exe file that is in the resulting directory.
BI also recommend setting both the configurator and especially your folder for telemffb as folder exclusions in windows defender.
Howto:
https://support.microsoft.com/en-us/windows/add-an-exclusion-to-windows-security-811816c0-4dfd-af4a-47e4-c301afe13b26
Howto:
https://support.microsoft.com/en-us/windows/add-an-exclusion-to-windows-security-811816c0-4dfd-af4a-47e4-c301afe13b26
Find out how to stop Windows Security from alerting you about or blocking a trusted file, file type, or process, by adding it to the exclusions list.
BOr defender loves to go in panic mode over telemffb and delete the executable when you try to launch it.
IWhen I have my Rhino plugged into the same USB hub as my X56 throttle, I get phantom button presses on the lower 3 momentary switches on the throttle. I resolved this by plugging the Rhino directly into the computer instead of the hub, but I thought I'd put it out there for anyone else possibly experiencing something similar.
II was flying along and my gear would just randomly start coming out and sometimes the drag parachute in the phantom would deploy since those are all bound to those 3 switches 
Fis that a powered hub or an unpowered one?
IIt's either. When I'm playing DCS, it's unpowered since I use that plug for the Rhino's PSU. Could be why.
FI am pretty sure that the x56 is allergic to unpowered hubs. might be the case in general for controllers. don't know
IIt seems to work totally fine when just my pedals/throttle are plugged in. The moment I add the Rhino is when things start to become weird.
IMaybe those 2 devices are the limit.
OAnyone in wales on here willing to sort out my sim.
I don’t know anything about setting up computers and I’ve had a fuck full of this already.
Please don’t go saying save zip files and save to whatever because I don’t know anything about them.
I just want a sim I can turn on and fly.
I’m willing to pay anyone who can set this up.
I don’t know anything about setting up computers and I’ve had a fuck full of this already.
Please don’t go saying save zip files and save to whatever because I don’t know anything about them.
I just want a sim I can turn on and fly.
I’m willing to pay anyone who can set this up.
THonestly….
Do you guys have a BestBuy Geeksquad or Computer home set up service place?
You need an ongoing service to deal with potential update/upgrade and maintenance issues so you just need a local service.
The guys there will be killer at not just setting up this rig but if you get some crazy 6DOF they can help with that as well.
IF you can’t do it.. Don’t screw it up messing with stuff.
Just call BestBuy or whatever is local and pay the right people.
Computer set up people will do this easy and fast.
AND if something breaks in an update or some windows 11 bulllllllllll S (don’t get me started)
They are on the hook and only a phone call away to fixing you right up.
That’s the way not just to get flying but to get someone on the hook for keeping you there.
Happy flying brother I can’t wait to see you up there
Do you guys have a BestBuy Geeksquad or Computer home set up service place?
You need an ongoing service to deal with potential update/upgrade and maintenance issues so you just need a local service.
The guys there will be killer at not just setting up this rig but if you get some crazy 6DOF they can help with that as well.
IF you can’t do it.. Don’t screw it up messing with stuff.
Just call BestBuy or whatever is local and pay the right people.
Computer set up people will do this easy and fast.
AND if something breaks in an update or some windows 11 bulllllllllll S (don’t get me started)
They are on the hook and only a phone call away to fixing you right up.
That’s the way not just to get flying but to get someone on the hook for keeping you there.
Happy flying brother I can’t wait to see you up there
QSorry for the noob question. I was altering the settings for the UH-1H (DCS) in TelemFFB and it just closed down. I tried launching it again.. and it closed down after a second on screen... I redownloaded the latest TelemFFB and extracted it and launched it and it closes down after 1 second. I have rebooted and get the same behaviour...
Any ideas? Is there a log file produced to trace these kind of 'behaviours'?
TIA
Any ideas? Is there a log file produced to trace these kind of 'behaviours'?
TIA
QWindows Event Viewer shows the following:
Faulting application name: VPforce-TelemFFB.exe, version: 0.0.0.0, time stamp: 0x6660903c
Faulting module name: Qt5Core.dll, version: 5.15.2.0, time stamp: 0x5fa4dd3b
Exception code: 0xc0000409
Fault offset: 0x00000000000204e8
Faulting process ID: 0x0xCD8
Faulting application start time: 0x0x1DAB9A14F7218D0
Faulting application path: D:\Drivers\VPforce\VPforce-TelemFFB-20240605\VPforce-TelemFFB.exe
Faulting module path: D:\Drivers\VPforce\VPforce-TelemFFB-20240605\assets\PyQt5\Qt5\bin\Qt5Core.dll
Report ID: 14f60150-9d88-42aa-91ab-739578144f0c
Faulting application name: VPforce-TelemFFB.exe, version: 0.0.0.0, time stamp: 0x6660903c
Faulting module name: Qt5Core.dll, version: 5.15.2.0, time stamp: 0x5fa4dd3b
Exception code: 0xc0000409
Fault offset: 0x00000000000204e8
Faulting process ID: 0x0xCD8
Faulting application start time: 0x0x1DAB9A14F7218D0
Faulting application path: D:\Drivers\VPforce\VPforce-TelemFFB-20240605\VPforce-TelemFFB.exe
Faulting module path: D:\Drivers\VPforce\VPforce-TelemFFB-20240605\assets\PyQt5\Qt5\bin\Qt5Core.dll
Report ID: 14f60150-9d88-42aa-91ab-739578144f0c
OI’m struggling to find anyone near me, there are computer shops but nothing around to help with the simulator set up.
I’m in the uk.
I’m in the uk.
Sim trying to print the files for the design by protomaker and the first few printed good but now for some reason my nozzle keeps running into the infill i tried recalibrating the printer and changing the offset but its still happening does anyone know a possible fix?
TYou can tag him @Subsonic and see if he has any suggestions as for your printer and/or print material (rolls).
Otherwise I’m sorry to hear that man hopefully they can sort it out and get you back on track
Otherwise I’m sorry to hear that man hopefully they can sort it out and get you back on track
Si figured out a solution using gyroid infill seems to fix the problem
.is that temp for the (y) axis normal ?
.it goes up to 63 C during combat
WYep, completely normal
PWould there be a reason why my x axis seems to be the most susceptible to instability? if it's ever an effect that causes a motor self protect it's always affecting the x axis. I can send pics of settings.
Pok I keep getting x axis shut down in the kiowa. it happening when using telemffb. I've gone through & set effects down fairly low I'm not sure why it's still occurring. Could my overall settings be affecting telemffb & stability? I have always had to have inertia & friction set rather low, like 10% in settings & 10% in effects tab in config app.
Pok ETL effect is the cause. I had it on 20% it is now on 5% I'll test again
Pmy constant & periodic effects are set at 50% in config app
Pstill happened at 5%
W@PiNKMuD can you show your VP config settings?