scaling option only allows you to increase movement virtually not take any movement out
scaling option only allows you to increase movement virtually not take any movement out
TYou need to leave the max where it is and decrease the min to move the center to desired value
THave you tried putting in negative numbers? You can for some things so I figured you could for axis scaling. Make sure to unlink the values so they aren’t all the same.
Tonly allows positive numbers
TActually I don’t think you need to use negative number in axis scaling. I think you would need 75% in backwards axis scaling
TBecause your stick thinks it physically needs to move 20deg to get to the end stop. But if you axis scale 75% it should only have to move 15 degrees to get to the virtual end stop.
Tno if I put 75 in the bottom that will give me 100 percent pull when im only at 75 physcially
TI just don't think there is away to get this to work I believe you must have asymmetric center not really a option to get this to work which is ok I will have to live with it the way it is
TI think there is, I just don’t know if I am explaining it right.
TIt doesn't work how you are explaining it. I understand exactly what you are trying to say. I have just tried it and it doesn't work that way.
Taxis scaling will only scale the virtual axis so that when you are physically at lets say 5 deg pos Y you can scale it to make the software think you are at 100
Tit doesnt work any other way
TChanging the raw values does move the stick to the desired center position though?
Tno changing the value on the max just shortened my axis so that i'm at the virtual limit before I hit physical limit but did not change the virtual or physical center
Tit stayed the same stick didn't move at all
TWhen you push the stick forward does raw Y increase or decrease?
TI think I'm done messing with it. I will have to live with the stick being at center a little forward than I want it to be unfortunately,
Tfoward is -
TRaw Y decreases with forward
TCorrect?
TBased on how you said you were changing the max earlier I don’t think you were moving things correctly. And to say that forward is - confrims that I think.
TCan you post a screenshot of your effects and settings tabs with the stick held at the desired center point? Please include the calibration values as part of the screenshot on the settings page.
Ti have the desired center point at 1627 and when i center the stick where i want it the raw read 1627
Tok it did physically move my stick back towards me
Tbut there is no way to scale it now
Tcannot add negative and messing with the back scale only changes the stick back
TWhen you push it all the way forward does it hit the virtual stop when the stick hits the physical stop?
When you pull it back, you should get about 75% virtual for 100% physical, does this happen?
When you pull it back, you should get about 75% virtual for 100% physical, does this happen?
Tno when I pull stick it virtual and physicall axis is perfect
Tnow when i push stick the virtual axis is way to senstive stick only moves a little forward and hits virtual limit way to fast
Tscaling only increase the problem there is no option for negative scaling of the axis only increase the virtual movment
TYou’ve changed the wrong calibration value then. You said you decreased the max but you need to decrease the min.
TSet max back to where it was
Tok i recalibrated I'll change the min now
TWhat this will do is allow 20deg fwd to be at 100%, and 20deg back to be at 100%. But you have a 15 degree limiter on the back so when you pull back to 15 degree limiter your virtual axis should be at 75% travel.
Tit's working you are a genious
T
Tsorry I know that had to be very painful for you.
Tlol
THaha it’s all good, it was more just starting to question my own sanity lol.
TDid the axis scaling work to get it to be 100% when you pull back?
Tyes it all works
TAwesome, glad to help!!
Tyes I'm so thankful. This will be alot more comfortable for me
Tamazing how much a few degrees will do.
DHas anyone else lost engine input to their VP force rino with the newest IL2 patch? I still get gunfire rumble and can feel flaps, and gear etc. Its just the engine
GHey everyone. Has anybody tried their Rhino or the VP software with MSFS2024?
OYes
OMy stick works fine, no FFB obviously.
OFeels good still.
GThat's great to hear. Hopefully, Walmis will have some time to see about getting FFB working. Thanks!
Auhh, you should be able to use TelemFFB to get FFB in MSFS2024