what settings were used? I want to add a bit of a steep angle to my spring gain to make hold the cen

what settings were used? I want to add a bit of a steep angle to my spring gain to make hold the center easier, as the adaptive centering isnt strong enough for my needs and extension length. I still get osciallation, they are better after newest update, but still present.

ReedOP•1/3/25, 11:27 PM

ReedOP•1/3/25, 11:30 PM

ReedOP•1/3/25, 11:30 PM

RReed what settings were used? I want to add a bit of a steep angle to my spring gain ...

smitty•1/4/25, 1:20 AM

Try dropping Spring dependent damping. I see you have it kinda high at 80%.

ReedOP•1/4/25, 1:37 AM

Mike T•1/4/25, 2:40 AM

Hi, got the shift register board.....looking for sockets to solder on them......is it the JST-PH 2.0 size used for these? Found some PH 2.0 plugs and sockets on Amazon and want to check before purchase. Ta

mark turner•1/4/25, 6:59 AM

Also damping slider very high. Will post my settings shortly

mark turner•1/4/25, 8:12 AM

ReedOP•1/4/25, 12:50 PM

@walmis what are the default settings for Max motor current and Max PSU current with your rhino? I feel like I purchased mine about two years ago.

neok•1/4/25, 9:44 PM

hey there, is there a way to rotate x and y axis 20 deg to the left?

neok•1/4/25, 9:45 PM

in the software somewhere?

neok•1/4/25, 9:45 PM

so that pitch up is pulling back and slightly right?

ono•1/4/25, 11:49 PM

Hello, is a PowerSupply with 19,5v and 9,3a 180w compatible, or is 20v a must have? Thank you

Oono Hello, is a PowerSupply with 19,5v and 9,3a 180w compatible, or is 20v a must ha...

Prometheus [Prom]•1/5/25, 12:21 AM

totally fine

PPrometheus [Prom]totally fine

ono•1/5/25, 12:26 AM

Thanks

ono•1/5/25, 12:10 PM

Hello, I wonder if the better ventilation is to be expected when vacuuming or blowing in the fan

ReedOP•1/5/25, 6:54 PM

where are you all buying custom length cable for connecting rhino to virpil/tm grips? I need a solution, vs diy if available.

RReed where are you all buying custom length cable for connecting rhino to virpil/tm g...

Stal2k•1/5/25, 7:33 PM

This isn't a bad option if you don't want to fool with DIY. The price is cheap enough that you can pretend you aren't also getting an aluminum tube

https://mfg-sim.com/warthog-extensions/mfg-warthog-extension.html

MFG

MFG Aluminum Warthog Extension

Compatible with Warthog, Cougar and Moongos T-50 joystick In aluminum or anodised black color Improve aiming accuracy and ergonomics of your joystick

Trooper 311•1/5/25, 8:01 PM

where is the best place to download sofeware for the rhino

smitty•1/5/25, 8:05 PM

if "best" means "only", then the best sites are:
https://vpforcecontrols.com/usb/rhino/ for configurator
https://github.com/walmis/VPforce-TelemFFB for telemffb

GitHub

GitHub - walmis/VPforce-TelemFFB: DCS FFB Telemetry Effects (for VP...

DCS FFB Telemetry Effects (for VPforce FFB). Contribute to walmis/VPforce-TelemFFB development by creating an account on GitHub.

Trooper 311•1/5/25, 8:07 PM

i did an update and now it say wrong version what should i do

smitty•1/5/25, 8:07 PM

update of what? screenshot

Trooper 311•1/5/25, 8:09 PM

Trooper 311•1/5/25, 8:09 PM

smitty•1/5/25, 8:10 PM

download 1.0.17b2 from https://vpforcecontrols.com/usb/rhino/

Trooper 311•1/5/25, 8:10 PM

i did not sure why this is happening

smitty•1/5/25, 8:11 PM

your configurator screenshot shows 1.0.16. run the 1.0.17 version

SStal2k This isn't a bad option if you don't want to fool with DIY. The price is cheap e...

ReedOP•1/5/25, 8:12 PM

I found several that are 12cm or less. I need a length of 30cm, lol

Trooper 311•1/5/25, 8:13 PM

yes

Trooper 311•1/5/25, 8:21 PM

Tried several times to update not working

C4N4DN•1/5/25, 9:08 PM

Hey guys. I have a early rhino and im starting to get a bit of play only in the pitch axis. Its about 1/8inch only in one axis about the neutral position. Is there any way i can tighten this back up?

C4N4DN•1/5/25, 9:08 PM

C4N4DN•1/5/25, 9:11 PM

@walmis

Chris•1/5/25, 10:50 PM

It looks like your printed mount for the aluminum is broken. There is a split which opens when you press the stick forward. Look closely to the corner nearest to the camera and you will see it.

C4N4DN•1/5/25, 11:16 PM

I think thats just a reflection of the light. The piece in person is solid as a rock

f14billy•1/6/25, 12:00 AM

Try grabbing the printed part and see if the play is in the metal shaft. If so try tightening the 4 screws that keep it in place and see if that helps. Also the screws that keep the big pulley in place may be loose.

Oono Hello, I wonder if the better ventilation is to be expected when vacuuming or bl...

Prometheus [Prom]•1/6/25, 12:21 AM

usually blow, you want positive pressure in the case…much as with PC cooling design….opinions can vary however

Ff14billy Try grabbing the printed part and see if the play is in the metal shaft. If so t...

C4N4DN•1/6/25, 12:40 AM

The movement is between the printed shaft and the top pitch gimbal.

C4N4DN•1/6/25, 12:41 AM

When you move it fwd and back the pitch wheel doesnt move at all.

elijahautistic•1/6/25, 12:51 AM

Hello ! I am new on the project and i am doing my research to make a rhino on my own, but i can't really find anyone talking about making the base with 86BLF04 motors instead of the 57BLF03.
Is there any reason why ?

CC4N4DN When you move it fwd and back the pitch wheel doesnt move at all.

f14billy•1/6/25, 2:01 AM

I'd try tightening the screws in the middle of the big pulley. I think there's 5 or 6 of them and see if that makes a difference

Eelijahautistic Hello ! I am new on the project and i am doing my research to make a rhino on my...

f14billy•1/6/25, 2:02 AM

The 86 motors would require a stronger gimbal and bigger housing. They have more torque and handle overheating better but the build will be significantly more expensive.

Ff14billy The 86 motors would require a stronger gimbal and bigger housing. They have more...

elijahautistic•1/6/25, 2:10 AM

Okay ! I've seen some things like monster rhino and stuff, but do you know if anyone shared some files to make a base with the 86 ? or i'll have to modify it

Eelijahautistic Okay ! I've seen some things like monster rhino and stuff, but do you know if an...

f14billy•1/6/25, 2:13 AM

Yes the files are available for the housing and a couple of gimbal options. Hope someone can link them to you. I just had my parts made by @SR-FWinger[73]_David since I didn't want to go through the hassle of it

CC4N4DN When you move it fwd and back the pitch wheel doesnt move at all.

f14billy•1/6/25, 2:14 AM

Also if tightening the screws that connect the pulley to the ball bearings doesn't fix it you will have to take the bottom wall out and maybe even remove the motors to see if you can tighten the screws that put the gimbal together.

Ff14billy Yes the files are available for the housing and a couple of gimbal options. Hope...

elijahautistic•1/6/25, 2:15 AM

Okay thanks ! I will search for it then, thanks for your help :)

Eelijahautistic Okay thanks ! I will search for it then, thanks for your help :)

f14billy•1/6/25, 2:22 AM

It you decide to do it yourself make sure the front 80mm fan is 5v and not 12V or it won't be able to cool those big motors well. Big difference in cooling them.

Ff14billy It you decide to do it yourself make sure the front 80mm fan is 5v and not 12V o...

elijahautistic•1/6/25, 2:23 AM

5v instead of 12v ? Wouldn't the 5v be less powerful ?

f14billy•1/6/25, 2:29 AM

The board provides 12v so the 5v would spin way faster. Just have a spare in case it dies faster lol. I have no issues at all.

f14billy•1/6/25, 2:30 AM

In the configuration it's set to only send 70% max so it works great.

what settings were used? I want to add a bit of a steep angle to my spring gain to make hold the cen

Similar Threads

Similar Threads

Similar Threads