TGood info to know!
WAdded a 330ohm resistor on the data line from the shift register, solves the problem with a long wire 
WWill add it on the next revision of the board
Si have a resistor variety pack i'll give that a try here too.
Swould it be better on the SR side or usb board side
Won SR side
SIT WORKS! 
SHey i have a buddy that's pretty good with repairing phones and other tiny electronics and i happen to be seeing him tomorrow. Is there a spot on the board that you would think to look at first for that one i killed?
WProbably the voltage regulator would be my first suspect, but the mcu might be damaged though.
PHey Walmis I'm getting some funny effects in IL2 with the A-20, I think it might be related to inertia? The stick in game is sort of jumping along the axis, especially when I trim to full nose down, when I move the stick it jumps back to middle of Y axis. When I try to log the data it stops when I alt tab back? is there anyway to log the data & save the log file?
WNot sure what to make of this, too little information. Need something more to go on.
The data log button should stay activated irrespective from alt-tab status. Data is logged to samples.csv file inside the configurator folder.
Is it possible you have bound two different controllers for the main axis and they conflict?
The data log button should stay activated irrespective from alt-tab status. Data is logged to samples.csv file inside the configurator folder.
Is it possible you have bound two different controllers for the main axis and they conflict?
Psamples.csv8.69MB
Pgetting late for me atm, I'll jump on IL2 tomorrow & try to capture it better for you.
WYeah, I see some oscillations
Wcan you show me your settings?
P
Wand effects tab too 
P
P
WYeah, turn off breakout force
Wthat one is a bit broken with trim
Pahh ok cool, I just use it like a deadzone in the centre
Wand oscillations are probably because of untuned friction settings
Wcan you also expand the
Advanced sectionsP
P
Wset spring to 8Hz, damper to 4Hz, Friction and inertia to 6Hz should perform better
Pshould I set it like that for all my profiles?
Pthis one is just general for warbirds
Wyeah would be best for all
Pcheers m8
HI’m looking at a Rhino FFB Board Rev 1.2 for a friend of mine. Looks like he may have killed the 3v3 reg. Is there any documentation for this board that I can look at?
SThanks Whitey 
HA schematic?
HBoardview?
HEven just a BOM would help a little
TSo are you saying that these should be the new default settings?
WHey, the LDO is this one here, it's XC6206 but any other SOT23-3 should work fine:
WYeah, I've updated the defaults, there's a file included in the configurator directory in
configs/rhino-defaults.vpfconfThank you. I don’t believe I have any 3 pin ones on hand (Just some MIC5219-3.3) so I’ll have to order one or 2
P@walmis Hey m8, I'm getting a clunk again when moving along the x axis, the gear is tight, so are the grub screws. Any idea what could be causing this?
Pwhen I move it right & it makes the clunk feeling, after that the physical stick is sitting to right but the software says it's centered
WHey, if you can't make a clunk with your hand while holding the large gear it's probably still the small pulley that's slipping.
Pthe small gear with the two grub screws? both of those are tight, should I look at pulling that gear off & see if the shaft has been dented by the grub screws slipping?
WYeah, you can even try to reattach the small gear in a different orientation
Pok I'll try that, what size are those grub screws, just in case I want to replace them?
WThey're M4 3mm length DIN 916
WBefore you start doing stuff, can you record some data with that clunk happening?
PSorry I missed htis, hang on
Pone of the grub screws won't come out