Might be interesting trying to figure out how to mount it.
Might be interesting trying to figure out how to mount it.
RKinda like this
JIf you click to the support channel message I linked they are mounting it directly using the bottom of the rhino, and not the monstertech mount
Joh you mean a 8020 piece at a 90 degree angle
DI will take a further look. I am so far down on the order order that I have plenty of time.
J
Jjust another method to fasten, but this would be 'hidden'
JObviously not as rigid as external bolting methods
RCurrently how it’s connected with virpil. The rhino needs to sit flush on the floor and connect to cross beam I’ll cut and place on the floor attached to bottom
JThe more I dig the deeper I go down a rabbit hole of things not actual 8020 profiling to allow for right angles
JLooking at the pic the Rhino will definitely be a little taller
J(oh flush on a different part I'm silly 
)
)RUsing the monster tech mount to the point of contact is on the front of rhino
JI'm sure you've seen already, but showing again for posterity for anyone else who sees convo in the future
They use a special kind of 8020 fastener which requires a special cut of 8020 to fasten at a 90 degree angle, which is then used for the monster tech mount to affix to the cockpit
They use a special kind of 8020 fastener which requires a special cut of 8020 to fasten at a 90 degree angle, which is then used for the monster tech mount to affix to the cockpit
Jpic from below
JWould something like that work perhaps? You could even have the vertical part mount underneath the floor part you have on top of the frame on the other side of where you have the cyclic currently, then you could have extra room with which to make the rhino flush with the cockpit
RI think so
RMy extruded aluminum is actually 4040.
NHi, pretty new on Discord. I would be interested in ordering this and I can't DM the admin of the server. Thanks for any help 
PI have two, both have been converted to have the CH Fighterstick Pro Grip/handle on them, one being a shaft extension version as well, no idea, I guess I will sell one of them, and keep one as a backup, the one pictured retains the twist rudder whilst the other version with the extended handle does not.
J#
faq <---click on this it takes you to all information about it and how/where to order etc.
faq <---click on this it takes you to all information about it and how/where to order etc.NThank you
CI might convert it (the old MSFFB2) to 3D printed grip like a B8 or Spitfire or KG12. I was wondering if I could convert it to pulleys/gears for my rudder. That’d be pretty cool
S@_gunzablazin love your buddyfox ufc! I miss mine 
S@CapnFlint I added the B8 grip from an old TM topgun stick, and a 500mm carbon fiber rod, since I added extra resistors. Would be a nice gift for someone as an intro to ffb!
DI love the BuddyFox UFC!
DHey guys, just wondering if this kit can be used for something like a seat mover? In other words could you pull motion data from a sim and drive Surge, Sway and Yaw in a seat?
Adepends on the sim, but kind of yes
J#faq #
knowledge-base has the info you need. I think there is an open source thing on github that could be used to interface with that in such a capacity but it might require some additional code writing on your part
faq #knowledge-base has the info you need. I think there is an open source thing on github that could be used to interface with that in such a capacity but it might require some additional code writing on your partAI don't know if it's the optimal solution, though
JWe're very early days software wise for Rhino related stuff. For example current iteration does not have rudder pedals yet afaik (referring to an answer from walmis in #
support a day or 2 ago)
support a day or 2 ago)
LTested it out in the ASK-21 & 23, and yeah, in the slip the rudder stays in it "pushed" position
PSadly mine has had a small fault ever since new - #3 doesn't register every time unless you press it in a particular way, which I suppose you learn to do after a while of ownership
KI have a feeling that this is one of those things that you have to be looking for to find out. At least when I'm in a slip trying to hit my aiming point, the particular feel of the rudder pedals is not high on my list of things to think about. Appreciate you flying and finding the answer. I'll be back in the 2-33 in a couple weeks and will take careful note as well.
KThis is my first attempt at a variation on the shaft winding photos posted. I need to find a better way to secure the slippery, synthetic, zero stretch fishing line or move to the steel braided cable I also have. Overall the mechanism seems to work as expected though. 13:1 gear ratio. No backlash. No need for an exact timing belt. Just a prototype but I’m pleased so far.
V:package: 
RHINO #0099 Has Shipped!
RHINO #0099 Has Shipped!V:package: 
RHINO #0100 Has Shipped!
RHINO #0100 Has Shipped!
D100!!! celebrations!!
JNice
HCongrats!
JWalmis does vpforce have an Instagram? Was wanting to tag it when I share my unboxing pics
BHi VPforceBot, I filled out your VPforce RHINO Preorder and emailed it to you.
JYou just fill out the Google form in the faq. You can then dm the bot a command for updates on where you are at in the queue, and it will also dm you when it's time to pay etc.
The command is !info [your email from the form]
Without the [ ]
The command is !info [your email from the form]
Without the [ ]
BThis is my Current VPC Cyclic
BIn filling out the form, Discord handle
In the form name#1234. This will allow status updates via discord (in development)
B9#9487
Wrong user pattern
In the form name#1234. This will allow status updates via discord (in development)
B9#9487
Wrong user pattern
BAm I doing something wrong?
BDoes your form only work with GMAIL?
BDid you receive my order form?
JYou would receive an e-mail confirmation.
It is all automated.
It is all automated.
JIt just wants your discord name. B9#9487 is your current discord name.
B