Ok I was able to determine I will want a 200mm extension. So I think I will get a 50% limiter. I'll

Ok I was able to determine I will want a 200mm extension. So I think I will get a 50% limiter. I'll also get a 75% limiter should I want to change to 100mm.

VVulcan Best to get a protractor out, put it where the base goes and eyeball the obstruc...

ddrake1984•5/4/23, 1:17 PM

that's exactly how I have mine mounted

ddrake1984•5/4/23, 1:17 PM

JJon (Bounty_V)Ok I was able to determine I will want a 200mm extension. So I think I will get ...

Vulcan•5/4/23, 1:28 PM

That sounds like a good starting point, if the throw isn't enough for your personal preference with the 50% try the 75% and if that's too much get another one later somewhere in the middle

zbyte•5/4/23, 5:19 PM

Apologies for my ignorance but trying to understand the subject, the throw limiter will restrict the arc length movement of the stick to avoid hitting other objects during usage, the standard angle per axis (angular displacement) without limiter is 44 degrees give or take, with a 200mm extension (close to radius value since some distance from pivot is not accounted by the extension), you limit this 44 to 22 degrees give or take and with a 100mm extension you could "assume" roughly 33 degrees. The Rhino then will be calibrated to whichever max allowed throw is at its max value and will operate accordingly. Questions, is my statement accurate? Is the Rhino adjustment linear or follows other function like logarithmic or exponential or else? Thank you.

amadeus•5/4/23, 5:52 PM

When you calibrate the rhino you basically tell the firmware it the minimum and maximum distance of physical travel for each axis, so then it maps that to what it reports to windows/games as -100% to 100%, (technically it’s reported as an integer value, like -4986 to 4986 I think?) but yeah linear travel along those value ranges, no curves are anything are added if you limit the throw

PiNKSH!T•5/5/23, 6:05 AM

@walmis Hey m8, I've got replacement grub screws but one of the ones in the gear won't come out, their way too shallow. I'm going to try & superglue the alan key to the top of the grub screw, if that doesn't work what am I supposed to do?

PPiNKSH!T @walmis Hey m8, I've got replacement grub screws but one of the ones in the gear...

walmis•5/5/23, 6:09 AM

I usually use a hex screwdriver so I can get a good pressure on the screw to get it out, the L shaped allen key might be difficult to use

walmis•5/5/23, 6:10 AM

a dab of wd40 might help also

walmis•5/5/23, 6:11 AM

also you might try tightening the other one with a new grub screw, might be enough

Wwalmis also you might try tightening the other one with a new grub screw, might be enou...

PiNKSH!T•5/5/23, 6:33 AM

Yeah I'll try this, cheers m8

Wwalmis also you might try tightening the other one with a new grub screw, might be enou...

PiNKSH!T•5/5/23, 6:42 AM

ok that's fixed it, but I'm keen to get the other one out, in fact I'm going to replace the ones on the other motor too

Aamadeus When you calibrate the rhino you basically tell the firmware it the minimum and ...

zbyte•5/5/23, 10:57 AM

Thanks

JJon (Bounty_V)Rhino owners! Looking to get 1 or more throw limiters with my Rhino, and I'm a c...

LeLv30_Superbus•5/5/23, 12:06 PM

With a 200 mm extension and no hole in my seat 18° back and 12° forward works for me. Many fighters have more throw backward than forward. I can reach my front panel switches and knobs without any trouble and the stick is not hitting anything. This is important b/c I only fly in VR. Remember to limit sideways movement too. I'm hitting my own feet at ½ throw when there's zero pitch so maybe try that value. Edit: my Rhino is mounted at 98 mm height (it's on two pieces of 2x4 sideways) and I'm sitting at 460 mm. Grip is MCGU.
Pictures: 📃general

Jon (Bounty_V)OP•5/5/23, 12:07 PM

I requested 50% on both x and y axis, and a 75% on both x and y axis. If I need further adjustments I can probably source them myself

JJon (Bounty_V)Ok I was able to determine I will want a 200mm extension. So I think I will get ...

JakeSixx33 | 744 |•5/5/23, 1:42 PM

Walmis created a limiter for me that comes very close to limiting the travel of the F-18C specs for 2.5" forward and 5" rearward. I also use a 200mm extension. The calibration software works wonders and gives full control input with the reduced physical input distance from center. Thanks @walmis

JakeSixx33 | 744 |•5/5/23, 1:43 PM

JJakeSixx33 | 744 |Click to see attachment

ddrake1984•5/6/23, 12:13 AM

well.. it's about 150mm from the pivot to the base of the grip

Dddrake1984 well.. it's about 150mm from the pivot to the base of the grip

JakeSixx33 | 744 |•5/6/23, 12:14 AM

Keeps the stick from striking MFDs mounted in the front.

ddrake1984•5/6/23, 12:15 AM

the limiters should be doing this yes

NNumber481 Well, I cut the connectors out and direct soldered the cable.. ~~problem is (mo...

PiNKSH!T•5/6/23, 2:46 AM

hey guys I'm not very good when it comes to electricity/electronics but would an extra layer of shielding help? Like another layer of heat wrap? With electricity not really going through the wires I'm guessing that's what causes the 'noise' when the wires are bunched up & not when they're out straight? Then would the extra layer of heat wrap help or not really? More curious than anything now

PPiNKSH!T hey guys I'm not very good when it comes to electricity/electronics but would an...

Number481•5/6/23, 2:57 AM

IDK. Perhaps if the cable was shielded, it wouldn't have been a problem in the first place.. but I can't think of anything you could do to the cable externally that might help, and still be able to get it all back in the tube. The cable on these extensions is obscenely long. I ended up taking about 12cm out of the top half of the cable and soldered it back together.. working perfectly now.

NNumber481 IDK. Perhaps if the cable was shielded, it wouldn't have been a problem in the ...

PiNKSH!T•5/6/23, 3:08 AM

Ahh ok cool, why does it have to be so long? I'm not familiar with Virpil, but does it need some slack for plugging in the grip?

PPiNKSH!T Ahh ok cool, why does it have to be so long? I'm not familiar with Virpil, but d...

Number481•5/6/23, 3:17 AM

You can pull the connector out at the bottom to assist in attaching it to the base. But it only needs maybe 3-5cm of slack for that to work. Like I said, I cut out about 12 cm and could have probably taken a little more.

Number481•5/6/23, 10:33 PM

What’s the proper way to set up for DCS community mod modules that don’t support FFB (Herc) so the stick just acts like a regular joystick? By default the stick is just limp. Are we supposed to enable “sticky” in the spring effects or is there a better way to handle this dynamically?

NNumber481 What’s the proper way to set up for DCS community mod modules that don’t support...

PiNKSH!T•5/7/23, 4:42 AM

The telem app should give basic ffb effects to aircraft

PiNKSH!T•5/7/23, 4:42 AM

you may need to add it to the telem app config file, might need someone else to help with that though sry

PiNKSH!T•5/7/23, 4:43 AM

check through support here you should find convo on it

NNumber481 What’s the proper way to set up for DCS community mod modules that don’t support...

walmis•5/7/23, 5:02 AM

TelemFFB def has the framework for this, with a few lines it will be possible to add a spring and other effects for non FFB aircraft. However until this is done you can use the "sticky" feature.

Wwalmis TelemFFB def has the framework for this, with a few lines it will be possible to...

JakeSixx33 | 744 |•5/8/23, 2:16 PM

Telem is what makes modules come alive. Is it possible to get a list of the commands available with notes for implementation? I realize it is still WIP and will grow over time.

Phantom•5/9/23, 1:34 AM

@walmis Do I need to order anything extra like a limiter so my stick will behave like the F/A 18 specs ?? I seem to recall something about a limiter in the order form ?

PPhantom @walmis Do I need to order anything extra like a limiter so my stick will behave...

PiNKSH!T•5/9/23, 4:24 AM

Yeah m8, you can order limiter plates when you place your order, you can also buy these anytime. The Rhino software does have a endstop feature that you can change per config, but the physical endtop plates are obviously going to be a bit more solid. I believe you can also get the 3d files to print them yourself

Troll 🇸🇪 🇳🇴•5/9/23, 5:10 AM

The limiter is in the knowledge-base.
You can change the dimensions to your liking and print it.

https://discord.com/channels/965234441511383080/1092338475795238962

ddrake1984•5/9/23, 6:22 AM

For me one of the reasons to go FFB is so you can configure endstops on the fly so to speak, without having to assemble/dissasemble.
However physical plates are more solid, but I would still want something that could attach/detach quickly rather than screwing and unscrewing when I want to change the range

Phantom•5/9/23, 10:36 AM

Perfect, thanks.

PPhantom @walmis Do I need to order anything extra like a limiter so my stick will behave...

JakeSixx33 | 744 |•5/9/23, 1:46 PM

He made one for me that is very close. Limits forward and rearward travel. The software calibrates to the physical limit so you lose no input authority.

Havebug•5/9/23, 3:00 PM

gents, I'd like to assign two buttons of my throttle for the Y axis trim,

Havebug•5/9/23, 3:00 PM

Havebug•5/9/23, 3:01 PM

do you know what is the right procedure? When I run the loopback the main windows does not catch the buttons...

HHavebug do you know what is the right procedure? When I run the loopback the main window...

LeLv30_Superbus•5/9/23, 3:29 PM

Isn't Virpil is natively supported? Should work without loopback.

LeLv30_Superbus•5/9/23, 3:29 PM

Wait this is the THROTTLE

AndyHill•5/9/23, 3:30 PM

one way to get ffb throttle

LeLv30_Superbus•5/9/23, 3:30 PM

Try selecting Loopback here then try the buttons

AndyHill•5/9/23, 3:30 PM

anyway it shouldn't matter what you use for the loopback, it should still work

Havebug•5/9/23, 3:39 PM

Thank you very much!

Jon (Bounty_V)OP•5/9/23, 3:45 PM

https://www.reddit.com/r/hoggit/comments/nc3684/my_tool_to_programmatically_control_virpil_leds/ Since I hadn't seen this mentioned before figured I'd share as I'm curious - would this let Rhino Virpil users control the LEDs? Or since it is github be modified in such a way so as to do so? Food for thought THINKING

r/hoggit - My tool to programmatically control Virpil LEDs is now up!

54 votes and 42 comments so far on Reddit

JJon (Bounty_V)https://www.reddit.com/r/hoggit/comments/nc3684/my_tool_to_programmatically_cont...

walmis•5/9/23, 4:35 PM

Unlikely, this library controls LEDs through high level HID commands available with the base itself. What is unknown to me yet is the protocol used on the physical/electrical layer between the base and grip. One way to figure this out would be to grab a Virpil base and capture some traces with a logic analyzer. I'll grab a base eventually like I did with the WinWing, though the WW grip adapter had higher priority and LED control would be a nice-to-have

Jon (Bounty_V)OP•5/9/23, 4:36 PM

Yeah for sure makes sense. Definitely an interesting topic, and the way it works could potentially open up some possibilities in the future

Sundown•5/9/23, 8:23 PM

Just got my unit and it's impressive. However, I do hear creaking when moving the stick around, with it being more prominent under higher spring forces. It can also be heard when the unit is off, almost like a bit of sticktion and happens more with the X-axis. It's not the boot (which makes its own expected noise) and seems to be coming from the unit itself. Has anyone else encountered this?

Number481•5/9/23, 9:09 PM

I do get some creaking on mine. Best o can tell is it comes from the joint between the extension and the base and not anything internal. Perhaps where the plastic threaded piece of the base joins to the aluminum tube that comes up from the gimbal.

I can hold the gimbal in place with one hand and “tweak” the extension/grip left/right and produce the same creaking.

Number481•5/9/23, 9:09 PM

Ok I was able to determine I will want a 200mm extension. So I think I will get a 50% limiter. I'll

Similar Threads