[12:50:07.751] * USB Connected [12:50:07.921] Reset Motor:7 [12:50:07.921] Motor 0 active [12:50:07.

[12:50:07.751] * USB Connected
[12:50:07.921] Reset Motor:7
[12:50:07.921] Motor 0 active
[12:50:07.921] Motor 1 active
[12:50:07.921] Motor 0 timeout
[12:50:07.921] Motor 1 timeout
[12:50:07.921] Motor 0 active
[12:50:59.624] Config received
[12:51:25.215] Config received
[12:51:28.389] Config received
[12:51:28.393] Config written to flash
[13:18:39.957] Reset Motor:7

DDARRYL [12:50:07.751] * USB Connected [12:50:07.921] Reset Motor:7 [12:50:07.921] Motor...

Number481•9/21/24, 7:30 PM

Looking closer at your screenshot, it appears the issue is with the X motor connection. Double check the connection between the x motor and the control board?.

As a test I bet if you disabled the X axis, you would see data from the Y axis

DARRYLOP•9/21/24, 7:32 PM

I will try that test. Then I will remove the base screws and check x (roll) motor connections. Back in a few.

NNumber481 Looking closer at your screenshot, it appears the issue is with the X motor conn...

DARRYLOP•9/21/24, 7:38 PM

Disabling X and then calibrating gave some kind of values to the Y (instead of just blanks), but it was garbage jittering all over the place and didn't respond to axis motion at all. Will unscrew base bottom now.

NNumber481 Looking closer at your screenshot, it appears the issue is with the X motor conn...

DARRYLOP•9/21/24, 7:57 PM

The motor-end connections appear fine. Green light on both motors and board. Motor data connectors plugged into the correct board ports per the assembly instructions. I'm stumped. Back in 15.

CapnFlint•9/21/24, 7:58 PM

Is there a wiring diagram for the VKB mount adapter anywhere? I had my mount in a bad place and pinched some wires that I need to re-solder

CapnFlint•9/21/24, 8:05 PM

Specifically is it white or black that needs to be resoldered to the blank pin here?

CCapnFlint Is there a wiring diagram for the VKB mount adapter anywhere? I had my mount in ...

walmis•9/22/24, 10:45 AM

The yellow wire is signal

Gunnergolly•9/22/24, 2:53 PM

VPforce FFB Configurator is no longer auto switching profiles whenever i swap between aircraft in DCS. i.e. if i was flying the F-4E and then changed over to the F-14 in my next session, i now have to "alt-tab" out of the game and manually"import" the F-14 profile. It used to automatically change over ..... any ideas ???.

GGunnergolly VPforce FFB Configurator is no longer auto switching profiles whenever i swap be...

CapnFlint•9/22/24, 3:04 PM

Isn’t the auto switch a function of TelemFFB, not the configurator?

Wwalmis The yellow wire is signal

CapnFlint•9/22/24, 3:11 PM

Got it working, thanks!!

CCapnFlint Isn’t the auto switch a function of TelemFFB, not the configurator?

Gunnergolly•9/22/24, 3:27 PM

Yeah TelemFFB is auto switching between profiles ok but VPforce no longer is ???..

Bob Bushman•9/22/24, 3:34 PM

The configurator never had auto switching, it was always telmeffb.

Gunnergolly•9/22/24, 4:26 PM

That's strange, for the the past month up until this morning my configurator was changing profiles ???. Which was great, now i have to change the aircraft profile manually, which is no big deal as i only ever really play the same three modules..... but having the automation was nice whilst it lasted :)...

Fr4Ged•9/22/24, 4:29 PM

you can set and adapt profiles in TelemFFB which is way better in my opinion because it changes profiles automatically.

Gunnergolly•9/22/24, 4:41 PM

Yeah i notice in TelemFFB that there is a configuration override option where you can adjust the spring, damper, master gain etc etc. The trouble is that i make use of a feature called "Gain map" within the configurator "effects" tab where i can adjust the spring gain curve of the "aileron" individually for instance. My preference is to generally set the pitch axis spring gain to feel stonger than the aileron axis as i prefer a lighter feel on the ailerons.

Bob Bushman•9/22/24, 4:42 PM

There's also a spot where you can select a vpconf file to load.

Gunnergolly•9/22/24, 5:25 PM

Yeah that's what i've been using over the past month, my understanding was that i can configure my profile to my liking in VP configurator and then tell TelemFFB to load that profile for that particulur aircraft. It's been working fine up to now, however it dosen't seem to be doing that anymore . Whatever profile i have imported in to VP Configurator is the one that it will continue to use regardless if i change my aircraft in DCS to a helicopter, WW2 bird or a jet..... i need to investigate this further and maybe try and uninstall/reinstall TelemFFB again.... somethings amiss here...

GGunnergolly Yeah that's what i've been using over the past month, my understanding was that ...

Number481•9/22/24, 5:47 PM

Check the log. If there’s an issue loading or finding the file, it will tell you.

smitty•9/22/24, 6:55 PM

also, while playing the game telemffb has to remain running, but configurator does not.

Cajun•9/22/24, 7:18 PM

Need help I'm getting this error

Cajun•9/22/24, 7:25 PM

superbird1011•9/22/24, 7:47 PM

I unplugged my vpforce for a moment as it was conflicting on a game, now i'm back flight simming and i get this and no feedback at all. i have updated telemffb, i have tried multiple planes, restarted msfs twice and started in the correct order. And reset effects

CCajun Need help I'm getting this error

smitty•9/22/24, 8:27 PM

when you open configurator, does it present you a selection like this? then, enter your numbers in telemffb

NNumber481 Check the log. If there’s an issue loading or finding the file, it will tell y...

Gunnergolly•9/22/24, 8:32 PM

Yeah that was the problem, for some reason it was no longer recognising my .vpconf files in their original location. Moved them elsewhere and TelemFFB is now loading them ok..... thanks for everybodies input

Ssmitty when you open configurator, does it present you a selection like this? then, e...

Cajun•9/22/24, 8:33 PM

No, only in telemffb but can't open it anymore

smitty•9/22/24, 8:34 PM

might be a usb issue if none of the apps see it

Cajun•9/22/24, 8:34 PM

I entered the wrong PID. Is there a way to delete and start over

smitty•9/22/24, 8:36 PM

you can edit the numbers in regedit

Cajun•9/22/24, 8:36 PM

Thanks will try it

smitty•9/22/24, 8:38 PM

to really start over, you can delete that whole TelemFFB registry folder (its only for the system settings, your planes and profiles are stored elsewhere)

Cajun•9/22/24, 8:38 PM

It worked. Thanks so much

VKNG•9/23/24, 2:43 PM

Does anyone ever have problems with the buttons not all working on your stick?

VVKNG Does anyone ever have problems with the buttons not all working on your stick?

kaltokri•9/23/24, 2:47 PM

No. Which Stick do you have? I use a Thrustmaster Warthog Stick and all is working.

VKNG•9/23/24, 2:49 PM

Winwing stick with attachment

VKNG•9/23/24, 2:50 PM

to make it work. most buttons work but not all. guess i’ll have to get a TM. Seems something is always up with the winwing and the vp force unless i’m doing something wrong in the configurator

walmis•9/23/24, 3:09 PM

Which buttons do not work? WW F-16EX?

Wwalmis Which buttons do not work? WW F-16EX?

VKNG•9/23/24, 3:23 PM

Yea F16EX. I will have to check the WW simapppro and find the exact button numbers but the gray (trim) hat switch in all 4 directions plus pressing down doesn’t work. As well as the black 4 way hat switch below it and to the left of it. But again i will have to get back on here in a bit and see which exact buttons don’t work.

VVKNG Yea F16EX. I will have to check the WW simapppro and find the exact button numbe...

TheAmazinGreat•9/23/24, 3:57 PM

Have you tried using the option for hats as buttons? Either checked/unchecked.

TTheAmazinGreat Have you tried using the option for hats as buttons? Either checked/unchecked.

VKNG•9/23/24, 4:21 PM

I will try that here shortly and report back. Thanks!

VVKNG Yea F16EX. I will have to check the WW simapppro and find the exact button numbe...

walmis•9/23/24, 4:27 PM

Also make sure to select WW adapter grip profile

Wwalmis Also make sure to select WW adapter grip profile

VKNG•9/23/24, 4:28 PM

I just saw that in the manual as well! Thank you! I will check the manual better next time before reaching out.

Absolutely love my Rhino!

Wwalmis Also make sure to select WW adapter grip profile

VKNG•9/23/24, 5:58 PM

This was it! Thanks again!

Marsvinet•9/23/24, 7:29 PM

I had a look around and I could not find an answer, only somebody asking a similar question before: I can not get the configurator to recognize the brake lever as well as some of the buttons on my first generation T-50CM, when using the T-50CM2 grip type. Is there any workaround, or solution?

MMarsvinet I had a look around and I could not find an answer, only somebody asking a simil...

TheAmazinGreat•9/23/24, 9:14 PM

@Touch_Of_Legend may be able to help if not Walmis himself

MMarsvinet I had a look around and I could not find an answer, only somebody asking a simil...

Touch_Of_Legend•9/24/24, 10:58 AM

I’m using that grip (Virpil CM not the CM2) but I’m not home at the moment.

I remember you have to select the CM2 and someplace in the configurator you select (something) and it brings up the box so you can calibrate the brake lever as Axis.

I got it all working great but it’s been awhile since I did it so it “might” be in my previous posted comments or else I’ll try to dig the info out for ya later today

Chubb•9/24/24, 3:45 PM

Hello all. I have been having a problem with the Rhino.
Sometimes when I start DCS, the stick loses all motor function untill I reboot DCS and the telemffb software.

Also, when flying the Apache in DCS, if change seats to the gunner position and spend too much time without using the stick, when I return to the pilot's seat the stick is dead as well.

How do I go about determining if this is a Windows issue, DCS issue or otherwise in the software?

The only steps i have taken so far is to verify that USB Selective Suspend is disabled

TTouch_Of_Legend I’m using that grip (Virpil CM not the CM2) but I’m not home at the moment. I r...

Marsvinet•9/24/24, 3:46 PM

If it is the boxed option, then that is the problem, it reads no raw value, so calibrating it yields no result. The raw buttons are recognized, but the configurator isn't picking them up as the Virpil axis. One of the 4 way hats is also not recognized

Marsvinet•9/24/24, 3:47 PM

Funnily enough, if I set the grip type to VPC V.F.X, it recognizes all buttons and the lever is assigned as the twist axis

CChubb Hello all. I have been having a problem with the Rhino. Sometimes when I start ...

Hiob•9/24/24, 4:49 PM

Do you hear the disconnect chirp?

MMarsvinet Funnily enough, if I set the grip type to VPC V.F.X, it recognizes all buttons a...

TheAmazinGreat•9/24/24, 5:05 PM

I’m sure you could use it this way, doesn’t have to be bound as twist in game.

[12:50:07.751] * USB Connected [12:50:07.921] Reset Motor:7 [12:50:07.921] Motor 0 active [12:50:07.

Similar Threads