Hmm, you can try USBDevView (https://www.nirsoft.net/utils/usb_devices_view.html) Try uninstalling (

Hmm, you can try USBDevView (https://www.nirsoft.net/utils/usb_devices_view.html)
Try uninstalling (using the right click menu) all VPforce devices (with VendorID FFFF)

NirSoft

View any installed/connected USB device on your system

USBDeview is a software that lists all USB devices that connected to your computer, and allows you disable, enable or uninstall them.

EEraseri @walmis I have problem with the VPForce Configurator. It crashes every time when...

walmisOP•7/22/24, 6:38 AM

Also try different USB ports

Wwalmis Hmm, you can try USBDevView (https://www.nirsoft.net/utils/usb_devices_view.html...

Eraseri•7/22/24, 7:16 AM

I sorted by VendorID and uninstalled all FFFF vendor devices using the USBDevView. I also rebooted and repeated the process few times. Tried different USB-ports too. Unfortunately it didn't help.

If I start Joystick VPForce configurator and then plug in pedals, the joystick configurator stays alive. I can then also open the pedal-configurator as separate window. However, if I choose joystick from VPForce configurator query it crashes the configurator

The attached image is what I see from USBDevView after uninstalling and re-installing the Rhinos.

Nnubbins @walmis do you think the motor reclibration procedure could help with the belt g...

hexpod•7/22/24, 2:58 PM

You could first detach the motor in order to see if once powered the shaft moves perfectly smoothly

SSynoxys Hi all, just recently completed my DIY rhino build and I am experiencing an issu...

hexpod•7/22/24, 3:08 PM

I am experiencing small but noticeable torque steps on one axis as well the other being perfectly smooth. Let me know if you find an overcome

Synoxys•7/22/24, 3:10 PM

My issue was resolved by walmis performing a remote recalibration of the affected motor.

hexpod•7/22/24, 3:10 PM

Ok thanks for the info!

Synoxys•7/22/24, 3:10 PM

Np!

mattback•7/22/24, 3:35 PM

Hello, I just got my rhino, i am trying to use the virpil VFX ( f14 ) grip with it. are there any special drivers i need to install for the VFX grip to communicate with the rhino? i have some basic functionality but i am wondering about the twist axis , it seems like buttons go crazy when i twist the axis.

Mmattback Hello, I just got my rhino, i am trying to use the virpil VFX ( f14 ) grip with...

LeLv30_Superbus•7/22/24, 3:39 PM

Just checking: You did select this grip didn't you?

mattback•7/22/24, 3:40 PM

where do i do that ?

mattback•7/22/24, 3:40 PM

do i do that inside VPForce configurator?

LeLv30_Superbus•7/22/24, 3:40 PM

yes

mattback•7/22/24, 3:41 PM

oh geez

mattback•7/22/24, 3:41 PM

it was righ tthere in front of me

mattback•7/22/24, 3:41 PM

i just hit reset config and now my stick isn't auto-centering the way it did when i first plugged it in

LeLv30_Superbus•7/22/24, 3:42 PM

calibrate it again

mattback•7/22/24, 3:42 PM

now it seems like my left and right is backwards

mattback•7/22/24, 3:43 PM

when i stick to the left, the blue dot goes to the right

mattback•7/22/24, 3:43 PM

when i stick to the right, the blue dot goes to the left

LeLv30_Superbus•7/22/24, 3:43 PM

so which way is your emergency stop button, towards you or your monitor?

mattback•7/22/24, 3:44 PM

i steop is towards me

mattback•7/22/24, 3:44 PM

E stop button is towards me

LeLv30_Superbus•7/22/24, 3:45 PM

what about these

mattback•7/22/24, 3:45 PM

mattback•7/22/24, 3:45 PM

theyre not inverted

mattback•7/22/24, 3:46 PM

my force comp are both zero though

LeLv30_Superbus•7/22/24, 3:46 PM

and you already calibrated it again right

mattback•7/22/24, 3:47 PM

i'll do it again right now

LeLv30_Superbus•7/22/24, 3:47 PM

remember to STORE settings

LeLv30_Superbus•7/22/24, 3:48 PM

you can test with Apply

LeLv30_Superbus•7/22/24, 3:48 PM

then store if you're happy

mattback•7/22/24, 3:48 PM

i pressed auto calibrate, then i pressed ok, then i moved stick forward and back a few times and left and right a few times to the maximums, then i pressed auto calibrate again, then i pressed store

mattback•7/22/24, 3:48 PM

was that incorrect? up and down is correct, left and right is backwards

mattback•7/22/24, 3:49 PM

now, if i click " axis invert " it works fine

mattback•7/22/24, 3:49 PM

axis invert, apply settings / store settings

LeLv30_Superbus•7/22/24, 3:50 PM

movement ranges and directions are OK now?

mattback•7/22/24, 3:51 PM

yes.

mattback•7/22/24, 3:51 PM

but theres no auto centering happening now

mattback•7/22/24, 3:51 PM

did i need to check something for auto centering?

LeLv30_Superbus•7/22/24, 3:51 PM

Good. I don't understnd why you had to invert if your e-stop if facing your way, though.

mattback•7/22/24, 3:51 PM

mattback•7/22/24, 3:52 PM

i should have never pressed " reset config " i wonder if that has something to do with it

LeLv30_Superbus•7/22/24, 3:52 PM

There is no spring force? Can you show your settings

LeLv30_Superbus•7/22/24, 3:52 PM

ah your spring is at 0%

mattback•7/22/24, 3:53 PM

i didn't adjust any of that... i accidentally pressed " reset config " thinking maybe that's why my axis wasn't working correctly on my vfx grip

LeLv30_Superbus•7/22/24, 3:53 PM

Just put Spring slider to 100% for now and start playing with the others

mattback•7/22/24, 3:54 PM

am i allowed to play with them? i don't want to break this thing

mattback•7/22/24, 3:54 PM

i just waited a year... i flew one time with it and fell in love

LeLv30_Superbus•7/22/24, 3:54 PM

also you have a pot which you can set to control Spring (most have it that way if they have only one)

mattback•7/22/24, 3:55 PM

yes, when i first flew it yesterday, the knob potentiometer to the left of the e- stop was like a simple volume / gain knob

Hmm, you can try USBDevView (https://www.nirsoft.net/utils/usb_devices_view.html) Try uninstalling (

Similar Threads