Should you or can you use both the VP configurator and windows game controller to calibrate the joys
Should you or can you use both the VP configurator and windows game controller to calibrate the joystick?
SI need to put in an order for a replacement vkb adapter. How do I do that?
AWith the rhino, never use the windows game controller calibrator
Swhy this windows stays all time open here? i can not click X
Nbecause microsoft edge is a cancer
Nyou can try disabling it in the edge settings.. but its %50/50 whether it honors that setting or not, in my experience...
Sthanks mate
3Thanks
MI just hooked up my Rhino to a winwing F18 stick using the winwing adapter. All buttons work except the trim hat. That is; the button works but right/left/up/down does not register. Any ideas? Thanks in advance
Mcheck those settings in the FFB configurator software?
MThanks! I now saw that I hadnt changed the grip type. Changed it to winwing adapter and all works flawless! Thanks @mr.s4232
IMine just shipped, is there a tutorial on how to setup the FFB Rhino?
F#
knowledge-base manual
knowledge-base manualIThanks
LDoes any know how to make winwing adapter works for rhino? I have selected the winwing adapter in grip type
L
LNone of the buttons worked, no reaction
MSorry for the obvious question, but did you apply/store the profile?
JThis, did not work.
NMicrosoft.com/support?
N1-800-EXORCIST
JHa! Might as well...
Syeap it did not nothing....
FIs there a wiring diagram available for the FFB kits? I finally opened the box I got a couple of months ago, and there's no docs in there at all. 
F
FPerfect @.flatspin, thank you!
F24v acceptable if I can't source a 20v supply?
FI think Walmis recommends the 24v 350W meanwell
F350.4W 24V 14.6A Single Output Switchable Power Supply 24 Volts @ 14.6 Amps
FGot it, thanks.
SDoes anyone know if the VKB-to-Rhino adapter will work for the new Mk 4 grips/button box? If not, is there a Mk 4 adapter or will there be one on the way?
FI don't believe so.
οΏ½Ultimately, I was not able to get my WinWing F-16 stick working with firmware version 1.0.16 (it worked with 1.0.15) despite the debug saying the adapter was fine. I switched to the Virpil Alpha grip.
RHey guys, good morning! The vkb ultimate grip mkv works on rhino?
R
FMK III afaik
II don't understand why they need to change the adapter every revision.
MThe first one sucked, the last one was good, but flawed. this most recent one, barring any unforseen issues should have much better longevity
BGot to pay for the eight+ year long development time for the throttle somehow I guess.
MSuch things are the price of not just going with the current and using 5 pin DIN (which sucks ass) like everyone else
SFYI Tomcat pilots
The latest patch has the FFB trim setting reversed. Unchecked enabled F-14 trim implementation, checks turns it off
The latest patch has the FFB trim setting reversed. Unchecked enabled F-14 trim implementation, checks turns it off
AI flew the F14 over the weekend and feel like I didnβt notice this? 
AYou will need a VKB blackbox to handle the grip, and a VKB adapter from Walmis.
Not sure if he has done any work on a RevC version of that adapter yet, but perhaps it could be modified using a VKB base connector upgrade kit.
Not sure if he has done any work on a RevC version of that adapter yet, but perhaps it could be modified using a VKB base connector upgrade kit.
SYea when I fired it up last night, first time after last patch.....trim would just run away and park itself full aft and then full forward and never respond.
No double mappings, update the stick firmware, sp and mp the same
Disabling FFB Trim in "special, f-14" settings caused it to work again.
No double mappings, update the stick firmware, sp and mp the same
Disabling FFB Trim in "special, f-14" settings caused it to work again.
PHey where do I find the log? I've had the data log running & need to see it
Bit's in the installation directory
PI'm running vpforce config software from the folder, so it should be in there? I can't find anything with .log
BI thought you were talking about TelemFFB
Poh sorry, I should of been clear
PAnyone looking for log file like I was it is in the config software folder & it's a .csv file.
RJust received my Rhino and winwing adapter. This looks wrong to meβ¦ like I need to rotate with the plug in the adapter or the rhino baseβ¦ I assume Iβm best rotating the winwing adapter plug yes?
