The damping compensation is essentially negative damping, so you can find a value that's on threshol

The damping compensation is essentially negative damping, so you can find a value that's on threshold of stability. A nudge test is a good indication. If you nudge it and it starts to accelerate it means the value is too big.

Reed•3/20/23, 3:08 PM

That’s amazing.

Wwalmis The damping compensation is essentially negative damping, so you can find a valu...

Will3D•3/20/23, 6:10 PM

OK, thank you.

MMagpie That's how I started. This is how that board somehow has ended up

RustBelt•3/20/23, 10:32 PM

It’s a dangerously slippery slope for the poor wallet.

MarshmallowBBQ•3/21/23, 5:17 PM

What is the approximate shipping cost to Indianapolis US for motors kit?

MMarshmallowBBQ What is the approximate shipping cost to Indianapolis US for motors kit?

walmisOP•3/21/23, 5:24 PM

It's roughly 50EUR using FEDEX for the smaller motors kit

skyPickle•3/21/23, 9:07 PM

dont forget you'lll also get a bill from fedex for $35 for import tariff

SskyPickle dont forget you'lll also get a bill from fedex for $35 for import tariff

TheAmazinGreat•3/21/23, 9:16 PM

Kits might be less than the tariff threshold.

Ye Old Grog•3/21/23, 10:02 PM

I didn't get hit with a tariff for my motor kit

FlatSpin•3/21/23, 10:04 PM

$800 above gets hit into the US.

ddrake1984•3/21/23, 10:37 PM

anything over $1000 in Australia gets hit with Import tax

ddrake1984•3/22/23, 9:01 AM

does anyone have the WinWing F18 grip? for some reason my right hat switch does not work (up/down/left/right), but the push does work

walmisOP•3/22/23, 9:04 AM

It's mapped to a hat as I recall

walmisOP•3/22/23, 9:05 AM

@mike_aka_mugs has this grip

Wwalmis It's mapped to a hat as I recall

ddrake1984•3/22/23, 9:10 AM

ah, apologies, it works in DCS, didn't show up to be working in the vpforce program

ddrake1984•3/22/23, 9:10 AM

the button it's assigned to is 45,46,47,48

amadeus•3/23/23, 1:21 AM

Question: when updating firmware, will existing settings be wiped out? Just want to check if I should screenshot them before updootin

Aamadeus Question: when updating firmware, will existing settings be wiped out? Just want...

walmisOP•3/23/23, 5:46 AM

Nope, it should migrate automatically. But you can always export them to a file as a backup.

PiNKSH!T•3/23/23, 6:26 AM

Ummm bugger, I seem to have lost all my config's. I just did the firmware update & downloaded the newest config app, when I moved my config folder I made to the new app to tidy things up I launched the config app & when I try to import my configs they're gone?

PiNKSH!T•3/23/23, 6:30 AM

I found them

PiNKSH!T•3/23/23, 6:30 AM

amadeus•3/23/23, 6:53 AM

so one question i have -- it would be nice to be able to manually define the center position raw value -- i'm finding that with calibration and tweaks -- it's basically impossible for me to get my Y axis to have 2048 as my center without severely limiting the throw (or I am perhaps doing something wrong?)

amadeus•3/23/23, 6:54 AM

after a calibration and some manual tweaks of the end points -- i have around these settings (was able to tweak X to have 2048 exactly tho