Im going to add a 35cm curved extension to mine
Im going to add a 35cm curved extension to mine
SWithout an extension the stick ends up as far from the mounting point as a virpil with an extension. So then you have to put the rhino close to the floor
DI have this in my possetion, has someone here tried to adapt a real helicopter grip to his base? (Rhino or not)
D
D
NHow tall is this unit?
D
MWeird looking ceiling lamp :p
MOh now I see, it's for an Australian helicopter
Pdepending on the weight of your grip that's going to be a lot of leverage, I have the VKB MCGU on the 200mm curved extension & I don't think you'd want to go any higher with the same sort of weight.
RI'll be using a virpil alpha.
R
PWith the vkb 200mm extension the RHINO feels really nice still, with the less heavy KG12 grip on it's definitely a noticeable difference in feel but I can adjust this in the VPforce settings, I use the grips in different planes too so the settings are different.
R44cm from top to bottim
RI only fly helicopters.
Rwalmis said it would be ok
PIf you can wire the buttons, HAT's, switches to one of Walmis's shift registers then it should talk to the RHINO base fine
PHave you decided where you'll mount the RHINO? it's a fair bit larger than other bases, you may only need a 200mm extension if the RHINO end up higher when it's mounted
RWHats dimensions from floor to top of grip adapter?
Poh & this is a total game changer when it comes to flying heli's in sim!
ROn the floor where the current stick is, it's gopt about 6inches of space below it
RI can shim up or down as needed
RI can also cut the extension down, too. Its just bent alum.
Pfrom base to vkb adapter is like 30cm/1ft
Pthere are dimensions in the faq channel
PDimensions are in the faq channel, but it's about 30cm/1ft from bottom of base to the top of the grip connection
R11,414, I assume is inches?
Pif that's 11.414 then yeah it'd say it's inches
RI might need to cut an 1" off my extension, which is totally fine
Pyeah the RHINO compared to other bases already feels like it has a 100mm extension, but as you would know flying heli's you want that extension
RIt's going to be great.
F
F#0038 has arrived to its owner yesterday :)
FVery good packaging, no damage during transport. Looks very well built and sturdy.
FUnfortunately its going to be at least 1-2 weeks before I can dedicate some real time to this baby.
FThanks @walmis 
WAwesome! Thanks for the update
JWalmis, your policy on not taking payment until you gave all parts in stock is great. I wonder though, would it help you scale up production if you asked for payment earlier, even if just for a partial amount as a deposit? I for one would be willing to pay all or part of the cost of my order much earlier, if it would help you to build up your business and increase production rate. I know this might not be possible or practical for every customer, but I would bet many of us would support this model given your proven ability to deliver on your commitments.
SI think thats the path to stress and anxiety for walmis. Even if he hires more people they are not as likely to be effective ( he has to train them) and he makes less money (he has to pay them)
JAs I understand it adding on more people will take time and would not result in an immediate increase in production. He has mentioned previously he does have plans for increasing production over time, so perhaps we'll see some of that come into place later this year.
JIndeed, you may be right, and my comment was intended more as an offer than as a suggestion, as I'm sure Walmis knows best how he wants to run his business.
MYes, and for that you can jumpstart the project by modding an MSFFII, which already has the architecture. Changing current sensing circuit and adding caps/diodes/mosfets you can get it up to respectable torque ranges.
Brushed motors are definitely inferior to brushless though, and unless you have a cheap source of skewed armature motors you aren't really going to save much money. Brushless motors are anti-cogged with software, brushed motors need to natively have minimal cogging hence helical armatures.
You can save a lot of time and hassle to make something much superior with one of walmis's kits.. besides being BLDC there are tons of quality of life features and the components reduced to amazing simplicity
Brushed motors are definitely inferior to brushless though, and unless you have a cheap source of skewed armature motors you aren't really going to save much money. Brushless motors are anti-cogged with software, brushed motors need to natively have minimal cogging hence helical armatures.
You can save a lot of time and hassle to make something much superior with one of walmis's kits.. besides being BLDC there are tons of quality of life features and the components reduced to amazing simplicity
MI don't' think talking about the same motors here lol. With brushed DC for force feedback you need exotic skewed armature types to minimize magnetic cogging vs brushless which can be compensated digitally.
This puts them into a whole different category than generic cheapos on Amazon. Pittman Lo-Cog, Glentec servos are a few I know of offhand. Apparently electric power steering units use some kind as well, though hard to find specs on and specs are needed before you can tailor drives for them. Acquiring suitable motors is the only easy part of a project like this.
Here's what my Pittman motors look like inside. New they are over $200 apiece, smaller ones aren't much cheaper and it's just as much work to make a weak stick as a strong one, cause and the hardware only half the story. I was lucky to find used ones south of $50 ea which are in the voltage/amperage range to use to hotrod MSFFII following Roland van Roy's mod, a project I've abandoned because in the end is a ton of work for comparitively mediocre results. Here's a link to his page if you're really serious about this. Even the best MSFFII hack or full diy roll your own will be a cumbersome dinosaur compared to what you can much more easily make with current brushless options
Full diy: http://www.simprojects.nl/diy_force_feedback_interfacing.htm
msffii hack http://www.simprojects.nl/ms_siderwinder_ff2_hack.htm
..here's a functional digital/analog circuit I came up with for force feedback effects based on telemetry, Roland tested it and I think used it to replace all his LED/LDR circuits that performed a similar function
This puts them into a whole different category than generic cheapos on Amazon. Pittman Lo-Cog, Glentec servos are a few I know of offhand. Apparently electric power steering units use some kind as well, though hard to find specs on and specs are needed before you can tailor drives for them. Acquiring suitable motors is the only easy part of a project like this.
Here's what my Pittman motors look like inside. New they are over $200 apiece, smaller ones aren't much cheaper and it's just as much work to make a weak stick as a strong one, cause and the hardware only half the story. I was lucky to find used ones south of $50 ea which are in the voltage/amperage range to use to hotrod MSFFII following Roland van Roy's mod, a project I've abandoned because in the end is a ton of work for comparitively mediocre results. Here's a link to his page if you're really serious about this. Even the best MSFFII hack or full diy roll your own will be a cumbersome dinosaur compared to what you can much more easily make with current brushless options
Full diy: http://www.simprojects.nl/diy_force_feedback_interfacing.htm
msffii hack http://www.simprojects.nl/ms_siderwinder_ff2_hack.htm
..here's a functional digital/analog circuit I came up with for force feedback effects based on telemetry, Roland tested it and I think used it to replace all his LED/LDR circuits that performed a similar function
MOthers have already spent thousands of dollars and hours solving a lot of problems over the years that anyone coming fresh to this has yet to even discover are a problem yet. That's more what I meant by you aren't gonna save money this route, even if your time is worth nothing to you. If it were as easy as just buying a couple motors on amazon there would have been lots of great diy additions over the years but success in this space is limited to a select few that really knew their stuff and stayed on target.
M...a good starting place to try to get up to speed is the 'Honey' thread Propeller started https://forum.dcs.world/topic/246873-honey-i-developed-ffb-joystick-diy/#comments
ED Forums
Finally, it is time to introduce my FFB joystick prototype! I spent a lot of time and learned a lot of new stuff when work on it. So here what is already implemented: - Works as standard USB FFB device, understands standard FFB protocol. No drivers. No plugins. - Supports spring, constant, ramp a...
MAlso, no one is using steppers. walmis's kit uses Nema23 or Nema34 brushless servos. Steppers are unsuitable for FF
JYouTubeI Build Stuff
In this video I made a working Lego flight stick using a mechanism that moves my mouse.
The flight stick was designed to look like the F-18 stick, just like in Top Gun Maverick. I ended up using the flight stick to play War Thunder, and it worked flawlessly.
Timestamps:
0:00 Intro
0:24 Designing the Mechanism
3:41 Adding the Trigger
4:54 Epic ...
The flight stick was designed to look like the F-18 stick, just like in Top Gun Maverick. I ended up using the flight stick to play War Thunder, and it worked flawlessly.
Timestamps:
0:00 Intro
0:24 Designing the Mechanism
3:41 Adding the Trigger
4:54 Epic ...
DFor those that have the stick, how much play/backlash do you find around center?
SIt depends on the module you're flying or how you have it setup in the app. It's not like a regular spring stick where it can be sloppy, if it's sloppy its because the game is telling it to be sloppy (like a slow flying warbird). I think that is what you're asking?
DNo, there is going to be some play around center due to backlash, curious how much there is.
SSorry then maybe someone else can jump in, I'm not really familiar with backlash. There isn't really any 'play' though, again unless the module wants there to be.