PI'm running vpforce config software from the folder, so it should be in there? I can't find anything with .log
BI thought you were talking about TelemFFB
Poh sorry, I should of been clear
PAnyone looking for log file like I was it is in the config software folder & it's a .csv file.
RJust received my Rhino and winwing adapter. This looks wrong to me… like I need to rotate with the plug in the adapter or the rhino base… I assume I’m best rotating the winwing adapter plug yes?
WYeah, it's rotateable inside the winwing adapter
RCan I just… twist, or do I need to take it apart?
WYeah, definitely no need to take it apart 
RCool… well… going to have to be destructive as I’ve stripped the head of one of the 4 screws on the opposite end 
RI can make it all fit without the 3D printed part/insert with the arrow shown in the picture… any concerns about just removing that?
ROr! Keeping that part just not screwing it into place on the adapter. So it’s still in the grip as a spacer, just not held in with those two screws…
WYou can plug the 6pin WW connector and twist it, it should turn without much resistance
WIt should align like this
RAh perfect, I misread your first response! I read it as “definitely no! (Don’t turn it) you need to take it apart”
RBoom, done, perfect!
IMine just arrive, cannot connect, I get this error
I
INotFoundError: Failed to execute 'requestDevice' on 'USB': No device selected.
Nthats the same error you would get if you didn't have a rhino plugged in at all. Are you sure windows is recognizing it?
IIts recognized, I plugged it and got a message to connect Rhino so it took me to the connect window
I
IIt works now
IIn DCS I am not getting any effects except for stall buffet, what do I need to do to get the effects?
NTelemFFB is the telemetry app that enables all of the additional effects. DCS native implementation is limited to the dynamic stick forces and stall buffeting as you are experiencing. Head over to #VPforce-TelemFFB and download the latest from the pinned link. You can read up on TelemFFB in the manual linked in #VPforce Rhino WIP Manual 
Iany way to have different VPForce configurations, let's say one for helicopters and another for jets?
Ialso what is it supposed to do the trim option in DCS, for helicopters, do we need to still enabling trim effect in VPForce effects? Thnaks
Nyou can use the vpconf config setting inside the TelemFFB config to load any vpf configurator setup for a whole sim, aircraft category or specific aircraft, depending on where you put the setting in the config: 📃general
TelemFFB does not do anything special for helicopter trim in DCS. That is all handled by the native FFB implementation and the force-trim settings in DCS (for all modules you will want either the "instant" or "default" in their special settings, depending on the module).
TelemFFB does not do anything special for helicopter trim in DCS. That is all handled by the native FFB implementation and the force-trim settings in DCS (for all modules you will want either the "instant" or "default" in their special settings, depending on the module).
Ithank you
II have this problem when I enable friction, if I disable it, it return to the strimmer center
PIf you read the subsequent messages above, it turned out that I didn't have a config or hw issue. I simply misunderstood the intended behavior.
IPitch forces feel softer than roll , what setting do I need to change to make them equal?
IBu the way Telem FFB introduced a virus that has been a pain in the ass to remove.
II clicked on the FFB screen on the link on the bottom left corner and that inmediatelly started the virus
NThere is no virus in TelemFFB. Hundreds of people in here are running it. The source is open on GitHub too if you want to look at it.
Windows defender and some other AV tools will sometimes flag it as a virus however. This is because it is written in Python and compiled with ‘pyinstaller’ which can sometimes result in certain file hashes that are often found in low tech malware that is commonly also written in Python and compiled with pyinstaller.
Windows defender and some other AV tools will sometimes flag it as a virus however. This is because it is written in Python and compiled with ‘pyinstaller’ which can sometimes result in certain file hashes that are often found in low tech malware that is commonly also written in Python and compiled with pyinstaller.
R@walmis after getting my adpater in place yesterday I've only now got around to testing it and I'm unable to get my WinWing F18 stick buttons working. Firmware is v1.0.16 - any suggestions?
RNot a single WinWing button is highlighting when clicked in...
1) Microsoft game controllers (which I realise I should ignore anyway)
2) The WebUSB tool
3) The RAW BTN column in the VPforce Configurator
I have grip type selected as "WinWing Adapter" but I've tried all the others as well (just to test) and nothing is working
1) Microsoft game controllers (which I realise I should ignore anyway)
2) The WebUSB tool
3) The RAW BTN column in the VPforce Configurator
I have grip type selected as "WinWing Adapter" but I've tried all the others as well (just to test) and nothing is working
RLegobirds - do you get yours working?
WSomething is not mating properly most likely, let's see which side is not talking:
1: set Generic grip debug
1: set Generic grip debug
- Open Debug Tab and check the data that it's printing
WIf the data is all FFs then the adapter is not talking to the base
R
Rlooks like that's the case then
Wmaybe it's not inserted properly, the star pattern should insert fully into the base
Ri'll double check
Rshould it "work" without the joystick head attached?
Wyeah
WI recommend holding it like this and plugging it into the socket
Rok, I've tried a couple of times and I'm pretty confident i've got it fully in place - but still reporting back all FFF
Wd'oh, before I send you a new one, can you remove bottom start piece from the adapter and check?
Ryeah, just did that as well - figured it might be blocking it going in all the way or something - no luck 
WNot sure what went wrong there, since I've tested it before shipping without issues