Is it possible that A2A comanche has some FFB implementation that makes some problems with telemFFB?

Is it possible that A2A comanche has some FFB implementation that makes some problems with telemFFB? I got a lot of vibration and a long beep and after that the roll comes nimble and the vibration ceases and pitch. it happens more when above terrain over water its gets more smooth.

SSnooper Is it possible that A2A comanche has some FFB implementation that makes some pro...

walmis•10/29/23, 5:49 PM

This could be general instability, not necesarily telemFFB. Can you show your VPconf settings?

SnooperOP•10/29/23, 6:21 PM

SnooperOP•10/29/23, 6:22 PM

SnooperOP•10/29/23, 6:23 PM

I did nothing but update to the latest telemFFB

SSnooper Click to see attachment

Number481•10/29/23, 6:24 PM

try lowering friction (or set it to zero to test).. I still find that any amount of friction will often cause oscillations.

Also, have you modified your spring gain map?

SnooperOP•10/29/23, 6:26 PM

I did not, because that not so relevant to me.. I was just testing it.

SnooperOP•10/29/23, 6:27 PM

I'll try the friction and report back

SnooperOP•10/29/23, 6:39 PM

can I edit efects in TelemFFB live or I need to reboot the app?

Number481•10/29/23, 7:19 PM

most things you can edit/save the config or the user config live (keeping in mind that userconfig will override primary config)

NNumber481 most things you can edit/save the config or the user config live (keeping in min...

blave549•10/30/23, 12:07 AM

I did not know that!

Number481•10/30/23, 12:09 AM

Yessir.... the only things you cant modify on the fly are the system variables (like enabled sims, etc).

Also, you can't add a new aircraft section while live either. That will require a restart (of telemFFB).

amadeus•10/30/23, 7:44 AM

i would say in general, avoid using friction, use damper instead

amadeus•10/30/23, 7:44 AM

i.e. jack damper back up to 100%, (probably worth doing the same with inertia as well), and maybe keep friction in the Settings tab at 10% or lower, and also yeet it from the effects tab and instead add some damper to give it that mechanical feeling

SnooperOP•10/30/23, 10:49 AM

the thing is that I had friction all 100 with no issues prior the last update from TelemFFB

SnooperOP•10/30/23, 10:51 AM

should I remove Friction in the effects tab too?

SnooperOP•10/30/23, 11:32 AM

what is this? often it happens and I have to restart TelemFFB.

SnooperOP•10/30/23, 11:32 AM

Traceback (most recent call last):
File "main.py", line 449, in process_data
File "aircrafts_msfs.py", line 712, in on_telemetry
File "aircrafts_msfs.py", line 680, in on_telemetry
File "aircrafts_msfs.py", line 571, in _update_flight_controls
File "simconnect\sc.py", line 197, in send_event
File "simconnect\datadef.py", line 137, in map_event_id
File "simconnect\sc.py", line 66, in _callable
File "_ctypes/callproc.c", line 993, in GetResult
OSError: [WinError -1073741648] Windows Error 0xc00000b0

During handling of the above exception, another exception occurred:

Traceback (most recent call last):
File "traceback_with_variables\print.py", line 67, in printing_exc
File "traceback_with_variables\print.py", line 98, in wrapper
File "main.py", line 488, in run
File "main.py", line 453, in process_data
File "traceback_with_variables\print.py", line 39, in print_exc
AttributeError: 'NoneType' object has no attribute 'write'

During handling of the above exception, another exception occurred:

Traceback (most recent call last):
File "threading.py", line 1009, in _bootstrap_inner
File "traceback_with_variables\print.py", line 92, in wrapper
File "contextlib.py", line 153, in exit
File "traceback_with_variables\print.py", line 70, in printing_exc
File "traceback_with_variables\print.py", line 39, in print_exc
AttributeError: 'NoneType' object has no attribute 'write'

SSnooper the thing is that I had friction all 100 with no issues prior the last update fr...

Number481•10/30/23, 12:01 PM

If you have friction enabled, and your hand is the only thing moving the stick, the oscillations might not occur. However, s soon as the trim/AP following in latest TelemFFB is moving the stick by itself without your hand on it to stop the oscillations from beginning to amplify.. that can absolutely start the oscillations.

Also... while your friction slider is %100.. you are limiting it to %20 in the effects tab.. important to understand how the two tabs work together.

SSnooper what is this? often it happens and I have to restart TelemFFB.

Number481•10/30/23, 12:08 PM

Can't say for sure. I've not seen that myself nor had any other reports of similar errors...

It looks like an issue with the simconnect code sending the axis position to MSFS.

How is the stability of your USB connection to the Rhino? Does it ever momentarily disconnect/reconnect by itself?

NNumber481 Can't say for sure. I've not seen that myself nor had any other reports of simi...

SnooperOP•10/30/23, 2:04 PM

no, just happens in the sim

NNumber481 Can't say for sure. I've not seen that myself nor had any other reports of simi...

walmis•10/30/23, 2:27 PM

0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should recover automatically and probably would be a good idea to put the send_eventsend_event into a try .. except .. block

Wwalmis 0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should reco...

Number481•10/30/23, 2:39 PM

easy enough!

SnooperOP•10/30/23, 2:58 PM

glad to help

SnooperOP•10/30/23, 4:37 PM

ok, I believe its the engine rumble effect that causing the disconnect of X axis

SSnooper ok, I believe its the engine rumble effect that causing the disconnect of X axis

walmis•10/30/23, 4:41 PM

Can you check the fault code when the axis disconnects? It's in the bottom right in the status bar of the VPConf application

SnooperOP•10/30/23, 4:42 PM

sdby i'll do it again, I'm in Vr and i doesnt help to this kinds of tests

SnooperOP•10/30/23, 4:44 PM

SnooperOP•10/30/23, 4:45 PM

here better than copy the text

SnooperOP•10/30/23, 4:45 PM

hope not too much serious.. to my end......

SnooperOP•10/30/23, 4:47 PM

thats why I could recover from it by pressing the red button and then restart it

walmis•10/30/23, 4:50 PM

The safety algorithm is a bit too sensitive, I'll send you a firmware update later

SnooperOP•10/30/23, 4:55 PM

thanks

SnooperOP•10/30/23, 4:55 PM

can I reduce the engine tumble too in telemFFB? Look too much

SnooperOP•10/30/23, 4:56 PM

meanwhile I turn it off

walmis•10/30/23, 5:10 PM

Yeah, there are parameters for reducing the engine rumble

SSnooper can I reduce the engine tumble too in telemFFB? Look too much

Number481•10/30/23, 5:20 PM

you can add these to the msfs propeller aircraft config, or to a specific aircraft section:

engine_rumble = yes                     # Enable rumble effect (default = 0 (disabled)) - 1=enabled, 0=disabled)
engine_rumble_lowrpm = 650              # low RPM threshold for low rpm intensity setting 
engine_rumble_lowrpm_intensity = 0.06   # peak intenstiy of engine rumble at low RPM threshold
engine_rumble_highrpm = 2800            # high RPM threshold for high rpm intensity setting
engine_rumble_highrpm_intensity = 0.03    # peak intensity of engine rumble at high RPM threshold

engine_rumble = yes                     # Enable rumble effect (default = 0 (disabled)) - 1=enabled, 0=disabled)
engine_rumble_lowrpm = 650              # low RPM threshold for low rpm intensity setting 
engine_rumble_lowrpm_intensity = 0.06   # peak intenstiy of engine rumble at low RPM threshold
engine_rumble_highrpm = 2800            # high RPM threshold for high rpm intensity setting
engine_rumble_highrpm_intensity = 0.03    # peak intensity of engine rumble at high RPM threshold

Number481•10/30/23, 5:21 PM

intensity decreases as RPMs increase (defined by the high/low RPM and intensity settngs)

Number481•10/30/23, 5:22 PM

I should (and will) add the defaults to the MSFS section

walmis•10/30/23, 5:24 PM

There's also jet engine and afterburner rumble parameters

Number481•10/30/23, 5:25 PM

was just assuming they were still flying the comanche based on previous discussions

SnooperOP•10/30/23, 5:48 PM

yes yes always the comanche!!! i'm true love this month!!! I personally like more the Dash 8 Q200 but i'm on vacation

amadeus•10/30/23, 7:07 PM

@walmis do you know if there's any way to get rid of those chrome/edge webusb notifications? is this just a by product of the type of APIs used by the firmware?

amadeus•10/30/23, 7:07 PM

i.e. whenever a rhino is plugged in, they pop up

Aamadeus @walmis do you know if there's any way to get rid of those chrome/edge webusb no...

Number481•10/30/23, 7:28 PM

uninstall all traces of Edge from your machine and then call a witch doctor to make sure it is pure... then install Brave

Number481•10/30/23, 7:29 PM

I can't get Edge to stop it either... then the notifications get 'stuck' and the only way to get them to go away is to kill all the edge processes

amadeus•10/30/23, 7:31 PM

chrome does it too lol, so i get double

amadeus•10/30/23, 7:31 PM

but none of my other controllers have this problem, i assuming it's something related to a webusb api?

NNumber481 I can't get Edge to stop it either... then the notifications get 'stuck' and the...

amadeus•10/30/23, 7:32 PM

yeah, if i forget to close it, it seems to get stuck heh, and with an ultrawide, it's something that can sometimes be missed lol

Number481•10/30/23, 7:33 PM

Only have Edge and Brave (my default).. Brave will popup if you plug/replug.. but it goes away by itself or you can close it.. edge is a PITA and I think their WebUSB is messed up

amadeus•10/30/23, 7:34 PM

uninstalling the browsers isn't something i can really do given my line of work/job

engine_rumble = yes # Enable rumble effect (default = 0 (disabled)) - 1=enabled, 0=disabled) engine_rumble_lowrpm = 650 # low RPM threshold for low rpm intensity setting engine_rumble_lowrpm_intensity = 0.06 # peak intenstiy of engine rumble at low RPM threshold engine_rumble_highrpm = 2800 # high RPM threshold for high rpm intensity setting engine_rumble_highrpm_intensity = 0.03 # peak intensity of engine rumble at high RPM threshold

Is it possible that A2A comanche has some FFB implementation that makes some problems with telemFFB?

Similar Threads