undervolt error. Well, I was gettting away with an old 12v 5a laptop brick, so I replaced it with a

undervolt error.
Well, I was gettting away with an old 12v 5a laptop brick, so I replaced it with a 20v brick. I know someone mentioned the psu I list was weak...they were right.
Instructions updated

SubsonicOP•10/28/23, 12:44 AM

Thanks

A. Palmetto•10/28/23, 12:59 AM

Ah dang it lol I’ll order another one that 5a is suppose to be here tomorrow lol

SSubsonic undervolt error. Well, I was gettting away with an old 12v 5a laptop brick, so I...

walmis•10/28/23, 7:02 AM

Yeah, 12Vx5A = 60W which is pretty low compared to included Rhino PSU of 180W

SSubsonic undervolt error. Well, I was gettting away with an old 12v 5a laptop brick, so I...

Snooper•10/28/23, 10:56 AM

that actually happended to me, with the new telemFFB and the lastest firmware

Snooper•10/28/23, 10:56 AM

the long beep and shutdown of one motor

A. Palmetto•10/28/23, 11:45 AM

What’s average lead time on a motor set?

AA. Palmetto What’s average lead time on a motor set?

Jehly•10/28/23, 1:14 PM

Mine shipped out almost immediately.

Antares•10/28/23, 3:28 PM

Is it possible to adjust the frequency of the vibration effects TelemFFB creates?

Wwalmis Yeah, 12Vx5A = 60W which is pretty low compared to included Rhino PSU of 180W

A. Palmetto•10/28/23, 5:24 PM

This should work yeah? SHNITPWR Universal Power Supply DC 24V 12V 5V 6V 9V 14V 19V Adjustable AC/DC Adapter 100V~240V AC to DC Variable Power Converter Multi-Voltage 3.5V ~ 24V 6A 144W Power Adapter 14 Tips LCD Display https://a.co/d/iIdf1Qk

SHNITPWR Universal Power Supply DC 24V 12V 5V 6V 9V 14V 19V Adjusta...

SHNITPWR Universal Power Supply DC 24V 12V 5V 6V 9V 14V 19V Adjustable AC/DC Adapter 100V~240V AC to DC Variable Power Converter Multi-Voltage 3.5V ~ 24V 6A 144W Power Adapter 14 Tips LCD Display

AAntares Is it possible to adjust the frequency of the vibration effects TelemFFB creates...

Number481•10/28/23, 5:27 PM

depends on the effect you are talking about. Some are fixed frequency, some are based on real-time telemetry, and some are configurable indirectly by adjusting parameters is the config.

AA. Palmetto This should work yeah? SHNITPWR Universal Power Supply DC 24V 12V 5V 6V 9V 14V 1...

walmis•10/28/23, 5:28 PM

https://www.amazon.com/LRS-350-24-Switching-Supply-350-4W-115Vac/dp/B07RF38JXK this one is a great bang for the buck

Mean Well LRS-350-24 Switching Power Supply 350.4W 24V 14.6A 115Vac...

350.4W 24V 14.6A Single Output Switchable Power Supply 24 Volts @ 14.6 Amps

Wwalmis Yeah, 12Vx5A = 60W which is pretty low compared to included Rhino PSU of 180W

SubsonicOP•10/28/23, 6:32 PM

Yea the 180w unit I have now is perfect. Thanks again.

I updated docs so no other diy makes the same mistake

Wwalmis Yeah, 12Vx5A = 60W which is pretty low compared to included Rhino PSU of 180W

Hextopia•10/29/23, 12:43 PM

Out of curiosity, could a stronger PSU allow higher motor currents in the rhino without any additional issues?

AndyHill•10/29/23, 1:25 PM

heat is already a thing so at least that would become a limiting factor fairly early on

Snooper•10/29/23, 3:19 PM

its just me or the x axis is having a big tendency to keep temperature than the y?

Snooper•10/29/23, 5:40 PM

Is it possible that A2A comanche has some FFB implementation that makes some problems with telemFFB? I got a lot of vibration and a long beep and after that the roll comes nimble and the vibration ceases and pitch. it happens more when above terrain over water its gets more smooth.

SSnooper Is it possible that A2A comanche has some FFB implementation that makes some pro...

walmis•10/29/23, 5:49 PM

This could be general instability, not necesarily telemFFB. Can you show your VPconf settings?

Snooper•10/29/23, 6:21 PM

Snooper•10/29/23, 6:22 PM

Snooper•10/29/23, 6:23 PM

I did nothing but update to the latest telemFFB

SSnooper Click to see attachment

Number481•10/29/23, 6:24 PM

try lowering friction (or set it to zero to test).. I still find that any amount of friction will often cause oscillations.

Also, have you modified your spring gain map?

Snooper•10/29/23, 6:26 PM

I did not, because that not so relevant to me.. I was just testing it.

Snooper•10/29/23, 6:27 PM

I'll try the friction and report back

Snooper•10/29/23, 6:39 PM

can I edit efects in TelemFFB live or I need to reboot the app?

Number481•10/29/23, 7:19 PM

most things you can edit/save the config or the user config live (keeping in mind that userconfig will override primary config)

NNumber481 most things you can edit/save the config or the user config live (keeping in min...

blave549•10/30/23, 12:07 AM

I did not know that!

Number481•10/30/23, 12:09 AM

Yessir.... the only things you cant modify on the fly are the system variables (like enabled sims, etc).

Also, you can't add a new aircraft section while live either. That will require a restart (of telemFFB).

amadeus•10/30/23, 7:44 AM

i would say in general, avoid using friction, use damper instead

amadeus•10/30/23, 7:44 AM

i.e. jack damper back up to 100%, (probably worth doing the same with inertia as well), and maybe keep friction in the Settings tab at 10% or lower, and also yeet it from the effects tab and instead add some damper to give it that mechanical feeling

Snooper•10/30/23, 10:49 AM

the thing is that I had friction all 100 with no issues prior the last update from TelemFFB

Snooper•10/30/23, 10:51 AM

should I remove Friction in the effects tab too?

Snooper•10/30/23, 11:32 AM

what is this? often it happens and I have to restart TelemFFB.

Snooper•10/30/23, 11:32 AM

Traceback (most recent call last):
File "main.py", line 449, in process_data
File "aircrafts_msfs.py", line 712, in on_telemetry
File "aircrafts_msfs.py", line 680, in on_telemetry
File "aircrafts_msfs.py", line 571, in _update_flight_controls
File "simconnect\sc.py", line 197, in send_event
File "simconnect\datadef.py", line 137, in map_event_id
File "simconnect\sc.py", line 66, in _callable
File "_ctypes/callproc.c", line 993, in GetResult
OSError: [WinError -1073741648] Windows Error 0xc00000b0

During handling of the above exception, another exception occurred:

Traceback (most recent call last):
File "traceback_with_variables\print.py", line 67, in printing_exc
File "traceback_with_variables\print.py", line 98, in wrapper
File "main.py", line 488, in run
File "main.py", line 453, in process_data
File "traceback_with_variables\print.py", line 39, in print_exc
AttributeError: 'NoneType' object has no attribute 'write'

During handling of the above exception, another exception occurred:

Traceback (most recent call last):
File "threading.py", line 1009, in _bootstrap_inner
File "traceback_with_variables\print.py", line 92, in wrapper
File "contextlib.py", line 153, in exit
File "traceback_with_variables\print.py", line 70, in printing_exc
File "traceback_with_variables\print.py", line 39, in print_exc
AttributeError: 'NoneType' object has no attribute 'write'

SSnooper the thing is that I had friction all 100 with no issues prior the last update fr...

Number481•10/30/23, 12:01 PM

If you have friction enabled, and your hand is the only thing moving the stick, the oscillations might not occur. However, s soon as the trim/AP following in latest TelemFFB is moving the stick by itself without your hand on it to stop the oscillations from beginning to amplify.. that can absolutely start the oscillations.

Also... while your friction slider is %100.. you are limiting it to %20 in the effects tab.. important to understand how the two tabs work together.

SSnooper what is this? often it happens and I have to restart TelemFFB.

Number481•10/30/23, 12:08 PM

Can't say for sure. I've not seen that myself nor had any other reports of similar errors...

It looks like an issue with the simconnect code sending the axis position to MSFS.

How is the stability of your USB connection to the Rhino? Does it ever momentarily disconnect/reconnect by itself?

NNumber481 Can't say for sure. I've not seen that myself nor had any other reports of simi...

Snooper•10/30/23, 2:04 PM

no, just happens in the sim

NNumber481 Can't say for sure. I've not seen that myself nor had any other reports of simi...

walmis•10/30/23, 2:27 PM

0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should recover automatically and probably would be a good idea to put the send_eventsend_event into a try .. except .. block

Wwalmis 0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should reco...

Number481•10/30/23, 2:39 PM

easy enough!

Snooper•10/30/23, 2:58 PM

glad to help

Snooper•10/30/23, 4:37 PM

ok, I believe its the engine rumble effect that causing the disconnect of X axis

SSnooper ok, I believe its the engine rumble effect that causing the disconnect of X axis

walmis•10/30/23, 4:41 PM

Can you check the fault code when the axis disconnects? It's in the bottom right in the status bar of the VPConf application

Snooper•10/30/23, 4:42 PM

sdby i'll do it again, I'm in Vr and i doesnt help to this kinds of tests

Snooper•10/30/23, 4:44 PM

Snooper•10/30/23, 4:45 PM

here better than copy the text

Snooper•10/30/23, 4:45 PM

hope not too much serious.. to my end......

Snooper•10/30/23, 4:47 PM

thats why I could recover from it by pressing the red button and then restart it

walmis•10/30/23, 4:50 PM

The safety algorithm is a bit too sensitive, I'll send you a firmware update later

Snooper•10/30/23, 4:55 PM

thanks

Snooper•10/30/23, 4:55 PM

can I reduce the engine tumble too in telemFFB? Look too much

Snooper•10/30/23, 4:56 PM

meanwhile I turn it off

undervolt error. Well, I was gettting away with an old 12v 5a laptop brick, so I replaced it with a

Similar Threads