Z_TILT_ADJUST - Impossible to complete.

Hello. since 5 hours I can't handle both with Z_TILT_ADJUST
I checked everything I know, even changed all possible motor connections to Z, Z1, Z2,
LMR
RML
LRM
pe
MLR
MRL

in the first combination the difference goes down but around 5-6 it starts to grow??? and I got the error Retries aborting: Probed points range is increasing

log in the attachment

Z_Tilt_adujust.txt4.47KB

Helge Keck•3/4/23, 6:21 PM

check if your motor couplers are tight

Helge Keck•3/4/23, 6:21 PM

or if the ball screws on the bed are loose

Helge Keck•3/4/23, 6:21 PM

or if your probe is loose

Helge Keck•3/4/23, 6:21 PM

...

Helge Keck•3/4/23, 6:21 PM

also, check with stepper buzzer if the z steppers are connected in the right order

HHelge Keck or if the ball screws on the bed are loose

genius23plOP•3/4/23, 6:56 PM

check if your motor couplers are tight - checked
ball screws on the bed are loose - Checked
your probe is loose - Checked

STEPPER_BUZZ STEPPER=stepper_z2 not working - i changed the cable, changed tmc_2209

genius23plOP•3/4/23, 6:57 PM

But motor moves on Z homing

awake-maroon•3/4/23, 7:07 PM

switching the left and right cable worked for me

IIllyaskja switching the left and right cable worked for me 🙂

genius23plOP•3/4/23, 7:33 PM

I tried every combination of cables and it didn't work

Helge Keck•3/4/23, 7:36 PM

you you need to make sure that all your steppers are in the correct order, not jsut swapping cables and hope the best

Stepper_buzz stepper=stepper_xStepper_buzz stepper=stepper_x
top left stepper

Stepper_buzz stepper=stepper_yStepper_buzz stepper=stepper_y
top right stepper

Stepper_buzz stepper=stepper_zStepper_buzz stepper=stepper_z
bottom left stepper

Stepper_buzz stepper=stepper_z1Stepper_buzz stepper=stepper_z1
bottom rear stepper

Stepper_buzz stepper=stepper_z2Stepper_buzz stepper=stepper_z2
bottom right stepper

Helge Keck•3/4/23, 7:36 PM

first do this, then come back

Helge Keck•3/4/23, 7:36 PM

you execute that command and feel with your finger directly on the motor pulley if the correct stepper buzzes

genius23plOP•3/6/23, 8:53 AM

OK
on x motor moving
on y motor moving
on z left and right they move synchronously and simultaneously
on z1 back motor are moving
on z2 nothing moves nothing happens

Ggenius23pl OK on x motor moving on y motor moving on z left and right they move synchronou...

Helge Keck•3/6/23, 8:54 AM

left and right should not move simultaneously

Helge Keck•3/6/23, 8:55 AM

have you maybe connected on of these steppers to a slave stepper connector?

Helge Keck•3/6/23, 8:56 AM

please show a photo of your board with the stepper connectors

genius23plOP•3/6/23, 8:58 AM

probably not because I don't even know what you're talking about

genius23plOP•3/6/23, 9:00 AM

printer2.cfg21.02KB

genius23plOP•3/6/23, 9:00 AM

here is my printer config

Helge Keck•3/6/23, 9:00 AM

show me a photo of your board with the stepper connectors

genius23plOP•3/6/23, 9:01 AM

Helge Keck•3/6/23, 9:02 AM

i see the problem, you did not followed the ratos instructions

Helge Keck•3/6/23, 9:02 AM

one of the oictopus stepper connectors is a copied conector

Helge Keck•3/6/23, 9:04 AM

Helge Keck•3/6/23, 9:04 AM

zoom into the photo

Helge Keck•3/6/23, 9:04 AM

just dont use connector # 4

Helge Keck•3/6/23, 9:04 AM

its a copied signal from connector # 3

genius23plOP•3/6/23, 9:06 AM

now im see

Helge Keck•3/6/23, 9:07 AM

nexxt time if you ask such questions itt would be good to tell the people you are not using RatOS

Helge Keck•3/6/23, 9:07 AM

i highly recommend to connect everything as described in the ratos doku

Helge Keck•3/6/23, 9:08 AM

and to use ratos ultimately

Helge Keck•3/6/23, 9:08 AM

it makes your life so much easier

HHelge Keck nexxt time if you ask such questions itt would be good to tell the people you ar...

genius23plOP•3/6/23, 9:12 AM

OK, will check this, and thank you for support

genius23plOP•3/6/23, 9:31 AM

its works , thank you very much

Z_TILT_ADJUST - Impossible to complete.

Similar Threads

Similar Threads

Similar Threads