That‘s why I designed my own limiter, I couldn’t stand the noises. Unfortunately my solution isn’t p
That‘s why I designed my own limiter, I couldn’t stand the noises. Unfortunately my solution isn’t parametric and only serves my special needs…
WI have a 3D printer to make new ones but haven’t got into design yet. I don’t know why it’s designed like this, I saw the gap before I put them in and thought that was odd.
HI think it‘s designed as a two piece so that you can change it without disassemble the grip. However even as two part there would be better solutions (putting the divide in the corners and make them overlap). But in a second step I simply made it one piece.
WYeah, I was thinking corners. Do you have a stl file for your version and what angles are they? I wonder if I can reduce the issue with some tape perhaps.
HI need to search….somewhere I have it…..
WWell for now I put a strip of the thick heavy duty black Gorilla tape I had around where the stick touches the limiter inside and it worked, much better, no noises or perceivable changes in smoothness going past the halfway point either side. Will have to see how it lasts. The limiters really need a redesign though.
E577 Rhinos to go!
CYou will see time will fly by and you get your Rhino !
V:package: 
RHINO #0746 Has Shipped!
RHINO #0746 Has Shipped!
*Do you guys have strange increasing pitch oscilation when flying turboprops in MSFS (Blackbird Texan T6A)? Seems like a exponentially more powerfull springey effect every swing... if I would not calm it by hand it would amplify and go nuts... Is that normal pitch behaviour...?
*It's like it reacts to its own swing with a more powerfull spring swing in opposite direction... 
*talked with a PC-9 pilot... aaand this behaviour is not normal and does not exist... what values should I monitor when experiencing this? so i can tone them down in profile...
TProbably a good start would be to post screenshots of your settings and effects tabs in the VPF configurator
NThis has been an issue with the dynamic forces for MSFS forever. Particularly with fast, sensitive aircraft. I have some ideas to address but haven't gotten around to it.
Some things you can do to try to alleviate the worst of it:
- Enable some dampen effect or increase the strength if its already enabled
- Reduce constant force strength.
Some things you can do to try to alleviate the worst of it:
- Enable some dampen effect or increase the strength if its already enabled
- Reduce constant force strength.
*I put video and screenshot of settings in support channel...
MHi, how do you guys get an idea how much queue there is for you?
MDo you get your order number after some time after sending the form?
AMThx
MSeems like only a year of wait then 
MAre you printing metal? Are household printers suitable for that?
FIirc qr4rigs stuff is 3d printed as well
FAnd dont underestimate 3d prints, some materials go crazy
MYeah I know, just asking if this is realistic to make at home
MHehe I checked and those printers are size of a room
FFor metal, yeah
FIts either SLS or basically a robot welding machine
FI'm using Geeetech's PETG as filament and I'm printing with a Bambu Lab P1S - so nothing really fancy. I did the Departed Reality motion platform with that PETG and had no issues. For the quick releases it seems to work fine also as long as the devices produce forces in given directions or produce only limited forces. The only thing I found that will not work are handbrakes - too big forces in undefined directions.
V:package: 
RHINO #0749 Has Shipped!
RHINO #0749 Has Shipped!V:package: 
RHINO #0750 Has Shipped!
RHINO #0750 Has Shipped!
YAccording to the bot when inquirinf about status, my turn has come, but i havent received any email yet. Am i missing anything on how to pay and confirm the order?
HYou should get a call for action by walmis once your ticket is due.
FCheck spam folders and ask the bot
YThank you very much for your replies
TBeen using the Rhino with a VKB MCGU stick for a little while now and really enjoying it.
I recently added a 10cm extension to it, with a 17 degree limiting plate that's working fine.
I've been trying to adjust the forces to make it feel the same as it did when I had no extension, but I still find it harder to be quite as accurate around the center as I did with no extension. Maybe I'm not as accurate simply because my hand doesn't notice as much of an angle change near the center with the extension for the same percentage of stick motion without an extension?
Anybody else noticed this, or have suggestions on how to change settings when going from no extension to having an extension?
I recently added a 10cm extension to it, with a 17 degree limiting plate that's working fine.
I've been trying to adjust the forces to make it feel the same as it did when I had no extension, but I still find it harder to be quite as accurate around the center as I did with no extension. Maybe I'm not as accurate simply because my hand doesn't notice as much of an angle change near the center with the extension for the same percentage of stick motion without an extension?
Anybody else noticed this, or have suggestions on how to change settings when going from no extension to having an extension?
HShould be quite the opposite. The longer the throw the more fine control you have. You probably just need to adjust to the longer travel for the same angular displacement.
TI should have been more specific. The throw has actually been reasonably similar between my previous setup (VKB MCGU on Gunfighter base with a 20cm extension), the VKB MCGU on the Rhino base with no extension but no limiter, and the VKB MCGU on the Rhino base with a 10cm extension and 17 degree limiter. Hence why I'm wondering if it's more the difference in angle or FFB resistance near the center that's the issue. Or it may just all be in my head! 
HMemory of fine motor skills are mighty. Give it a few sessions or couple of days and you will adapt.
HMake sure to reset all curves and saturation to default in the axis settings.
Ngood lord
Ndropped 340 places in a month??
NNeed someone to take over my spot lol
N143 left
HMoza Hype.
HYou don’t need to take it. Once it‘s your turn, you can select to not take it.
MYeah I dropped 70 rhinos today
MHow does that work? I thought like 2 are shipped a day
Speople cancle their orders
MBut so many of them?
Sit was much higher back when Moza and Winwing announced their FFB sticks
SI dropped about 200 spots in a single day, then again the next week
