Not that I noticed...very much not a force feedback type feel...I'll check the manual.
Not that I noticed...very much not a force feedback type feel...I'll check the manual.
BIt doesn't. It always feels the same.
TRoll force is lighter than pitch force.
BWhen you're flight control laws blend into normal law after take off the pitch becomes a G load demand and roll becomes a roll rate demand.
KMentour Pilot on YouTube said Aibus are developing it to get both synchronized movement between the sticks and ffb.
KI wonder if they will try a side yoke as well?
HAnd roll has asymetric force, needs more force inwards than outwards
SStill wish somebody had a rhino Profil to simulate an airbus sidestick :crycat:
Nlooking at the video above.. just seems like fairly light spring force and a shit ton of damper?
Aiirc the stick is supposed to go stiff when you engage autopilot
Athe airbus sidestick
BWhat? No, it doesn't. That's probably more likely to do with our musculature and how it's easier to make an inward movement compared to outward.
BYes, that's true. The rudder pedals stiffen up on an autoland with rollout guidance too iirc (it's been a while since I checked that ). In fact , I think they stiffen up when you engage the autopilot. I never have any rudder input when I engage the autopilot so it's not something I've noticed.
HThe exactly why they do it, needs more force inward as it's easier to pull inward and vice versa
BReally? I've never noticed that. I'll pay closer attention to that next time I do the flt control check.
HWhat I could find:
Breakout force: 1.1 pounds
Pitch: Fore and aft. +/- 16 degrees 22.5 pounds
Roll: Outboard 20 degrees 5.6 pounds.
Roll: Inboard 20 degrees 7.8 pounds.
Breakout force: 1.1 pounds
Pitch: Fore and aft. +/- 16 degrees 22.5 pounds
Roll: Outboard 20 degrees 5.6 pounds.
Roll: Inboard 20 degrees 7.8 pounds.
BOh wow, that must be in some kind of maintenance manual. It's not in the FCOM, is it?
Aso are we getting stiff sticks in our buses at some point?
RI noticed when in the 64 and not flying, my stick doesn't move. I wonder, how possible is it that when the stick is folded (controls handed off to other pilot), the ingame cyclic will effect the position of the Rhino?
AYes it's like that. Try to deflect with the "wrong" hand, and you'll notice.
E#0841 is being enjoyed. Thank you!
OOooh yehhhh 69 rhinos to go
A69 orders of rhino on the wall, 69 orders of rhino
MHi all…….just trying to make sense of the VPF control board……in this pic posted below…….can someone answer the 2 questions I have? Ta
T
MThanks <@TheAmazinGreat>
![SR-F_Winger_[73]_David](https://cdn.discordapp.com/avatars/98037306870472704/f924b51d2e4486c1eb873c2f4fb7f6a3.webp?size=40)
SReminder for everyone that might still BE looking for a Xmas Present. One Monster Rhino Base ready to put Motors in is available. PM for Details:
S
FThe most appreciated Christmas present ever received, thank you very much Walmis 
EHi everybody! Just got a Rhino from a teammate and i'm struggling to set up the software properly. I red the manual but there are tons of options and it's overwhelming... I fly mainly warbrids. Before the rhino i had an arduino controlling a motorized pulley that stiffened or loosed the joy depending on airspeed (dcsbios telemetry). The joy was loose on the ground and on top of a loop or hammerhead and very heavy in a dive. So far i've played with many settings especially the new g-forces in vpforce telem but for my geelings the delta between the minimum and maximum forces is too small.. In particular i feel a light stick before the take off run... but once in flight stick gets heavy and stay heavy even on top of a hammerhead with propeller on idle and less than 50mph... Without air hitting control surfaces my understanding is that they should be light as while on the ground... Any tips on were to start? Can someone share their warbirds profiles? Ty in advance and merry Christmas and great flights!
FAre you using telemffb? Or just the dcs force feedback effects?
Etried both!
FYou may want to post pictures of your configuration to see if maybe something there needs to be adjusted
FThe tabs in the vpfprce configurator
NMerry Christmas 
SMerry Xmas Folks. Have a good time
GWaiting for a new mount - state of the art 1995 v 2025:
CBack in the 90‘s I had the full set. TM stick, throttle and pedals. Now the memories come up again 
SHow strong should cyclic control stick forces be set in the AH-64D and Huey to best simulate RL?
FI mean I am pretty sure you don't really have any forces in the stick of at least the Apache. So basically just the force trim and maybe a slight rumble
KHi folks! Been on the list now for a while and am curious about the product. I currently use a VKB gunfighter base with a MCG-U stick, using a 100/200mm extension depending on the plane. Has anyone here made the jump from my setup over to the Rhino FFB?
KFrom what I understand, you can adjust the feedback pretty easily between different airframes. How much of a hassle is it to switch between different profiles? Let’s say I like flying 200mm on warbirds but then switch to 100mm for a jet, and a different profile for helos. Is this all doable?
KFinally, what software controls the grip config? Would I still use VKB’s software for the grip itself, and Rhino for the base?
KOh, also, does anyone here desk-mount their base? Is that doable?
FI believe you can configure the program to load different profiles based on the aircraft, so the only "hassle" would be to switch the extensions. This isn't that bad, as the vkb adapter has an external wire so you only have to swap the physical connection. You are also correct that you keep the vkb software for the grip.
FLastly, there have been a few that desk mounted, but they made a slight modification to support the mount from the floor as well. You can find some examples here, use the discord search to make it easier.
KNice, thanks!
Bshould have some transitional flutter between flight and hover, handy way to tell where you are in the transition or if you are getting slow without having to constantly stare at the speed indicator.
SThe question is whether the cyclic stick movement on either axis requires more that fingertip pressure.
FOh, gotcha