@walmis do you think the motor reclibration procedure could help with the belt grinding issue? perha

@walmis do you think the motor reclibration procedure could help with the belt grinding issue? perhaps related to anti-cogging not working optimally?

nubbinsOP•7/21/24, 8:36 PM

I just finished my 4th (5th?) rebuild, with again all new belts and pulleys, and the grinding issue has persisted

Ice•7/22/24, 12:59 AM

Is there anyway to stop my Rhino from rocketing forward when my pilot crashes our shared aircraft in DCS?

Ice•7/22/24, 1:00 AM

If I don't have my hand on the stick when it happens, my stick just absolutely piss missiles itself into the forward end stop and I'm afraid it's gonna break something. No damage so far and I've been much more careful about it.

Ice•7/22/24, 1:01 AM

To avoid it, when I'm not flying, I just turn the master gain in the software to 0% so I can still use buttons bound to the stick. But I was wondering if there's another solution to this issue. It's very easy to reproduce, just crash an aircraft into the ground in DCS hard.

IIce If I don't have my hand on the stick when it happens, my stick just absolutely p...

Bozo VFA-86•7/22/24, 2:48 AM

Do you run telemffb with decel effect selected?

BBozo VFA-86 Do you run telemffb with decel effect selected?

Ice•7/22/24, 3:03 AM

yes

Bozo VFA-86•7/22/24, 3:05 AM

i think if you de select that , it will stop doing it

Bozo VFA-86•7/22/24, 3:07 AM

there is also an option in the dcs special menu for the f4 about the wso controls but im not sure what it does

Ice•7/22/24, 3:51 AM

I think that fixed it

Eraseri•7/22/24, 5:52 AM

@walmis I have problem with the VPForce Configurator. It crashes every time when I start configuring joystick when there are two Rhinos connected. I think I screwed up something when setting up the USB ID's for the devices. Separately both devices work fine. Attached is demonstration video of the problem. Attached is also the settings for the Joystick.

I have tried changing USB ID's for both devices to no avail.
I have also removed Rhino from device manager but it didn't help either.
I have also reset both Rhinos completely using the "Reset config" button but it didnt help.

TelemFFB thinks both Rhinos are fine and I have used them simultaneously while flying. I have, however, encountered some weird behavior with joystick but I'm not sure whether its related to this

EEraseri @walmis I have problem with the VPForce Configurator. It crashes every time when...

walmis•7/22/24, 6:33 AM

Hmm, you can try USBDevView (https://www.nirsoft.net/utils/usb_devices_view.html)
Try uninstalling (using the right click menu) all VPforce devices (with VendorID FFFF)

NirSoft

View any installed/connected USB device on your system

USBDeview is a software that lists all USB devices that connected to your computer, and allows you disable, enable or uninstall them.

EEraseri @walmis I have problem with the VPForce Configurator. It crashes every time when...

walmis•7/22/24, 6:38 AM

Also try different USB ports

Wwalmis Hmm, you can try USBDevView (https://www.nirsoft.net/utils/usb_devices_view.html...

Eraseri•7/22/24, 7:16 AM

I sorted by VendorID and uninstalled all FFFF vendor devices using the USBDevView. I also rebooted and repeated the process few times. Tried different USB-ports too. Unfortunately it didn't help.

If I start Joystick VPForce configurator and then plug in pedals, the joystick configurator stays alive. I can then also open the pedal-configurator as separate window. However, if I choose joystick from VPForce configurator query it crashes the configurator

The attached image is what I see from USBDevView after uninstalling and re-installing the Rhinos.

Nnubbins @walmis do you think the motor reclibration procedure could help with the belt g...

hexpod•7/22/24, 2:58 PM

You could first detach the motor in order to see if once powered the shaft moves perfectly smoothly

SSynoxys Hi all, just recently completed my DIY rhino build and I am experiencing an issu...

hexpod•7/22/24, 3:08 PM

I am experiencing small but noticeable torque steps on one axis as well the other being perfectly smooth. Let me know if you find an overcome

Synoxys•7/22/24, 3:10 PM

My issue was resolved by walmis performing a remote recalibration of the affected motor.

hexpod•7/22/24, 3:10 PM

Ok thanks for the info!

Synoxys•7/22/24, 3:10 PM

Np!

mattback•7/22/24, 3:35 PM

Hello, I just got my rhino, i am trying to use the virpil VFX ( f14 ) grip with it. are there any special drivers i need to install for the VFX grip to communicate with the rhino? i have some basic functionality but i am wondering about the twist axis , it seems like buttons go crazy when i twist the axis.

Mmattback Hello, I just got my rhino, i am trying to use the virpil VFX ( f14 ) grip with...

LeLv30_Superbus•7/22/24, 3:39 PM

Just checking: You did select this grip didn't you?

mattback•7/22/24, 3:40 PM

where do i do that ?

mattback•7/22/24, 3:40 PM

do i do that inside VPForce configurator?

LeLv30_Superbus•7/22/24, 3:40 PM

yes

mattback•7/22/24, 3:41 PM

oh geez

mattback•7/22/24, 3:41 PM

it was righ tthere in front of me

mattback•7/22/24, 3:41 PM

i just hit reset config and now my stick isn't auto-centering the way it did when i first plugged it in

LeLv30_Superbus•7/22/24, 3:42 PM

calibrate it again

mattback•7/22/24, 3:42 PM

now it seems like my left and right is backwards

mattback•7/22/24, 3:43 PM

when i stick to the left, the blue dot goes to the right

mattback•7/22/24, 3:43 PM

when i stick to the right, the blue dot goes to the left

LeLv30_Superbus•7/22/24, 3:43 PM

so which way is your emergency stop button, towards you or your monitor?

mattback•7/22/24, 3:44 PM

i steop is towards me

mattback•7/22/24, 3:44 PM

E stop button is towards me

LeLv30_Superbus•7/22/24, 3:45 PM

what about these

mattback•7/22/24, 3:45 PM

mattback•7/22/24, 3:45 PM

theyre not inverted

mattback•7/22/24, 3:46 PM

my force comp are both zero though

LeLv30_Superbus•7/22/24, 3:46 PM

and you already calibrated it again right

mattback•7/22/24, 3:47 PM

i'll do it again right now

LeLv30_Superbus•7/22/24, 3:47 PM

remember to STORE settings

LeLv30_Superbus•7/22/24, 3:48 PM

you can test with Apply

LeLv30_Superbus•7/22/24, 3:48 PM

then store if you're happy

mattback•7/22/24, 3:48 PM

i pressed auto calibrate, then i pressed ok, then i moved stick forward and back a few times and left and right a few times to the maximums, then i pressed auto calibrate again, then i pressed store

mattback•7/22/24, 3:48 PM

was that incorrect? up and down is correct, left and right is backwards

mattback•7/22/24, 3:49 PM

now, if i click " axis invert " it works fine

mattback•7/22/24, 3:49 PM

axis invert, apply settings / store settings

LeLv30_Superbus•7/22/24, 3:50 PM

movement ranges and directions are OK now?

mattback•7/22/24, 3:51 PM

yes.

mattback•7/22/24, 3:51 PM

but theres no auto centering happening now

mattback•7/22/24, 3:51 PM

did i need to check something for auto centering?

@walmis do you think the motor reclibration procedure could help with the belt grinding issue? perha

Similar Threads