so, I need to unbind it a leave it unbind right?
so, I need to unbind it a leave it unbind right?
Nyeah.. in order to get around the way MSFS behaves.... TelemFFB has to be the source of the axis position for the trim following feature to work.
Sso I think I did all things right, and I have all set to true and unbinded the axis and im getting them to move in the sim
Sbut I put power to the ap and watch the yoke move in the sim but I dont see it in the rhino
Ntelemffb log please
Sps im testing in the ground
SSbut the yoke moves it should move in the rhino too
Schanging the hdg bug I can see in the msfs the yoke move and in the TelemFFB I see the ailerondefl move but not physicaly in the rhino
Nremember that MSFS has zero FFB implementation.. so all of the FFB is done through TelemFFB. This trim/AP following was not super simple to implement and is relatively new and while I promise it does in fact work, I certainly havent figured out all of the ways it can be mis-configured yet.. thats why I'm asking the stupid obvious questions.
NSo in general flight, you are feeling the dynamic stick forces? Stick is limp on the ground and stiffens up as you accelerate? What about trim. If you adjust trim, do you see the elevator and/or aileron axis move in the sim and or the rhino move?
SI have to check later but yes i supose I have to test the trim because I had the old config
Swell, is working in flight
Sbut now the aileron in flight its weird almost like loose
NWait.. you were trying the autopilot on the ground before?
NIf you want to increase the spring strength of the axes, change these values in the aircraft config...
Syes
Sand i should work because its a so old system that it dont know if its on the air or groun.. it the same
Sbut the rhino dont comply
NThe rhino doesnt comply because it cant comply.. This is a simulation and we do the best we can to emulate real life behavior.
On the ground, your controls are limp. In Rhino speak, that means we have zero spring force applied to the stick.
With no spring force on the stick, we can't move the center point of said spring force to make the joystick follow the virtual control.
Might work if you configure the aircraft as "center sprung".. which will set a minimum spring force that will be applied to the axes, even when the aircraft is idle on the ground...
On the ground, your controls are limp. In Rhino speak, that means we have zero spring force applied to the stick.
With no spring force on the stick, we can't move the center point of said spring force to make the joystick follow the virtual control.
Might work if you configure the aircraft as "center sprung".. which will set a minimum spring force that will be applied to the axes, even when the aircraft is idle on the ground...
Swell... it simulates the weight of the elevator..
Nelevator droop is just a "constant" force. Constant forces are simply "an amount of force in a given direction"....
Sundervolt error.
Well, I was gettting away with an old 12v 5a laptop brick, so I replaced it with a 20v brick. I know someone mentioned the psu I list was weak...they were right.
Instructions updated
Well, I was gettting away with an old 12v 5a laptop brick, so I replaced it with a 20v brick. I know someone mentioned the psu I list was weak...they were right.
Instructions updated
SThanks
AAh dang it lol I’ll order another one that 5a is suppose to be here tomorrow lol
WYeah, 12Vx5A = 60W which is pretty low compared to included Rhino PSU of 180W
Sthat actually happended to me, with the new telemFFB and the lastest firmware
Sthe long beep and shutdown of one motor
AWhat’s average lead time on a motor set?
JMine shipped out almost immediately.
AIs it possible to adjust the frequency of the vibration effects TelemFFB creates?
AThis should work yeah? SHNITPWR Universal Power Supply DC 24V 12V 5V 6V 9V 14V 19V Adjustable AC/DC Adapter 100V~240V AC to DC Variable Power Converter Multi-Voltage 3.5V ~ 24V 6A 144W Power Adapter 14 Tips LCD Display https://a.co/d/iIdf1Qk
SHNITPWR Universal Power Supply DC 24V 12V 5V 6V 9V 14V 19V Adjustable AC/DC Adapter 100V~240V AC to DC Variable Power Converter Multi-Voltage 3.5V ~ 24V 6A 144W Power Adapter 14 Tips LCD Display
Ndepends on the effect you are talking about. Some are fixed frequency, some are based on real-time telemetry, and some are configurable indirectly by adjusting parameters is the config.
Whttps://www.amazon.com/LRS-350-24-Switching-Supply-350-4W-115Vac/dp/B07RF38JXK this one is a great bang for the buck
350.4W 24V 14.6A Single Output Switchable Power Supply 24 Volts @ 14.6 Amps
SYea the 180w unit I have now is perfect. Thanks again.
I updated docs so no other diy makes the same mistake
I updated docs so no other diy makes the same mistake
HOut of curiosity, could a stronger PSU allow higher motor currents in the rhino without any additional issues?
Aheat is already a thing so at least that would become a limiting factor fairly early on
Sits just me or the x axis is having a big tendency to keep temperature than the y?
SIs it possible that A2A comanche has some FFB implementation that makes some problems with telemFFB? I got a lot of vibration and a long beep and after that the roll comes nimble and the vibration ceases and pitch. it happens more when above terrain over water its gets more smooth.
WThis could be general instability, not necesarily telemFFB. Can you show your VPconf settings?
S
S
SI did nothing but update to the latest telemFFB
Ntry lowering friction (or set it to zero to test).. I still find that any amount of friction will often cause oscillations.
Also, have you modified your spring gain map?
Also, have you modified your spring gain map?
SI did not, because that not so relevant to me.. I was just testing it.
SI'll try the friction and report back
Scan I edit efects in TelemFFB live or I need to reboot the app?
Nmost things you can edit/save the config or the user config live (keeping in mind that userconfig will override primary config)
BI did not know that!
NYessir.... the only things you cant modify on the fly are the system variables (like enabled sims, etc).
Also, you can't add a new aircraft section while live either. That will require a restart (of telemFFB).
Also, you can't add a new aircraft section while live either. That will require a restart (of telemFFB).
Ai would say in general, avoid using friction, use damper instead