Save config error when setting position endstop offset

I am using the ratos voron 2.4 config. When setting end stop offset with both the z end stop and a klicky probe, I get the following error : SAVE_CONFIG section 'stepper_z' option 'position_endstop' conflicts with included value.

printer.cfg17KB

miklschmidt•5/20/23, 5:42 PM

I'm not sure what you're trying to do here exactly. You can't both use a probe and an endstop for homing Z. Its either or.

miklschmidt•5/20/23, 5:42 PM

If you use an endstop, you need to adjust position_endstop to where your nozzle touches the bed.

miklschmidt•5/20/23, 5:47 PM

miklschmidt•5/20/23, 5:50 PM

That is done via Z_ENDSTOP_CALIBRATE btw.

miklschmidt•5/20/23, 5:50 PM

Also you should adjust

variable_safe_home_x: "middle"
# Possible Values: 'middle' or an absolute y coordinate
variable_safe_home_y: "middle"

variable_safe_home_x: "middle"
# Possible Values: 'middle' or an absolute y coordinate
variable_safe_home_y: "middle"

to be the coordinates of your endstop switch

brilliant-limeOP•5/20/23, 5:51 PM

I think this might be a fundamental misunderstanding on my part. I was under the impression that the z endstop was for nozzle offset and probe would be for qpl + meshing.

miklschmidt•5/20/23, 5:52 PM

Yeah you can do that, but you'd need to calibrate your offset with Z_ENDSTOP_CALIBRATE

miklschmidt•5/20/23, 5:53 PM

I'm not sure if PROBE_CALIBRATE works while using a z_endstop. That's a klipper thing, not a RatOS thing.

brilliant-limeOP•5/20/23, 5:53 PM

I end up getting this. Not really sure what to do with it

SSpotigus I end up getting this. Not really sure what to do with it

miklschmidt•5/20/23, 5:53 PM

When running Z_ENDSTOP_CALIBRATE ?

brilliant-limeOP•5/20/23, 5:54 PM

yes

miklschmidt•5/20/23, 5:54 PM

You're supposed to use the the buttons to go to Z=0 (ie, where the nozzle touches the bed)

miklschmidt•5/20/23, 5:54 PM

paper test

brilliant-limeOP•5/20/23, 5:54 PM

I end up getting Manual probe failed! Use TESTZ commands to position the
nozzle prior to running ACCEPT.

SSpotigus I end up getting Manual probe failed! Use TESTZ commands to position the nozzle ...

miklschmidt•5/20/23, 5:55 PM

Did you click the buttons before hitting accept?

miklschmidt•5/20/23, 5:56 PM

You're supposed to do a paper test, and click the buttons until the nozzle touches the paper and theres a minimum of friction when you pull on the paper

brilliant-limeOP•5/20/23, 5:56 PM

Igore that

brilliant-limeOP•5/20/23, 5:57 PM

SAVE_CONFIG section 'stepper_z' option 'position_endstop' conflicts with included value

miklschmidt•5/20/23, 5:58 PM

i don't know what the problem is.
You can subtract the value manually from position_endstop of line 353

miklschmidt•5/20/23, 5:58 PM

@heisenberg19x can you help here?

miklschmidt•5/20/23, 6:00 PM

@heisenberg19x i'm assuming you can't have

[stepper_z]
position_endstop: -0.10

[stepper_z]
position_endstop: -0.10

in an included file, for some reason. It's stupid as it'll just override it.

miklschmidt•5/20/23, 6:01 PM

@.spotigus Instead of the z-endstop include on line 131, replace it with this:

[stepper_z]
endstop_pin: z_endstop_pin
position_min: -1.5
homing_speed: 10
second_homing_speed: 3.0
homing_retract_dist: 3.0

[stepper_z]
endstop_pin: z_endstop_pin
position_min: -1.5
homing_speed: 10
second_homing_speed: 3.0
homing_retract_dist: 3.0

And try again.

sacred-rose•5/20/23, 6:03 PM

the endstop includes where changes with RatOS 2 merge iirc, I just use the Probe as Z Endstop like a RR

brilliant-limeOP•5/20/23, 6:05 PM

gotcha, no auto z offset then?

brilliant-limeOP•5/20/23, 6:11 PM

@miklschmidt I ended up just using probe only.

brilliant-limeOP•5/20/23, 6:11 PM

I want to get the printer working. Im gonna revisit it later.

HHeisenberg@Krähendruck 🤷 the endstop includes where changes with RatOS 2 merge iirc, I just use the Pr...

miklschmidt•5/20/23, 6:13 PM

Not the z one

HHeisenberg@Krähendruck 🤷 the endstop includes where changes with RatOS 2 merge iirc, I just use the Pr...

miklschmidt•5/20/23, 6:13 PM

~~Can't use the probe for Z when its a clicky, z has to be homed before it can be picked up on a V2.4~~

SSpotigus @miklschmidt I ended up just using probe only.

miklschmidt•5/20/23, 6:14 PM

How?

miklschmidt•5/20/23, 6:14 PM

Oh wait is the klicky dock attached to the gantry?

Cclean-aquamarine ~~Can't use the probe for Z when its a clicky, z has to be homed before it can b...

sacred-rose•5/20/23, 6:14 PM

I have it with Klicky running like that

Cclean-aquamarine Oh wait is the klicky dock attached to the gantry?

sacred-rose•5/20/23, 6:14 PM

Yes

HHeisenberg@Krähendruck Yes

miklschmidt•5/20/23, 6:14 PM

aaaah

miklschmidt•5/20/23, 6:15 PM

Yeah then the z endstop is only useful for nozzle offset calibration

miklschmidt•5/20/23, 6:15 PM

which would only be when you change nozzle or bed surface

brilliant-limeOP•5/20/23, 6:16 PM

Exactly, i have on occasion forgot to do that after changing a nozzle.

miklschmidt•5/20/23, 6:16 PM

You should be able to get it working if you replace the z-endstop include.

miklschmidt•5/20/23, 6:16 PM

@heisenberg19x we can remove the position_endstop from that include and put it in the template, then it should be fine.

sacred-rose•5/20/23, 6:17 PM

brilliant-limeOP•5/20/23, 7:00 PM

Let me know if you need me to test anything.

Save config error when setting position endstop offset

Similar Threads

Similar Threads

Similar Threads