I appreciate it. Man this is finiky at this point I’m just gonna stop with the rhino in msfs. All it

I appreciate it. Man this is finiky at this point I’m just gonna stop with the rhino in msfs. All it works now but yea the actual accuracy of it in sim is terrible compared to having it bound in sim. So frustrating

MMistic I appreciate it. Man this is finiky at this point I’m just gonna stop with the r...

Number481•7/2/24, 9:12 PM

After a quick scan through the T6A manual, it seems as if it is using an external flight model and control mapping (the latter of which I have never seen before). TelemFFB relies heavily on default Simvar data for its operation. When one-off “outside the norm” aircraft are developed, all bets are off.

The manual explicitly states:

The tablet takes the place of the corresponding default MSFS configuration, control mapping, and failures screens.
The corresponding MSFS options controls are not compatible with the ADV system.

The tablet takes the place of the corresponding default MSFS configuration, control mapping, and failures screens.
The corresponding MSFS options controls are not compatible with the ADV system.

That probably also means that reading/writing the standard simvar stuff will have unpredictable results.

nubbins•7/2/24, 10:57 PM

@walmis sorry for the ping. Do you know what would cause "grindiness" under heavier (50%+) spring force, at the outer edges of Y axis movement? Can it be the belt? With my hand on the belt, the roughness seems to originate there and feel almost like it is slipping teeth slightly. And only happens on the rebound to center, never on the way out; also it is very noticeable on one side of the belt ("upper" side on one side of the motor pulley), never even slightly on the belt on the other side of the pulley.

nubbins•7/3/24, 4:37 AM

I'm thinking it HAS to be belt related from the way it feels/sounds/behaves. Unless it's motor itself (god forbid).

Nnubbins I'm thinking it HAS to be belt related from the way it feels/sounds/behaves. Unl...

Hiob•7/3/24, 8:25 AM

Apart from checking for any loose parts (pulley, shaft screws, cables) I haven't much ideas right now. How dows it feel, when you loosen the tension on the belt a bit?

Hiob•7/3/24, 8:27 AM

And how does it feel when you reduce the spring gain by 50% (just as a test)

Hiob•7/3/24, 8:28 AM

If the motor was faulty, the gain shouldn't have any influence. I think.

Nnubbins I'm thinking it HAS to be belt related from the way it feels/sounds/behaves. Unl...

Kowalsky•7/3/24, 10:49 AM

Have you checked the small pulley bolt?

lolof1•7/3/24, 10:53 AM

@walmis

HI .

I received my #order and I’m very very happy .
Thank you so much .
But In the box Is there something forgotten?
Is this the part #Machined Aluminum grip?

lolof1•7/3/24, 10:53 AM

Llolof1 @walmis HI . I received my #order and I’m very very happy . Thank you so much...

walmis•7/3/24, 10:54 AM

Hi, it's mounted for your convenience

lolof1•7/3/24, 10:56 AM

But I don't have the part?

lolof1•7/3/24, 10:57 AM

Forget In the box

lolof1•7/3/24, 10:57 AM

lolof1•7/3/24, 10:57 AM

sorry to bother you

lolof1•7/3/24, 10:59 AM

You forgot, I sometimes put the part in my delivery box

lolof1•7/3/24, 10:59 AM

Kowalsky•7/3/24, 10:59 AM

haha

It's already mounted on top of your gimbal

lolof1•7/3/24, 11:02 AM

@Kowalsky

Hi .

I understand now ,sorry with My idiot question

lolof1•7/3/24, 11:07 AM

@walmis
Sorry lol

lolof1•7/3/24, 11:44 AM

My brain is tired

lolof1•7/3/24, 11:45 AM

https://tenor.com/view/squidward-throw-away-brain-spongebob-gif-12540895558420688599

Tenor

HHiob Apart from checking for any loose parts (pulley, shaft screws, cables) I haven't...

nubbins•7/3/24, 4:02 PM

Belt tension doesn't change how it behaves

nubbins•7/3/24, 4:03 PM

Lower spring force will gradually remove the grindiness altogether but that's somewhere below 50%

KKowalsky Have you checked the small pulley bolt?

nubbins•7/3/24, 4:04 PM

yes grub screws are fine, I'm on different pulleys now but with exact same symptoms

walmis•7/3/24, 4:45 PM

How does it feel if you turn the motor pulley without the belt?

Wwalmis How does it feel if you turn the motor pulley without the belt?

nubbins•7/3/24, 5:25 PM

hmmm I haven't tried with the motors energized yet

nubbins•7/3/24, 5:25 PM

When not energized, the motor pulley obviously cogs but some cogs feel bigger than others if you get what I mean

nubbins•7/3/24, 5:26 PM

I have some new 465 and 420 belts coming in tmr but I'm starting to doubt they will change anything

Wwalmis How does it feel if you turn the motor pulley without the belt?

nubbins•7/3/24, 5:35 PM

wait this is a really good point, I haven't tried doing this yet with the gain turned up

walmis•7/3/24, 5:38 PM

I kinda doubt it's the motor, but worth to check

Hiob•7/3/24, 5:40 PM

I have the same effect on my MFG Crosswind FFB Mod. Everything goes smooth, unless I increase the gain too much, than it starts to feel grainy. The belt is not slipping though….

Hiob•7/3/24, 5:40 PM

So I‘m really interested in the conclusion to this issue. Haven’t had any similar problems on the Rhino though.

HHiob So I‘m really interested in the conclusion to this issue. Haven’t had any simila...

nubbins•7/3/24, 6:37 PM

It's demoralizing as hell trying to wade through this alone, lol

nubbins•7/3/24, 6:37 PM

I hate dealing with novel issues

Nnubbins It's demoralizing as hell trying to wade through this alone, lol

Hiob•7/3/24, 6:40 PM

Yes, I feel you. Unfortunately it is hard to remote diagnose a problem. As I said, I kind of know what you experience. I think I had similar with my pedals. For me it was solved via a well tuned software profile.

HHiob Yes, I feel you. Unfortunately it is hard to remote diagnose a problem. As I sai...

nubbins•7/3/24, 6:42 PM

also pondering whether it's a bad size pairing between both pulleys and belt

nubbins•7/3/24, 6:42 PM

But then again, everyone following protomaker would have the same problem, and they don't

Hiob•7/3/24, 6:45 PM

@nubbins Maybe it is a bad pairing between spring gain and belt tension?

Hiob•7/3/24, 6:45 PM

I doubt that it is the „kind“ of belt or pulley

Hiob•7/3/24, 6:46 PM

You could also try to lower the LPFs, that helped me, too.

slowmover•7/3/24, 7:39 PM

Hey mates. Anyone here flying chinook on msfs? i am having truble with trim.

slowmover•7/3/24, 7:39 PM

i do not know how to set the magnetic trimm to hold the cyclic in place

Sslowmover Hey mates. Anyone here flying chinook on msfs? i am having truble with trim.

Number481•7/3/24, 8:58 PM

shouldn't be any different than any other helo in MSFS. Should only need to set up the force-trim feature in TelemFFB. https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/edit#heading=h.jihp5ivlqxj6

Newer screenshot of the same settings:

slowmover•7/3/24, 9:01 PM

hmmm i do not see that settings.let me check it fast

slowmover•7/3/24, 9:04 PM

ok my fault i was not switch the tab to helicopter

Sslowmover ok my fault i was not switch the tab to helicopter

Number481•7/3/24, 9:09 PM

Yeah, make sure when you load an aircraft that TelemFFB does not have a pre-defined profile for, that you hit the big purple button and create a new profile with the right aircraft type. That is the only way that TelemFFB knows what settings to show you and which effects to enable.

HHiob You could also try to lower the LPFs, that helped me, too.

nubbins•7/3/24, 10:01 PM

what do the LPFs do? I haven't touched any of the advanced stuff in the sidebar yet

Wwalmis How does it feel if you turn the motor pulley without the belt?

nubbins•7/3/24, 11:37 PM

yeah, no problem with motor while energized, max master gain and spring force about 65% spring force

nubbins•7/3/24, 11:37 PM

it is difficult to turn, but I was able to get it to the same points in the axis and both the outward movement and rebound are smooth

nubbins•7/3/24, 11:37 PM

it must be the belt or some issue with sizing on either pulley then

I appreciate it. Man this is finiky at this point I’m just gonna stop with the rhino in msfs. All it

Similar Threads