Si am not sure what is this.can you point me
W
S
S
Sthere is a huge difference between mine and yours
Wcould you try to set FPS limit in DCS to something like 60, I'm trying to understand whats' hanging the GUI mainloop in telemFFB
Sgive me a sec i am trying to find that
Sok limit set to 60FPS testing now
S
Snow it works walmis
Sbut even with 60FPS limit i do not get your results
SMy specs i7-10700k 64ddr4 4080Super
Sand i always set it 180FPS vener changed it
Wso it's not hanging when fps is limited?
Sexactly is work fine now
Seven with 120FPS
WOkay, good to know
WI'll make some optimizations
H@walmis I may add a data point here. I always use (and recommend) external fps limiter (Afterburner/Rive in my case). My ingame is also set to 180 fps (default), but I'm factual limited to 120 fps by Aftrerburner.
Si set back to 180 FPS and it works now 
if you see i get around 140FPS and when i switch back to telemFFB windowd DCS is at 60FPS. i am not sure if this help you
if you see i get around 140FPS and when i switch back to telemFFB windowd DCS is at 60FPS. i am not sure if this help you
HI found the ingame limiter to be wonky in the past and therefore choose to not use it
HPart of the reasoning is, that the ingame fps limit is governed by the main render thread on the CPU. I found it should have better things to do than limit the fps. Better leave that to the GPU driver or similar.
RHaving some issues getting FFB Configurator to apply changes. Button remapping not taking. Any tips?
RUsing powered usb hub
FAre you hitting store too? So the settings stay saved in the device after a reboot or reconnect.
RYes. Not getting any results in my joystick tester, it worked before I tried changing the VPforce device name (I have several grips I plan to use)
R
Rno buttons register in VPC tester
RF18 name shows in JoyIDs but not in VPC
Rbuttons ARE recognized in VPF
R
Woh damn, I think I've made a bit of an issue in the latest beta
RF18 name now showing in VPC but still no buttons
Rfor remapping?
Wstandby, will fix it in a bit
PI have a question about the VP MOD that I installed on the Virpil Ace pedals. Do you know if the brake pedals don't work when using the Mod? It's like the brake signal isn't being read by the VPForce program... or did I do something wrong?
NIf you are referring to my mod design, there is no electrical connection between the pedals and the VPforce control board. The brakes still need assigned from the virpil pedals, not from the "vp force" pedals.
In order to get the brakes into the VPforce board, you would need to re-wire from the brakes to the analog inputs on the board (and probably would have to replace the hall sensors with ones that provide analog output as I am pretty sure they are digital).
In order to get the brakes into the VPforce board, you would need to re-wire from the brakes to the analog inputs on the board (and probably would have to replace the hall sensors with ones that provide analog output as I am pretty sure they are digital).
WFix pushed
Rfirmware prob, not w/ configurator?
Rthanks!
NI have seen similar lagging in the settings page on a couple of occasions and never been able to pinpoint what is going on . For me, running in python native, when it happens, it seems to be tied to the virtual environment of whatever branch/pycharm project I am running. When it happens, if I start from a different project, or from an exe build, it is perfectly fine.
Seems like it might be a deep PyQT issue more than a logic issue.
Seems like it might be a deep PyQT issue more than a logic issue.
R@walmis paddle button on RealSimulator extension flashes on/off. ideas?
HMaybe I am to stupid.... For allowing Trim and Autopilot functions in MSFS the manual says, I have to remove any binding in MSFS or SPAD.NXT. But after removing that functions and enabling it in the VP Force Software, Joystick, Collective and Rudder are not connected to the sim. What do I wrong?
Sturn on axis control switch? telemffb acts like SPAD.
R@walmis regarding the flashing paddle button, I have confirmed it works properly with a RS base and works properly over Bluetooth with my Virpil CM3 base.
RBefore you did the Firmware update this morning, it worked as a solid ON button, so something you did may have had an unintended consequence
WPushed an update, hopefully this will fully fix it
HDid that and I got no control in game 
RUnfortunately not
Sthats like the opposite of what should happen..
