i like that your stick returns smoothly at center. how did you achieve that?
i like that your stick returns smoothly at center. how did you achieve that?
DJust finished my build.
Unfortunately i get the following:
"[17:24:06.018] * USB Connected
[17:24:06.029] Motor 0 timeout
[17:24:06.029] Motor 1 timeout"
both motors appear offline.
They have power. I get see them both having green flashing led.
Unfortunately i get the following:
"[17:24:06.018] * USB Connected
[17:24:06.029] Motor 0 timeout
[17:24:06.029] Motor 1 timeout"
both motors appear offline.
They have power. I get see them both having green flashing led.
FMy guess is that applying some damper helps.
FBesides their power cables did you connect their data cables too?
Dyep
FA picture of the board may help. I'd try disconnecting and reconnecting the data cables in both the motors and board just to make sure they are connected correctly.
DTy. Give me some time to unscrew the front cover
DDid that and one of them worked. But the other one is still offline. seems that the connectors are a bit loose
DWell, it seems that the jst pins inside the connector had moved slightly outwards. i fixed the connector and now it works ok.
DThanks
L@walmis
Thank you so much ,
my Rhino work very well ,I Apply /6hz in #Expert Settings -Damper Force LPF
Thank you so much ,
my Rhino work very well ,I Apply /6hz in #Expert Settings -Damper Force LPFDI have another issue, trying to do the first calibration.
I'm with protomaker's design.
In the pdf it says:
(with the stick centered - i'm using the centering tool)
------
My process is as follows:
X,Y values are all 0
I push "Auto Calibrate"
X,Y values become the following:
Xmin=14, Xmax=14
Ymin=1171, Ymax=1172
raw_x=14, raw_y=1172
I set X,Y values as:
Xmin=0, Xmax=4096
Ymin=0, Ymax=4096
I push "Auto Calibrate" again
Apply Settings and Store Settings
raw_x and raw_y on the left panel haven't changed.
raw_x = 14 and raw_y=1172
and the joystick indicator has the dot somewhere in the top left range
I'm with protomaker's design.
In the pdf it says:
(with the stick centered - i'm using the centering tool)
- Click "Auto calibrate"
- In the axes setup set Xmin,Ymin=0 Xmax,Ymax=4096
- Click again "Auto calibrate" and then "Apply settings" and "Store settings"
------
My process is as follows:
X,Y values are all 0
I push "Auto Calibrate"
X,Y values become the following:
Xmin=14, Xmax=14
Ymin=1171, Ymax=1172
raw_x=14, raw_y=1172
I set X,Y values as:
Xmin=0, Xmax=4096
Ymin=0, Ymax=4096
I push "Auto Calibrate" again
Apply Settings and Store Settings
raw_x and raw_y on the left panel haven't changed.
raw_x = 14 and raw_y=1172
and the joystick indicator has the dot somewhere in the top left range
FAfter auto calibrate I click store settings not apply settings.
FAnd remember to move the stick to the max positions after hitting auto calibrate.
FAnd then once you move the stick to the max positions you hit store settings.
Dso i remove the centering tool during the process? in the pdf it says to do that afterwards
DI'll try again like you say
DStill doesn't work.
DIf I alter the X,Y min max values to 0 and 4096
raw_x and raw_y values become like i said
raw_x and raw_y values become like i said
DIf i don't and just push Auto calibrate once, move the stick to max positions and click again, then joystick indicator is correct but still raw_x and raw_y are not 2048 at the center and values are way off the 0-4096 range
FYou don't need the centering tool. Just remove it. Select auto calibrate. Move the stick to its maximum making circles or squares and then select store settings.
FDon't worry about the values. Just make sure it works.
FI never had to enter any values manually. I just did a couple of auto calibrations and then it was ready.
Dwhat about this part of the manual?
FI honestly didn't do any of that. Just a regular auto calibration a couple of times and it worked.
DThank you. I'll do it that way for the time being, but if anyone knows please give me an update.
@Subsonic (Protomaker) Is it something that should be updated in the manual? I'm following the instructions line by line.
@Subsonic (Protomaker) Is it something that should be updated in the manual? I'm following the instructions line by line.
FOnce it is calibrated you don't need to do it again. It's set and ready to go
DI'm still curious though 
LHi @Dimitris
I’m a noob as you with my #Rhino
I Read too the Manual PDF.
For have Axes:
Click in :
-Vpforce FFB Configurator / Settings / import /Rhino-defaults.vpconf and you click = open here
I’m a noob as you with my #Rhino
I Read too the Manual PDF.
For have Axes:
Click in :
-Vpforce FFB Configurator / Settings / import /Rhino-defaults.vpconf and you click = open here
L
LAnd you going in #Settings/ click : Apply setting.
In Vpconfigurator /Settings /Damper Force LFP/ change 8Hz to 6hz .
In Vpconfigurator /Settings /Damper Force LFP/ change 8Hz to 6hz .
LAnd it’s all
L
L
FMy guess is that those steps are to reset everything before a calibration to avoid any issues.
LYes .
And he read my explain
And he read my explain
LI a noob as @Dimitris with my #Rhino
LAnd now this afternoon my Rhino work very well
Vcan someone tell me what the Z is i cannot seem to find what it is but its always doing input making it hard to configure axis settings
FWhich grip are you using and which grip is selected in the configuration?
SNothing to change. That is best practice, relayed to me by the man himself.
DYes, but it didn't work for me. I followed your steps line by line
Draw x,y values never landed at 2000 range
Vusing a warbrd and i chose warbrd
NZ is usually the twist axis. If you don't have the version of the grip with the twist axis, you don't need to worry about it
Vis there a way to disable this cause it always saying im using the Z axis
FHave you tried doing a calibration in windows? Since there will be no input in the z axis maybe it will center it for you.
Press Windows Key + R, type joy.cpl and press enter.
Select the controller on the list > Properties > Settings tab > Calibrate
Press Windows Key + R, type joy.cpl and press enter.
Select the controller on the list > Properties > Settings tab > Calibrate
Vi mean i have the twist axis but i dont want to use it sorry i should have said that
FCalibrate the twist axis in windows. That should center it.
Vthank u will try
SWorked for me every time
My current raw values are 1870 and 2390
My current raw values are 1870 and 2390