Give me a rough measurement of the diameter of the plug part
Give me a rough measurement of the diameter of the plug part
Vwill do one moment
Wand the threads diameter on the male part
Waliexpress.com
Smarter Shopping, Better Living! Aliexpress.com
V14.5mm Thread Diameter
V9
Vmm
W@vulkan607 perhaps you have a multimeter ? 
One missing piece of information is the pinout from the VKB grip contact PCB -> 4 wire connector mapping. That could be found out with continuity test.
One missing piece of information is the pinout from the VKB grip contact PCB -> 4 wire connector mapping. That could be found out with continuity test.Wah, nvm, found it!
W
TI'm excited by this VKB progress, I better start saving up.
VIndeed, I was ready to switch to a TM grip if It meant using this base
Vbut now I dont have to im very happy
WThe only downside is the dangling wire that will go out of the adapter base 
TAre the base and the grip seen as two different controllers?
Wfor VKB - yes
WVKB decided to encrypt the communication with the Grip
TSo you could put one of those cable fittings in the base for the VKB blackbox, then the wire would be inside the base?
BThat's a radio mike connector - still, it's not a bad solution at all, I use them myself on my projects sometimes - poor person's Amphenol 
- still, it's not a bad solution at all, I use them myself on my projects sometimes - poor person's Amphenol 
JI am a bit confused. On the connection diagram the PSU is connected to MOT1 and Motor 2 to PWR. Is this correct?
The motor wires are blue and yellow. Which wire is + and which -?
The motor wires are blue and yellow. Which wire is + and which -?
Wah, it doesn't matter, but thanks for noticing. The power is distributed equally to those 3 ports.
Wpositive is the yellow wire
W
Wprototyping the VKB adapter
OThat looks really good.
W
WAnd voila - real deal 
F
Fhow does the vpforce compare to the Brenner? I have no idea what the Brenner's internals are
SLook up the conversation, there's a review as well about it too comparing both pros and cons
SThis one
FIs that mine?
WI'm making some in advance
WBut yes, you can say that
F
VDude the CNCed adaptor mount looks so good. It's crazy how low the price you charge for them is.
WI think I'll go with 25β¬ final price if bought with the rhino, they require a bit of work, but very reasonable price for CNCed composite part.
Nis the design still with a seperate connection or did you reach an understanding with either VKB or their connection?
SSo if you go the vkb route you'll need the grip, Blackbox and electronics too? So basically everything but the gimbal And it'll run on the exterior of the stick.
SAttention to this folks
SSo anybody who wants to use with VKB grip will need to hook separately with a blackbox
PAre there any commercially available desk mounts that would accommodate a Rhino unit well?
KJust found this randomly browsing YT. Seems like a super cool project. How will it integrate with DCS? Does this face the same problems that Brunner has with only reading certain parameters from a lua or will this access all the data from all the modules?
WThe base itself is quite high, so better to attach to the floor/seat than use long and possibly wobbly desk extensions
WThanks! It integrates natively to dcs (and other titles such as IL2) like a msffb2. It's possible to use lua to augment additional effects if desired.
W*
Regarding VKB - yes you will need to connect to the black box. This is a solution for those who have existing VKB systems and don't want to switch over to TM/Virpil.
Regarding VKB - yes you will need to connect to the black box. This is a solution for those who have existing VKB systems and don't want to switch over to TM/Virpil.
εare the arrangement of the screw holes identical to any existing device? I saw on the diagram that the distance btwn the holes are 160 x 160.32 though, they are in mm I guess?
εor perhaps it's possible to direct mount the Rhino onto a aluminum profile structure? consumer center chair mounts are very rear..
WYeah it's 160x160mm. You can definitely make a structure from alu profiles. But it needs to be pretty well attached to something.
WA couple of concrete sidewalk tiles would do the trick also 
εbtw glad to see the VKB grip will soon be supported. nice job man, you are the savior
so WW nxt perhaps?
forgive my greediness
so WW nxt perhaps? forgive my greediness