is there a short write up of how to add effects and options available in Telem script?
is there a short write up of how to add effects and options available in Telem script?
FYeah, you need an FFB collective 
MNot sure what printer you have, but outside a scant few most need tuning in all axes before they print dimensionally accurate. I had to make pretty big changes before mine would reliably print to dimension. Start by calibrating the extruder axis, then extrusion width, then x/y/z. I used Pronterface to read/write settings to my printer's firmware, following this guide: https://all3dp.com/2/how-to-calibrate-a-3d-printer-simply-explained/
All3DP
Check out our 3D printer calibration guide to learn how to calibrate your 3D printer and fine-tune your slicer settings!
WFor these prints I used a Flashforge creator 3, mainly as I can print 2 pulleys simultaneously. It's previously shown to be dimensionally accurate, however I admit I don't think I've ever run a calibration cube on it. Being a closed system I can't use Pronterface. But it should be better than most i3 style clones out the box.
PCan you order kits and what do they come with?
Pif they exist
MRhino kits? Yes they exist, the wait is short and it's the 2 motors (with the drives already sorted) and the mainboard everything plugs into that plugs into the computer.
https://discord.com/channels/965234441511383080/986474224241741884/986485131906809866
https://discord.com/channels/965234441511383080/986474224241741884/986485131906809866
PAre files available to laser cut our own parts?
AI don't believe so. Okona is working on a full DIY kit to go with the VPForce motor kits, but if I am not mistaken he is going to produce and sell them.
A
A@will3d good guide for 3D printer tuning https://ellis3dp.com/Print-Tuning-Guide/
This is actually for the VORON printers but can also be applied to most others.
This is actually for the VORON printers but can also be applied to most others.
TThe GitHub that AsBurli linked for mabo1972 and a few other options you might find are built for the 57BLF size motor kits. If you buy the bigger motors (86BLF) you will need to modify the files or design your own.
GI would like to know that too. By copying the weapon_release effect I added a very simple feedback for the flaps on all Jet Aircrafts using the aircrafts.py file (not realistic at all :D). But when I tried to add Landing gear transition and airbreak (which I believe are their status values - noted in Purple on the picture) I was unable to do. I am too dumb to understand any of this and I just "monkey see monkey do" with the already added effect. Maybe someone more clever can use the Runway_Rumble or the Buffeting telemetry as a model to help us implement the others.
PAh, ok, I downloaded the executable release (which works fine), should've gone for the script version, I guess?
PI'm going to try sink my teeth into it on Sunday, hopefully. Should it skip my mind, ping me and I'll share my findings. 
GAwesome, good luck. There are soo many opportunities with added effects :).
Pthank you
WThanks, I'll take a look. I did complete my calibration cubes. They turned out a little over sized. X - 20.1 Y - 20.08 Z isn't really an issue in this situation.
WSo perhaps that .5-1% is what is causing the issue. Whilst I don't think I can tune that out in the printer, I can simply scale accordingly. Might be worth a shot.
TCan you modify the steps/mm through the printers user interface? Is there a settings/advanced settings menu option? Most firmwares I have seen allow this so you don’t have to connect to a PC
MThere are a few out there, including the one walmis modified to make the stock Rhino from on github. There are a few iterations of Propeller's floating around but I don't have links off-hand.
As @.aniron mentioned I am developing a kit to accompany walmis's motor kits. My focus on 1. kinematics 2. form factor and 3. mounting options, and got the shell down to a 150mm cube that can be bottom/top/front or back mounted. I've been posting progress on in the showcase channel https://discord.com/channels/965234441511383080/972180323787997255/1087148842589360128
As @.aniron mentioned I am developing a kit to accompany walmis's motor kits. My focus on 1. kinematics 2. form factor and 3. mounting options, and got the shell down to a 150mm cube that can be bottom/top/front or back mounted. I've been posting progress on in the showcase channel https://discord.com/channels/965234441511383080/972180323787997255/1087148842589360128
Pthank you for the resources
MAnother one to look into is LaserWing
WI don't believe that is an option on the Flashforge UI.
RYou’ll probably have to go into G-code to do it. I had to with my little Monoprice Mini. Either direct USB injection or a lump of G-Code on an SD card to run.
W!status
VHey @warwolf09,
So the last Shipped RHINO is #0070 on 2023-03-29
Average waiting time from preorder to shipped is 147 days, median is 182 days, max is 214 days
70 Rhinos are shipped in total
So the last Shipped RHINO is #0070 on 2023-03-29
Average waiting time from preorder to shipped is 147 days, median is 182 days, max is 214 days
70 Rhinos are shipped in total
WFlashforge use proprietary code. So can’t do that.
IDoes the a4 have any ffb capabilities?
Jif it did it would be the best community mod ever (not that it wasnt already but you know what i mean)
RGitHub
Gcode to x3g conversion post processor. Contribute to markwal/GPX development by creating an account on GitHub.
RIt’s not quite Proprietary, just a binary condensation of G-code.
IJust curious. I’m #76 so waiting patiently I should have my hands on one to try soon
Jyeah ive no clue if it does or not, would be amazing if so
IAlso I’m sure I will figure it out soon enough. But do different airframes have different base setting profiles? How does that work…
Ji assume itd b based on what devs put
Jif ur talking dcs modules at least
IYeah
Jim #98 so not too far behind
II’ll download the software but been out of town for a couple weeks and will continue to be for another week or so. So was just curious while I’m on the road and can’t do anything anyway
INice just paid for mine with 6 to go it looks like. Hopefully it won’t take long. But no rush.
Jas i understand it best dcs modules are f14 and mirage f1
Jin regards to dev implemented ffb
II’m most excited for the f14, warbirds and helicopters.
IAnd the easy switch between them. I hope… ha
Jonce i have mine ill begin adding flight sim gear to my new racing rig
Jgonna try center mounting the rhino
INice. I currently have a cm3 with long extention on a center desk mount. I’ll probably have to use a shorter extension or not one at all with the vp I’m guessing.
Jits basically as tall as a virpil stick
MUnless I'm missing something that is about the gcode it uses to slice/print from, x3g. The gcode you adjust for pid tuning is in the printer's firmware, which I gather is some variant of Sailfish on Flashforge machines. That's where the adjustments to steps/mm are made, not the slicer. Can a Flashforge printer hook up to a computer via USB? If so can't one just use Pronterface or Octoprint to access Sailfish to tweak pid like any other printer's firmware?
IThe vp base?