Minion Working fine Now motor error

how can i correct this?

Klipper reports: SHUTDOWN

TMC 'stepper_z' reports error: DRV_STATUS: 001900d0 s2vsa=1(LowSideShort_A!) ola=1(OpenLoad_A!) olb=1(OpenLoad_B!) cs_actual=25
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown

just happened today, all else was working fine

blacksmithforlife•12/14/22, 10:22 PM

It is saying it has a short. Double check your driver's are seated properly, and double check all the wiring to the steppers

primary-violetOP•12/14/22, 11:07 PM

Thank you i will

primary-violetOP•12/14/22, 11:15 PM

all is good

primary-violetOP•12/14/22, 11:16 PM

odd

primary-violetOP•12/14/22, 11:46 PM

ive tried a new cable, heck ive even reloaded the printer config from scratch, like a new install @blacksmithforlife

blacksmithforlife•12/15/22, 12:19 AM

Well something is causing a short. So check all wiring again

primary-violetOP•12/15/22, 1:15 AM

Replaced the board and all drivers

primary-violetOP•12/15/22, 1:15 AM

After installing v minion config it is stuck here

primary-violetOP•12/15/22, 1:15 AM

@blacksmithforlife

primary-violetOP•12/15/22, 1:38 AM

After swapping pis and boards

primary-violetOP•12/15/22, 1:39 AM

This is ver. 1.2.4 previous pic 2.0.4 alpha

TThe Space Ape After installing v minion config it is stuck here

blacksmithforlife•12/15/22, 2:17 AM

Back up, did you install the firmware and do all the necessary configuration?

primary-violetOP•12/15/22, 2:17 AM

Of course , this is my third printer not my first

TThe Space Ape Of course , this is my third printer not my first

blacksmithforlife•12/15/22, 2:20 AM

Got to cover the basics, many people miss those steps

primary-violetOP•12/15/22, 2:20 AM

Im with ya

primary-violetOP•12/15/22, 2:20 AM

I ordered a new board , the “new board “ i had had dim led lights

blacksmithforlife•12/15/22, 2:20 AM

Did you work through all the steps in the pinned message?

primary-violetOP•12/15/22, 2:20 AM

New drivers 2209 v1.3

blacksmithforlife•12/15/22, 2:21 AM

ratos-supportfrequently asked questions - MCU connection issues

primary-violetOP•12/15/22, 2:21 AM

I have 2 pis a 3 and a 4 both no lick

primary-violetOP•12/15/22, 2:21 AM

All of this was previously working

primary-violetOP•12/15/22, 2:21 AM

I have to wait for the new board

blacksmithforlife•12/15/22, 2:22 AM

Well you changed PIs and board, so you can't just swap things around like that and expect it to still work

blacksmithforlife•12/15/22, 2:25 AM

When you replace a main board you have to reinstall the firmware, but before you can do that you need to recompile the firmware.

primary-violetOP•12/15/22, 2:35 AM

Yes all that has been done in order

primary-violetOP•12/15/22, 2:35 AM

I think the “new” replacement board is bad at this point

primary-violetOP•12/15/22, 2:36 AM

The old board lights up new one does not

primary-violetOP•12/20/22, 10:47 PM

Got this fixed , bad board.

Minion Working fine Now motor error

Similar Threads

Similar Threads

Similar Threads